Smart Wall Switch 3-Wire Installation Guide 3-Wire Smart Switches & Dimmers Models CSWONBLBWF1NN CSWONBLPWF1NN CSWONBLTWF1NN CSWDMOCBWF1NN CSWDMBLBWF1NN
Simple DIY Set Up WARNING: RISK OF ELECTRIC SHOCK This product installation requires handling 120 volt wiring. Follow each step carefully. If you have any concerns handling wiring, hire a qualified electrician. Ensure all work meets local and federal regulations.
Let’s Do It Compatibility Requirements Rating 120V AC 60Hz LED up to 1.25 amps (150 Watts) Neutral wire is not required (Wire is usually white or grey and is not required) Incandescent/halogen up to 5 amps (450 Watts) Ground wire is required (Wire is usually green, green with a yellow stripe, or copper) Wi-Fi 802.11 b/g/n @ 2.
BEFORE YOU DO ANYTHING! Turn Off the Power! You Got This! And we’re here to help. For in-depth instructional videos and a guided tour through the installation, go to gelighting.com/cync. NOTE: Please make sure your system is up-to-date, and you update the firmware when prompted for the best experience. STEP 1 Turn off the power for the switch location at the circuit breaker box. ON OFF STEP 2 Test existing switch by toggling switch on/off, ensuring lights do not turn on.
STOP! What type of bulbs do you plan to use? You may need to install a Bulb Adaptor. Some installations require the included Bulb Adaptor to maintain Wi-Fi connectivity and to ensure your switch and bulbs work together.
Remove Your Old Switch STEP 1 Remove the existing wall plate and switch from the wall. STEP 2 Use voltage tester on the black wires to confirm power to the switch is off (recommended). STEP 3 Before disconnecting the wires from the wall, label each with the provided wire labels. Ground wire is required. If you don’t have this wire, the Cync or C by GE Smart Switch is not compatible. STEP 4 Disconnect wires and remove existing switch.
Connect the Wires NOTE: Both black wires on the switch are interchangeable and can be connected to either the load or line wire from the wall. STEP 1 STEP 4 Connect the first line/load (black) wire on the switch to the line or load (black label) wire from the wall. Cap the 3-way/multi-way traveler wire (if applicable). For 3-way switch setup, visit gelighting.com/cync STEP 2 Connect the second line/load (black) wire on the switch to the line or load (black label) wire from the wall.
Fit Wires Into Wall Box Secure the Smart Switch STEP 1 STEP 1 Neatly push the wires back into the box, rotating the switch so it’s oriented according to the image, and the arrow on the switch is pointing up. Using a Phillips screwdriver and the screws provided, secure the switch to the wall until level and flush. Then snap the faceplate cover onto the bracket. If using your existing wall plate, you may need to replace the existing wall plate screws with the short screws provided.
Turn the Power Back On TROUBLESHOOTING LED indicator light or light ring will flash blue until the switch is added to the Cync App. LED indicator light or light ring will not illuminate if wired incorrectly or if the switch circuit does not meet the specified load requirements. TIP: To enable the full experience, you’ll need to set up all your products in the Cync App. If you’ve set up C by GE or Cync bulbs in the Google Home app, visit gelighting.com/cync for unpairing instructions.
Simple Set Up Using the CYNC App Unlock full features and connect to other CYNC devices STEP 1 Install your Smart Switch STEP 2 Download the Cync App, powered by Savant, on your smartphone STEP 3 Add your Smart Switch to the Cync App STEP 4 Easily connect your Smart Switch to your Amazon Alexa- or Hey Google-enabled device in the Cync App For set up help, visit gelighting.com/cync GE and C by GE are trademarks of General Electric Company. Used under trademark license.
Additional Information and Warnings This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s) Operation is subject to the following two conditions: 1. This device may not cause interference. FCC Compliance Statement Compliance Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
For supply connections, use copper wire only rated at 75ºC CAUTION - High Voltage - Disconnect power supply before servicing Operation temperature: 0-40ºC For Control of Electronic Ballast, CFLs, LED, and LED Lamps Type 1 Enclosure IP20 TM Pollution Degree 2 Impulse Voltage: 2500V Type 1 action Indoor use only. Like your new Smart Switch? Share your experience! Leave a review where you purchased the product.
PK-00102798-3
