Display Operating Manual B24T-7 LED
Congratulations on your purchase of an innovative product from Fujitsu. Latest information about our products, tips, updates etc. can be found on the Internet at: "http://www.fujitsu.com/fts/" You can find driver updates at: "http://support.ts.fujitsu.com/download" Should you have any technical questions, please contact: • our Hotline/Service Desk (see the Service Desk list or visit: "http://support.ts.fujitsu.
Published by / Contact address in the EU Fujitsu Technology Solutions GmbH Mies-van-der-Rohe-Straße 8 80807 Munich, Germany "http://www.fujitsu.com/fts/" Copyright © Fujitsu Technology Solutions GmbH 2013. All rights reserved. Publication Date 10/2013 Order No.
B24T-7 LED Operating Manual Your LCD screen...
Remarks Notes on the product description meet the design requirements of Fujitsu and are provided for the purposes of comparison. The actual results may differ due to several factors. Subject to technical changes without prior notification. Fujitsu accepts no responsibility for technical or editorial mistakes or omissions. Trademarks Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited or its subsidiaries in the United States and other countries.
Contents Contents Your LCD screen... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Further information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 4 Fujitsu
Your LCD screen... Your LCD screen... has a whole range of useful features and functions, e.g.: • • • TFT display (Thin Film Transistor; active matrix) minimal space requirements thanks to slim casing optimum ergonomic characteristics (totally distortion-free, excellent picture definition and colour purity right into the corners) • high degree of brightness and good contrast • high resolution (1920 x 1080) • presentation of up to 16.
Your LCD screen... Further information Details of how you set the resolution and refresh rate are provided in the documentation for your display adapter and the associated driver software. For ergonomic reasons, we recommend a screen resolution of 1920 x 1080 pixels. Because of the technology used (active matrix) an LCD monitor provides a totally flicker-free picture even with a refresh rate of 60 Hz. Notational conventions Pay particular attention to text marked with this symbol.
Important notes Important notes Notes Importantnotes In this chapter you will find information regarding safety which it is essential to take note of when working with your device. Safety instructions This device complies with the relevant safety regulations for data processing equipment, including electronic office machines for use in an office environment. If you have any questions about whether the device can be used in the intended environment, please contact your sales office or our Service Desk.
Important notes • • • • • • • The device may only be operated in wide format (0° landscape mode) and high format (90° portrait mode). The buttons of the control panel are located at the bottom in the middle of the monitor in wide format (0° landscape mode) and at the left-hand side of the monitor in high format (90° portrait mode). Store this manual close to the device. If you pass the device on to third parties, you should pass this manual on with it.
Important notes Cleaning the device Switch off the device and unplug the power plug. Do not clean any interior parts yourself, leave this job to a service technician. Do not use any cleaning agents that contain abrasives or may corrode plastic. Ensure that no liquid enters the device. The display surface of the device is sensitive to pressure and scratches. Clean it only using a soft, slightly moistened cloth. The surface of the casing can be cleaned with a dry cloth.
Important notes Disposal and recycling This device has been manufactured as far as possible from materials which can be recycled or disposed of in such a way that the environment is not damaged. The device may be taken back after use to be reused or recycled, provided that it is returned in a condition that befits its intended use. Any components not reclaimed will be disposed of in an environmentally acceptable manner.
Getting started Getting started Unpacking and checking the delivery The display surface of the device is sensitive to pressure and scratches. Always hold the device by the casing! The complete device package includes: • • • • • • • • • • one monitor one data cable (DVI) one data cable (VGA) one USB cable one audio cable one power cable one CD with software and documentation one Warranty Booklet a flyer "Quick Start Guide" one "Safety/Regulations" manual ► ► ► ► Unpack all the individual parts.
Getting started Setting up the device To ensure sufficient ventilation, the air inlet and outlet openings of the device must be kept clear. Setting up an ergonomic video workstation ► Do not position the video workstation opposite a window (1). 1 1 12 ► Position the monitor outside the reach of a light source (1).
Getting started ► Position the keyboard where it is easiest to reach (1). 1 ► Position the monitor so that the eye distance to the screen (1) is around 50 cm. 1 50 cm ► Position the monitor for optimum viewing (1). The monitor should under no circumstances fall outside the permissible viewing space (2). Depending on the situation, it may be advisable to use a swivel arm or similar accessory (VESA FPMPMI), which are available from specialist dealers.
