Cupboard Version:11/04/2022 1/27
IMPORTANT INFORMATION! please read the entire manual before starting to assemble and/or using this product.follow the manual thoroughly and keep it for further reference. AVOID SCRATCHES! In order to avoid scratching this furnuture should be assembled on a soft layer-could be a rug. IMPROVE EFFICIENCY ! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time. ANTI-TOPPLE WARNING ! Overturned furniture can cause serious or fatal crush injuries.
Please prepare the following tools When installing, please carefully confirm whether each screw corresponds to the manual, accessories with similar shapes can be distinguished by size A x 36 M5 x 40 mm B x 52 15 x 12 mm Cx6 D x 90 M7 x 50 mm M3.5 x 14 mm F x 16 Gx2 Hx2 Ix4 M5 x 40 mm M4 M4 x 20 mm DW Kx2 Lx2 Mx2 N x 20 M8 x 15 x 10 mm 45 mm Px4 M6 x 12 mm x1 #4 Q x 24 M3.5 x 14 mm R x 16 M6 15 x 4 14" 3508 3/27 S x 16 M6 x 60 mm E x 18 8 x 40 mm J x 20 1.
6 1 18 5 19 8 3 8 4 2 21 20 20 7 22 22 7 21 10 14 14 14 10 10 10 17 20 20 14 17 16 16 17 17 4/27 12 11 13 9 9 9 9
/27
1 D x 16 M3.5 x 14 mm Separate gilde into two parts at first. Fix No.15 slide rail to No.5 and No.6 plate using screw(D) as shown.
2 A x 10 M5 x 40 mm Insert quickfit screw(A) into corresponding holes in No.5 and No.6 plate with a screwdriver as shown.
Bx5 3 Ex5 15 x 12 mm 8 x 40 mm Connect No.14 and No.18 plate with No.5 using wooden dowel(E), and then turn cam lock(B) in No.14,18 plates clockwise to tighten as shown.
4 Bx5 Ex5 15 x 12 mm 8 x 40 mm Attach No.6 to No.14 and No.18 plate using wooden dowel(E), and then turn cam lock(B) in No.14,18 plates clockwise to tighten as shown.
5 Ax4 M5 x 40 mm Insert quickfit screw(A) into corresponding holes in No.5 and No.4 plate with a screwdriver as shown.
6 Bx4 Ex2 15 x 12 mm Px4 8 x 40 mm M6 x 12 mm Connect No.4 and No.5 plate with No.3 using wooden dowel(E), and then turn cam lock(B) in No.3 plates clockwise to tighten as shown. Connect No.4 and No.5 plate with No.19 steel tube using screw(P) as shown.
Cx6 7 M7 x 50 mm Attach No.2 plate to the bottom of the component and fix with screw(C) as shown.
Ax6 8 M5 x 40 mm Insert quickfit screw(A) into corresponding holes in No.1 plate with a screwdriver as shown.
9 Bx6 Ex6 15 x 12 mm 8 x 40 mm Ox2 M6 x 30 mm Cover No.1 plate to the top of the component using wooden dowel(E), and then turn cam lock(B) in No.4,5,6 plates clockwise to tighten as shown. Fix No.19 steel tube with No.1 plate using screw(O) as shown.
10 D x 32 M3.5 x 14 mm Kx2 M8 x 45 mm Fix No.16 leg support and No.17 leg to No.2 plate using screw(D) as shown. Rotate foot peg(K) into No.16 leg support as shown.
11 Q x 24 M3.5 x 14 mm Fix No.8 back plate using screw(Q) as shown.
J x 20 12 1.5 x 15 mm Nx6 15 x 10 mm Reinforce back plate using nail(J) again. Two back plate are fixed together using iron sheet(N) and nail(J) as shown. Iron sheet(N) can be used according to your needs.
13 Bx8 15 x 12 mm Rx8 Sx8 M6 M6 x 60 mm Insert part(R) into No.21 plate at first. Insert quickfit screw(S) into No.21 plate then. Attach No.20 plate to No.21, and turn cam lock(B) clockwise to tighten as shown.
14 Slide No.7 plate into available slots as shown.
15 Bx8 Rx8 Sx8 M6 M6 x 60 mm 15 x 12 mm Insert part(R) into No.22 plate at first. Insert quickfit screw(S) into No.22 plate then. Attach No.22 plate to No.20, and turn cam lock(B) clockwise to tighten as shown.
16 Dx8 Gx2 Hx2 M3.5 x 14 mm M4 M4 x 20 mm Ix4 DW Fix hinge(I) to No.21(x2) plate using screw(D) as shown. Fix knob(G) using screw(H).
17 D x 16 M3.5 x 14 mm Attach No.21 plate to No.4 and No.5 by fixing hinge with screw(D) as shown.
18 F x 16 M5 x 40 mm Connect No.10 and No.11 plate with No.12 using screw(F) as shown. Slide No.13 plate into available slots as shown.
19 A x 16 B x 16 M5 x 40 mm 15 x 12 mm Insert quickfit screw(A) into No.9 plate with a screwdriver as shown. Attach No.9 to No.10 and No.11 plate, turn cam lock(B) in No.10,11 plates clockwise to tighten as shown.
20 D x 16 M3.5 x 14 mm Fix No.15 runner to No.10 and No.11 plate using screw(D) as shown.
21 Dx2 Tx2 M3.5 x 14 mm M3.5 x 25 mm Lx2 Mx2 Fix part(L) to No.4,6 plate using screw(D) at first. Drill holes on wall, and knock part(M) into the wall, then fix part(L) to the wall using screw(T) as shown. Align rails, slide all drawers.
If there is misalignment after you install, adjust the screw to the best condition 27/27
