User's Manual Part 3

119
<Model Menu (Common Functions)>
 TouchtheRTNbuttontoendadjustmentand
returntothecursolmovemode.
●Offset mode setting
Offset mode is function which allows
simultaneous offset control of up 4 slave functions
per circuit.
1.Use[MODE]settingtoselecttheprogram
mixingoparationmode.[MIXING]isthe
normalmixingmodeand[OFFSET]isthe
offsetmode.
2.Movethecursorto[INHIBIT]ofthemixingNo.
settotheoffsetmodeandtouchtheRTN
button.Thesetupscreenisdisplayed.
3.PresstheS1button.Page5/5isdisplayed.
4.Movethecursortothe[STATUS]itemand
switchtothedateinputmodebytouching
theRTNbutton.
5.Turnthedialtotheleftandrightuntil[ACT]
blinks,andthentouchtheRTNbutton.To
deactivatethefunction,switchto[INH].
●ON/OFF switch selection
 Movethecursortothepage5/5[SWITCH]
item,calltheswitchsetupscreenby
touchingtheRTNbutton,andthenselect
theswitchandONdirection.(Foradetailed
descriptionoftheselectionmethod,see
[SwitchSelectionMethod]atthebackofthe
instructionmanual.)
●Slave No. selection
 SettingoftheslaveNo.from1to4atpages
1/5~4/5isdisplayed.WhentheS1buttonis
pushed,thedisplayedslaveNo.isswitched.
●Slave function setting
 Movethecursortothe[FUNCTION]itemand
switchtothedateinputmodebytouching
theRTNbutton.Selectthefunctionby
scrollingthedialandthentouchtheRTN
button.
●Offset rate setting
The function operation offset amount when
the mixing switch is ON and OFF can be set
independently.
1.Movethecursortothe[ON]or[OFF]item
andswitchtothedateinputmodeby
touchingtheRTNbutton.
2.Turnthedialtotheleftandrightandsetthe
offsetratewhentheswitchisONorOFF.
Initialsetting:0%
Settingrange:-300%~+300%
●Trim mode ON/OFF setting
1.Whenchangingthetrimmode,movethe
cursortothe[TRIM]itemandtouchtheRTN
buttontoswitchtothedatainputmode.
 SelectON/OFFbyscrollingthetouchsensor
andsettheselectionbytouchingtheRTN
button.
*When mixing includes master side trim, select [ON] and
when mixing does not include master trim, select [OFF].
*Effective when a function is set at the master channel.
●Slave channel AFR mode setting (STK-STK)
1.Movethecursortothe[STK-STK]item,select
themodebyscrollingthetouchsensor,
andchangethemodebytouchingtheRTN
button.
*When link is set at the slave side, and you want to add AFR
(D/R) to the mixing rate, select [ON].
*This is effective when the linkage is the same, but the travels
are substantially different.
●Mixing curve setting
(For a description of the curve setting method, see the
description at the back of this manual.)
●Fine tuning trim setting
Operation control [CTRL], operation mode
[MODE], and rate [RATE] adjustment is possible
by [FINE TUNING] item.
(For a description of the ne tuning trim setting method, see
the description at the back of this manual.)
●Servo speed setting
Adjustment is possible with the [SPEED] item.
(For a description of the servo speed setting method, see the
description at the back of this manual).
●Mixing ON/OFF delay setting
Delay time at mix ON [START] and delay time
at mix OFF [STOP] adjustment is possible by
[DELAY] item.
*This function is inactive when a mixing switch is not set.
1.Movethe[START]or[STOP]itemandtouch
theRTNbuttontoswitchtothedatainput
mode.
2.Adjustthedelaytimebyscrollingthetouch
sensor.
 Initialvalue:0.0sec
 Adjustmentrange:0~4sec
(When the RTN button is touched for 1 second, the delay time
is reset to the initial value.)