Getting started Mounting the monitor base Do not remove the retaining splint before you have secured the base plate on the monitor and have brought it into operating position. ► ► ► ► Insert the base plate on the foot (1). Guide the screw through the opening (2). Secure the base plate with the screw (3). Place the monitor in operating position.
Getting started Adjusting height The height adjustment is fixed in the transport position. ► To free the fixing, remove the locking pin on the flange (1). The height of the monitor can be adjusted by approximately 130 mm. ► Grasp the monitor with both hands on the right and left edge of the casing and move it up or down (2). 2 1 Adjusting the inclination The inclination of the monitor can be adjusted by -3° (forwards) and +35° (backwards) from its vertical position.
Getting started Removing monitor base Before you can use a swivel arm or a similar accessory, you must remove the monitor base. The display surface is susceptible to scratching! 1 2 ► Switch off the monitor and pull the power plug out of the power socket. ► Lay the monitor on its face on a soft surface. ► Disconnect all cables. ► Release the base stand by moving the slider in the direction of the arrow (1) and hold it while lifting the complete base stand up (2).
Getting started Connecting the device Please observe the safety information in "Important notes", Page 7. CE conformance and optimum picture quality are guaranteed only if you use the data cables supplied. ► Switch off the monitor and the computer. ► Disconnect the power plug from the computer. Connecting cables to the monitor The data cables supplied have two 15-pin D-SUB connectors or two 24-pin DVI connectors for connection to the monitor and to the computer.
Getting started ► Connect one of the connectors of the data cable to the D-SUB socket or the DVI-D socket or the DP socket of the monitor and secure the plug connection by tightening the retaining screws. The monitor automatically detects the input when only one signal source is connected. ► Insert one plug of the audio line in the AUDIO IN socket on the monitor and make sure it is properly engaged. ► Plug the power cable supplied into the power connector of the monitor.
Operation Operation Switching the device on and off 1 1 2 2 1 = ON/OFF switch 2 = Power supply indicator The colour of the power indicator changes as follows: Power indicator blue green orange does not light up Status Monitor Monitor Monitor Monitor and computer are switched on (normal mode). and computer are switched on (ECO mode). is not receiving a video signal or is in power saving mode. is switched off. ► Switch the device on again with the ON/OFF switch (1).
Operation Notes on power management If your computer is equipped with power management (power-saving mode), the monitor can fully support this function. Here the monitor does not distinguish between the individual energy-saving modes of the computer (standby mode, suspend mode and OFF mode), as it is capable of immediately switching into the mode with the highest energy-saving effect.
Operation Changing the monitor settings When putting the monitor into operation for the first time, the screen display should be optimally adapted to the display adapter used. The buttons of the control panel have two functions. When the OSD menu (On-Screen Display) is active, the current meaning of the buttons is shown directly over the buttons on the edge of the screen. The display over the buttons varies depending on the sub-menu chosen.
Operation Changing the monitor settings with the buttons of the control panel With the OSD menu not activated, you can make the following settings directly.
Operation Select input signal (D-SUB/DVI-D/DP) ► Press the INPUT button to call the Input select setup window. / button or the / ► Press the monitor connection (VGA, DVI or DP). ► Press the MENU / button to select the desired button to confirm or the AUTO / button to cancel. This setting window can also be called when the OSD menu is locked. Performing auto-adjustment of the monitor This setting is only possible with an analog VGA input. ► Press the AUTO button for about 1 second.
Operation Changing the monitor settings using the OSD menu With the buttons on the control panel, you can call up and use the integrated OSD (On-Screen Display) menu. The English menu names are used in the following description (default setting). Enable OSD menu ► Press the MENU button to activate the OSD menu. The main menu appears with icons for the sub-menus. The first symbol, (Brightness/Contrast), is highlighted and the associated functions are visible in the right-hand menu field.
Operation Changing settings ► Press the ECO / ► Press the / button or the INPUT / button or the / button to highlight a function. button to change the setting. button to save the change or the ► Press the MENU / button to quit the function without change. AUTO / If you want to change other settings, select the corresponding function from the OSD main menu. All possible adjustments of the main menu are described in the following.
