ASSEMBLY INSTRUCTIONS . VERSION # 20-09-24 1716 TOOLS REQUIRED Allen Wrench {included) e Phillips Screwdriver {Not Included) People g Recommended issuance v 000:0 EASY e DIFFICULT The Assembly Rating is a S-point system showing the revel of effort needed to assemble a specific product.
CHECK BEFORE STARTING Are you missing anything? Double-check all parts, hardware and accessories listed on Page 6 are accounted for, Should we send any replacements? Are there any irregularities or flaws in the parts? We can send replacements! Check out our Quick Tips! We recommend reviewing the per-assembly handouts. Even experts need a refresher now and then Prep Time! Please review the assembly instructions and aff diagrams prior to assembling.
PRE ASSEMBLY INTRODUCTION We understand building ready-to-assemble furniture can be a challenging experience fur some. To help avoid confusion, we have provided some helpful tips that may speed up the process. O Teamwork ALWAYS have at least two people to help with transporting and assembling the product to avoid potential injury and/or damage. Suitable Location Assembling near the area of the intended location is highly recommended.
ASSEMBLY AND CARE ADVICE FAILURE TO FOLLOW THE GUIDELINES BELOW MAY RESULT IN INJURY AND/OR PROPERTY DAMAGE. Turn clockwise to tighten and only tighten when step is competed or when instructed o do so. Position each part correctly and Insert screws or boils into their rasp active holes. Use the appropriate hand looks or power tools for assembly. Select steps, such as lightening sowers and/or bolts, may require hand fools to avoid causing damage during assembly.
e = @1pc PCs @mc e P Bottom Panel Shelf Cross Bar Connected Bar 'lpc 1pc @ PCs Support Bar Top Cross Bar Shelf Board 1pc @ 4dpcs @‘ PCs o v F Tray Plastic Pad Bracket e @ PCs pests @ PCs AES) @ () Screw $4x22mm Bolt Bolt 1pc @ PCs Allen Wrench Leveler $1/4" Bolt 1pc @ Zoos 1pc — Screw $4x50mm Bracket Restraint Strap 6/16
ASSEMBLY INSTRUCTIONS ( Align the bosom panel top cross bar (#11} to front panel then secure by using bolts (#B) with washers s S Part Hardware *apes Hardware expel #11 assembly is complete. This will help all parts to assemble ( Align the right panel (#1} to bosom Part @ expo panel (#7) and lop cross bar then secure by using bolts (#B) with washers Hardware@8) apexes ..
ASSEMBLY INSTRUCTIONS panel (#7) and top cross bar then Part @(Wpc by using bolts with washers Hardware re PCs o J Hardware expel 4 Part @ expel Hardware PCs Hardware expert [ Align the top panel (#2) o top cross bar {#11) and right panel then secure | by using bolts (#B) with washers 8718
ASSEMBLY INSTRUCTIONS S Part ) IPO Hardware@B) PCs Hardware@ expel { Align the left panel {#3) to bottom panel 3 {#7) and top panel! then secure by using bolts (#8) with washers #2#T- 6 Part Hardware PCs Hardware expel | Align the connected bar (#9) to top panel {#2) and left pans then secure by using bolts (#B) with washers 9/16
ASSEMBLY INSTRUCTIONS 7 Align the support bar (#10) to left panel \ | then secure by using bolts #8B, i Part Alpo | #C) with washers Hardware x1pc Hardware Exposes Hardware@D) x1pc ~ ‘ Align the shied cross bars (#8) to panels | Part @secs | (#1, #4, #5), then secure by using bolts | | (#B) with washers Hardware apexes L (#B) with wi D) Hardware@ x1pc 10718
ASSEMBLY INSTRUCTIONS 1 1 #2.
ASSEMBLY INSTRUCTIONS 13 Part ¢ raps ; N P Align the plastic pad (#14) to bottom panel Part 1) ripe Place the tray ‘ P #13\§ 3 137186
ASSEMBLY INSTRUCTIONS 15 Hardware ch Hardware@ x1pc P Align the bracket {#H) to back panel | then secure by using bolts {_through the smaller hole. ) P 16 Hardware@ xpe Hardware@ xpe y {Locate the bracket (#H) on the wail over a wall stud and 2 inches below the bracket {#H) secured to the back of coat stand. Attach the wall stud using the screw {#G) provided, through the \smaller hale.
ASSEMBLY INSTRUCTIONS Y 17 Hardware ch { Place the furniture into position so both brackets {#H) are vertically in fine. Lace the end of the restraint strap through the larger hole in each bracket Bring both ends together and slide the flat end through the locking end and draw it through until alf slack is removed. i Confirm that the strap is securely laced and locked, ASSEMBLY COMPLETED Plea ensure the furniture rats on an even and fiat surface.
ASSEMBLY INSTRUCTIONS == EXPANSION WALL ANCHOR Our provided expansion wall anchors are only suitable for masonry walls, such as drywall, plaster or concrete, and are best for folding lightweight items or tor anti-lip prevention, if you are unsure of the correct wall anchor to use with the product, please request professional guidance. liability for product damage or failure due to using the incorrect anchors will fall on the installer.