OW1-WIS Ave UNIT WEIGHT: 40 LB WEIGHT CAPACITY PER SHELF/TIER: 25 LB Tucson Etagere/Bookcase
1.00 16.25 12.00 16.25 13.50 13.50 13.50 69.00 64.00 13.50 13.50 5.00 OW1 12.
DISCLAIMER: Furniture Pipeline LLC intends to make this instruction manual accurate and complete. However, Furniture Pipeline LLC makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind.
[x3] Middle Shelves [x2] Top/Bottom Shelf 2 1 [x4] Upright Support [x1] Upright Support 3 4 [x1] Front Left Support 5 [x1] Front Right Support 6 NOTE: SMALL ADJUSTMENTS MAY BE NEEDED ON SUBASSEMBLIES DUE TO SHIPPING MOVEMENT OW1 4
[x1] Canvas Retaining Strap [x2] Top Connector 7 8 [x1] 1/4" Allen Key Large Key [x17] Ø8 x 40 mm Screws 10 9 [x1] 1/8" Allen Key Small Key 11 NOTE: SMALL ADJUSTMENTS MAY BE NEEDED ON SUBASSEMBLIES DUE TO SHIPPING MOVEMENT OW1 5
1 SMALL HOLES NO HOLES 1 2 2 2 LARGE HOLES 1 4 SMALL HOLES NO HOLES LARGE HOLES Use Part 11 to Tighten Shelves [x10] For Ease of Assembly, assemble laying down as shown. Protect floor from from being scratched by pipe.
2 5 6 FROM STEP 1 USE PART 11 THIGHTEN EACH FITTING ONTO PIPE For Ease of Assembly, assemble laying down as shown. Protect floor from from being scratched by pipe.
3 3 9 9 3 FROM STEP 2 9 Note: If you run into diffculties fitting the side panels between the sheves, use method illustrated below. ANGEL PANEL BETWEEN SHELVES THEN STRAIGHTEN TURN PAGE TO CONTINUE STEP 3 For Ease of Assembly, assemble laying down as shown. Protect floor from from being scratched by pipe.
3 Cont.. 4 Once all fittings are tightened, use partner to stand unit up as shown & proceed to put Tops (7) on.
4 IMPORTANT: TO INSURE PROPER AND SAFE INSTALLATION OF YOUR SHELF; YOU MUST: 1. PLACE THE UNIT IN DESIRED LOCATION AGAINST WALL . 2. LIGHTLY MARK YOUR WALL USING A PENCIL WHERE UPPER MOST STRUT INTERSECTS WALL STUD. 3. REMOVE UNIT FROM WALL AND PREDRILL YOUR 8 MARKED SPOTS USING A 3 " 16 DRILL BIT. 4. REPLACE UNIT TO DESIRED LOCATION AGAINST WALL AND WRAP PART 8 AROUND UPPER MOST LADDER STRUT. FASTEN THE WRAPPED STRAP INTO WALL USING THE 1/4" ALLEN WRENCH (PART 10) AND SCREWS (PART 9) PROVIDED.
WARRANTY Finishes of Pipes and Fittings, and all Other Parts and Components, Excluding Wood -1 Year Limited WarrantyAll metal finishes and other parts and components, excluding wood, are warranted by Furniture Pipeline LLC to you, the original retail purchaser, for a one-year period starting from the date of purchase, to be free from material manufacturing defects.
WARRANTY CONT... FINISHES AND ALL OTHER PARTS AND COMPONENTS EXCLUDING WOOD – 1 YEAR SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, THEREFORE, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. DISCLAIMER NO OTHER EXPRESS WARRANTY HAS BEEN MADE OR WILL BE MADE ON BEHALF FURNITURE PIPELINE LLC, WITH RESPECT TO THE FURNITURE AND ITS PARTS, OR THE OPERATION, REPAIR, OR REPLACEMENT OF THE FURNITURE AND ITS PARTS.
WARRANTY CONT... Claims If a problem should arise which you feel is covered by our Limited Warranty, contact the Furniture Pipeline LLC authorized retailer from whom you purchased your furniture. The original bill of sale and the product serial number are necessary for the fulfillment of the warranty. Please make sure any claim for warranty service is accompanied by the necessary information to satisfy the warranty requirements.
