INSTALLATION INSTRUCTIONS Straight Rail Kit Stair Rail Kit Deck Board Brackets Complete Post Kit & Post Sleeve Ultra Post Kit Synthetic Porch Posts
Straight Rail Kit Installation Instructions Tools Required Before You Begin: Figure 1 Important Information • No finishing is required. Painting QuickRail Plus® products is NOT recommended and will void the warranty. • A full line of additional QuickRail Plus accessories are available to complement the Straight Rail Kit (Sold separately at Menards and Menards.com ). ® Hacksaw ® or Circular Saw ® • Read installation instructions carefully before beginning your QuickRail Plus system installation.
Straight Rail Kit Installation Instructions [Continued] QuickRail Plus Accessories Figure 6 Step 6: Locate the crush block and cut to the proper length. The formula for determining the correct crush block length is: Desired clearance from bottom rail to mounting surface + 31/4" = length of crush block. Note: Spindle lengths are sized for a traditional 2" clearance from bottom rail to mounting surface.
Stair Rail Kit Installation Instructions Before You Begin: Figure 1 Tools Required Important Information • The mounting brackets and covers included in this kit are designed for stair applications with a 30 - 40° slope. • No finishing is required. Painting QuickRail Plus products is NOT recommended and will void the warranty. ® Hacksaw • A full line of additional QuickRail Plus accessories is available to complement the Stair Rail Kit (Sold separately at Menards and Menards.com ).
Stair Rail Kit Installation Instructions [Continued] of the bottom rail. Figure 6 1 Step 7: Slide the bottom rail upper and lower bracket covers onto the respective 2" ends of the bottom rail. Position the rail so it can be attached to the mounting brackets, making sure the rail sits on the resting flanges. Install two of the supplied 1" Phillips stainless steel pan head screws into each mounting bracket (1 on each side) in the middle slot of the brackets.
Deck Board Brackets Installation Instructions Tools Required Figure 1 Before You Begin: Important Information • Locate and review all materials in the box for easy access as you begin the installation process Hacksaw or Circular Saw • Locate all materials found in the box or package • Read installation instructions carefully before beginning your QuickRail Plus Deck Board Bracket Installation Screwdriver Installation Step 1: At each end of the top rail, place a deck board bracket up against the pre
Deck Board Brackets Installation Instructions [Continued] Figure 3 Step 6: Measure the deck board and cut to length so it is flush against the posts. Step 7: Chisel the center area at each end of the deck board. The area chiseled will need to be deep enough so that the deck board will sit flush over the top rail bracket covers on each end without a gap between the bracket and deck board. Step 8: Center the Deck board over the top rail.
Complete Post Kit & Post Sleeve Installation Instructions Before You Begin: Figure 1 Tools Required Important Information • Complete Post Kit can only be used for applications that are no more than 30" above ground. Refer to local building codes for requirements. Installation Drill with 5/16" Hex Bit Driver and #2 Phillips Bit Determine the mounting location for the post.
Ultra Post Kit Installation Instructions Figure 1 Before You Begin: Important Information Tools Required • Quickrail must be directly fastened to supporting construction to provide, and having, adequate strength and stiffness to meet the loads required by code. Installer must consult code official for compliance to building code requirements. Wood Post Mount Installation Lay out the location of the post. Install at least 3" of blocking under the mounting location.
Synthetic Porch Posts Installation Instructions Before You Begin: Figure 1 Important Information Tools Required • When installing QuickRail™ railing to the post, pre-drill holes for bracket screws using a 1/8" drill bit. • Before post is installed, slide one trim piece at the top of the post and one trim piece at the bottom of the post. Tape Measure Load Bearing Capacity 4" 5" 6" QuickPost® Square 3,000 lbs. 5,000 lbs. --- QuickPost® Colonial --- 3,000 lbs. 5,000 lbs.
Synthetic Porch Posts Installation Instructions [Continued] Colonial Trim Kit Sold Separately Installing Trim Kit (Trim Kit Sold Separately) Before post is installed, slide one trim piece at the top of the post and one trim piece at the bottom of the post. PVC glue can be applied to hold the Trim Kit into place at the top and bottom of the post. There may be some marginal spacing in the Trim Kit to Post fit. Exterior caulk can be used as a filler.
TM 1750 Indian Wood Circle | Maumee, OH 43537 | Phone: 800.446.3040 U.S. and Canada Fax: 800.446.9373 U.S. and Canada | www.fypon.com | info@fypon.com For complete warranty details and exclusions, visit the Product Support section at www.fypon.com. ©2015 Fypon LLC. All rights reserved. FYPON, the Fypon Logo and the QuickRail Logo are trademarks of Fypon LLC. Fypon LLC. and its parent company Therma-Tru Corp. are part of Fortune Brands Home & Security, Inc. Publication No.
