Installation Guide

ManualsBrandsGE ManualsIndoor FixturesGE BR Series

Back-lit recessed troffer 22 SeriesBack-lit recessed troffer 14 Series

Back-lit recessed troffer 24 Series

Lighting

Installation Guide

imagination at work

(Back-lit recessed troffer Series: Standard, 347V, and Lutron)

Lumination

LED Luminaires

BEFORE YOU BEGIN

Read these instructions completely and carefully.

Save These Instructions

Use only in the manner intended by the manufacturer.

If you have any questions, contact the manufacturer.

Components Supplied

• Luminaire

• Mounting Bracket

WARNING/AVERTISSEMENT

RISK OF ELECTRIC SHOCK

• Turn power off before inspection, installation or removal.

• Properly ground electrical enclosure.

RISK OF FIRE

• Follow all NEC and local codes.

• Use only UL approved wire for input/output connections.

Minimum size 18 AWG (0.75mm

RISQUES DE DÉCHARGES ÉLECTRIQUES

• Coupez l’alimentation avant d’’inspecter, installer ou déplacer le luminaire.

• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.

RISQUES D’INCENDIE

• Respectez tous les codes NEC et codes locaux.

• N’utilisez que des ls approuvés par UL pour les entrées/sorties de

connexion. Taille minimum 18 AWG (0.75mm

Prepare Electrical Wiring

Electrical Requirements

• The LED driver must be supplied with 120-277VAC or

347VAC, 50/60Hz and connected to an individual

properly grounded branch circuit, protected by a 20

ampere circuit breaker. Use min. 75°C supply conductor.

Grounding Instructions

• The grounding and bonding of the overall system shall

be done in accordance with National Electric Code (NEC)

Article 600 and local codes.

Tools and Components Required

• Torx or Philips screwdriver

• UL Listed conduit connections per NEC/CEC for

nominal conduit trade sizes ½” or ¾”

• UL Recognized wire connectors

Summary of content (4 pages)

PAGE 1
Installation Guide GE Lighting Lumination LED Luminaires TM (Back-lit recessed troffer Series: Standard, 347V, and Lutron) Back-lit recessed troffer 14 Series Back-lit recessed troffer 22 Series Back-lit recessed troffer 24 Series BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT RISK OF ELECTRIC SHOCK • Turn power off before inspection, installation or removal. • Properly ground electrical enclosure. RISK OF FIRE • Follow all NEC and local codes.
PAGE 2
Luminaire Installation 1 Carefully unpack unit from its packaging. Properly inspect for defects before installing. Wear work gloves to prevent dirt and oil from being transferred to the luminaire. Back-lit recessed troffer 14 Series 2 Install the unit into the reserved hole in the ceiling. Back-lit recessed troffer 22/24 Series Bend clips 3 For Back-lit recessed troffer 14, bend the 4 clips into the grid to secure the luminaire in place.
PAGE 3
Back-lit recessed troffer 14 Series Back-lit recessed troffer 22/24 Series AC line Install listed electrical fittings in the knockout holes for wire protection. Connect the AC line to the black (line), white (neutral) and green (ground) input wires of the LED driver using 18-14AWG twist-on wire connectors.
PAGE 4
Back-lit recessed troffer 14 Series Back-lit recessed troffer 22/24 Series Dimming line 3 Dimming line Install listed electrical fittings in the knockout holes for wire protection. Connect the dimming control (grey and purple or purple and purple/white) wires of the LED driver using 18-14AWG twist-on wire connectors. Back-lit recessed troffer 14 Series 4 Back-lit recessed troffer 22/24 Series Replace electrical enclosure cover. Secure it with the star washer and the screw.