Operation Adjusting the brightness and contrast Call up the Brightness/Contrast setting window Brightness Set the brightness of the display Contrast With this function you change the brightness of the background lighting. Set the contrast of the display Black level With this function you modify the contrast of bright colour tones. Set the brightness of the display Auto level With this function you modify the contrast of dark colour tones.
Operation Adjusting the volume Call the Audio setting window Volume Mute Set the volume for playback with the integrated loudspeakers Switch the loudspeakers off or on Setting colour temperature and colours Call the Colour setting window Select the colour temperature The "warmth" of the screen colours is set using the colour temperature. The colour temperature is measured in Kelvin (K). You can choose between sRGB, 6500 K, 7500 K, 9300 K, Native and Custom Colour (user-defined setting).
Operation Setting functions in the Advanced menu Call up the Advanced setting window Input select Selecting the input signal This function allows you to switch the monitor from analogue to digital mode and vice versa, when several signal sources are connected. This requires that the graphic card used supports this function.
Notes on ergonomic colour adjustment Notes on ergonomic colour adjustment If you select colours for the monitor in your application programmes, take note of the information below. The primary colours blue and red on a dark background do not produce the minimum required contrast of 3:1 and are therefore not suitable for continuous text and data entry.
Troubleshooting Troubleshooting Should an error occur, first check the following points. If the distortion is still not eliminated, the monitor should, if possible, be checked on another computer. If you cannot solve the problem, please contact our Service Desk.
Troubleshooting Having this problem? Picture disturbances (vertical lines) Picture disturbances (horizontal lines, picture noise) The screen becomes darker Check the following points: ► Press the AUTO button to conduct the auto-adjustment of the screen. ► Press the AUTO button to conduct the auto-adjustment of the screen. The background lighting has a limited lifetime. If your monitor display should become too dark, the background lighting will have to be replaced. ► Contact our Service Desk.
Explanatory information about standard ISO 9241-307 Explanatory information about standard ISO 9241-307 Permanently unlit or lit pixels Today’s production techniques cannot guarantee an absolutely fault-free screen display. Depending on the total number of pixels (resolution), there may be a few constantly lit or unlit pixels or subpixels. Pixel Subpixel A pixel consists of 3 subpixels, normally red, green and blue.
Technical specification Technical specification Condensation is not permitted, neither in the rated range of operation nor in the limit range of operation. B24T-7 LED Dimensions and weight Visible diagonals Dot pitch Image size Maximum resolution Dimensions incl. monitor base Weight (without packaging) Storable display modes Pixel error classes according to ISO 9241-307 Electrical data Video 60.97 cm 0.2767 mm 531.4 mm 299.0 mm 1920 x 1080 571.72 mm 362.63 mm 203.98 mm approx. 6.
Technical specification VESA-DDC-compatible VGA interface Your monitor is equipped with a VESA-DDC-compatible VGA interface. VESA-DDC (Video Electronics Standard Association, Display Data Channel) is used as the communications interface between the monitor and the computer. If the computer is equipped with a VESA-DDC-compatible VGA interface, it can automatically read the data for ensuring optimum operation from the monitor and select the appropriate settings.
Technical specification SUB D port 5 1 10 6 15 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Fujitsu 11 Meaning Video input red Video input green Video input blue Ground Ground Video ground red Video ground green Video ground blue +5 V (DDC) Sync. ground Ground DDC Data H. sync V.
Technical specification DVI-D port 1 9 17 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 36 Meaning TMDS Data2– TMDS Data2+ TMDS Data 2/4 Shield not connected not connected DDC Clock DDC Data Analog Vertical Sync TMDS Data1– TMDS Data1+ TMDS Data 1/3 Shield not connected not connected +5V Power Earth Hot Plug Detect TMDS Data0– TMDS Data0+ TMDS Data 0/5 Shield not connected not connected TMDS Clock Shield TMDS Clock+ TMDS Clock– Fujitsu
Technical specification DisplayPort socket 19 17 15 13 11 9 7 20 19 16 14 12 10 8 6 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Fujitsu 5 3 4 1 2 Meaning Lane 3 (negative) Earth Lane 3 (positive) Lane 2 (negative) Earth Lane 2 (positive) Lane 1 (negative) Earth Lane 1 (positive) Lane 0 (negative) Earth Lane 0 (positive) Connected to earth Connected to earth Auxiliary channel (positive) Earth Auxiliary channel (negative) Hot Plug Detect Return for Power Power for connector (3.
