SAFETY DATA SHEET DDP Specialty Electronic Materials US, LLC Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Print Date: 05/11/2021 DDP Specialty Electronic Materials US, LLC encourages and expects you to read and understand the entire (M)SDS, as there is important information throughout the document. We expect you to follow the precautions identified in this document unless your use conditions would necessitate other appropriate methods or actions. 1.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Signal word: WARNING! Hazards Contains gas under pressure; may explode if heated. May cause an allergic skin reaction. Suspected of damaging fertility or the unborn child. May cause damage to organs (Kidney) through prolonged or repeated exposure if swallowed. May displace oxygen and cause rapid suffocation. Precautionary statements Prevention Obtain special instructions before use.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Triethyl phosphate 78-40-0 >= 1.0 - <= 10.0 % trans-1-Chloro-3,3,3-trifluoropropene 102687-65-0 >= 10.0 - <= 30.0 % Polyethylene glycol 25322-68-3 >= 1.0 - < 10.0 % Polyester polyol Not available Diethylene glycol 111-46-6 >= 1.0 - < 10.0 % Dimethylbis((1-oxoneodecyl)oxy)stannane 68928-76-7 >= 0.25 - < 1.0 % >= 20.0 - <= 80.0 % 4.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Unsuitable extinguishing media: Do not use direct water stream. May spread fire. Special hazards arising from the substance or mixture Hazardous combustion products: During a fire, smoke may contain the original material in addition to combustion products of varying composition which may be toxic and/or irritating. Combustion products may include and are not limited to: Carbon monoxide. Carbon dioxide. Hydrogen halides.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 7. HANDLING AND STORAGE Precautions for safe handling: Avoid contact with eyes. Avoid breathing vapor. Do not enter confined spaces unless adequately ventilated. Wash thoroughly after handling. Keep container closed. Use with adequate ventilation. This material is hygroscopic in nature. See Section 8, EXPOSURE CONTROLS AND PERSONAL PROTECTION.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Eye/face protection: Use safety glasses (with side shields). Where contact with the liquid is likely, chemical goggles are recommended. Skin protection Hand protection: Use gloves chemically resistant to this material. Examples of preferred glove barrier materials include: Chlorinated polyethylene. Polyethylene. Ethyl vinyl alcohol laminate ("EVAL"). Polyvinyl alcohol ("PVA"). Styrene/butadiene rubber. Viton.
Product name: FROTH-PAK(TM) POLYOL HFO Decomposition temperature Kinematic Viscosity Explosive properties No test data available No data available Not applicableNot explosive Oxidizing properties Molecular weight No data available No data available Issue Date: 02/23/2021 NOTE: The physical data presented above are typical values and should not be construed as a specification. 10. STABILITY AND REACTIVITY Reactivity: No data available Chemical stability: Stable under recommended storage conditions.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Serious eye damage/eye irritation Product test data not available. Refer to component data. Sensitization Product test data not available. Refer to component data. Specific Target Organ Systemic Toxicity (Single Exposure) Product test data not available. Refer to component data. Specific Target Organ Systemic Toxicity (Repeated Exposure) Product test data not available. Refer to component data. Carcinogenicity Product test data not available.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Sensitization Did not cause allergic skin reactions when tested in guinea pigs. For respiratory sensitization: No relevant data found. Specific Target Organ Systemic Toxicity (Single Exposure) Evaluation of available data suggests that this material is not an STOT-SE toxicant. Specific Target Organ Systemic Toxicity (Repeated Exposure) For similar active ingredient(s). In animals, effects have been reported on the following organs: Liver.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Specific Target Organ Systemic Toxicity (Single Exposure) Evaluation of available data suggests that this material is not an STOT-SE toxicant. Specific Target Organ Systemic Toxicity (Repeated Exposure) Based on available data, repeated exposures are not anticipated to cause significant adverse effects. Carcinogenicity No relevant data found. Teratogenicity Did not cause birth defects or any other fetal effects in laboratory animals.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Signs and symptoms of excessive exposure may be headache, dizziness, incoordination, muscle twitching, tremors, nausea, abdominal cramps, diarrhea, sweating, pinpoint pupils, blurred vision, salivation, tearing, tightness in chest, excessive urination, convulsions. Carcinogenicity No relevant data found. Teratogenicity No relevant data found.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 No relevant data found. Reproductive toxicity No relevant data found. Mutagenicity This material was not mutagenic in an Ames bacterial assay. Aspiration Hazard Based on available information, aspiration hazard could not be determined. Polyethylene glycol Acute oral toxicity Typical for this family of materials. LD50, Rat, > 10,000 mg/kg Estimated. Acute dermal toxicity Typical for this family of materials.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Reproductive toxicity In animal studies, did not interfere with reproduction. Mutagenicity In vitro genetic toxicity studies were negative. Animal genetic toxicity studies were negative. Aspiration Hazard Based on physical properties, not likely to be an aspiration hazard. Diethylene glycol Acute oral toxicity In humans, expected to be moderately toxic if swallowed even though oral toxicity was low when tested in animals.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Diethylene glycol has caused toxicity to the fetus and some birth defects at maternally toxic, high doses in animals. Other animal studies have not reproduced birth defects even at much higher doses that caused severe maternal toxicity. Reproductive toxicity Diethylene glycol did not interfere with reproduction in animal studies except at very high doses. Mutagenicity In vitro genetic toxicity studies were negative.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Aspiration Hazard No aspiration toxicity classification 12. ECOLOGICAL INFORMATION Ecotoxicological information appears in this section when such data is available. Toxicity 2-Ethylhexanoic acid potassium salt Acute toxicity to fish Based on information for a similar material: Material is slightly toxic to aquatic organisms on an acute basis (LC50/EC50 between 10 and 100 mg/L in the most sensitive species tested).
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 trans-1-Chloro-3,3,3-trifluoropropene Acute toxicity to fish Material is slightly toxic to aquatic organisms on an acute basis (LC50/EC50 between 10 and 100 mg/L in the most sensitive species tested).
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Material is moderately toxic to aquatic organisms on an acute basis (LC50/EC50 between 1 and 10 mg/L in the most sensitive species tested). EC50, Daphnia magna (Water flea), 48 Hour, 39 mg/l, OECD Test Guideline 202 Acute toxicity to algae/aquatic plants EC50, Pseudokirchneriella subcapitata (green algae), 72 Hour, 7.6 mg/l, OECD Test Guideline 201 NOEC, Pseudokirchneriella subcapitata (green algae), 72 Hour, 1.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Biodegradability: Material is not readily biodegradable according to OECD/EEC guidelines. Biodegradation: 0 % Exposure time: 28 d Method: OECD Test Guideline 301D Polyethylene glycol Biodegradability: Material is readily biodegradable. Passes OECD test(s) for ready biodegradability. 10-day Window: Pass Biodegradation: 85 % Exposure time: 28 d Method: OECD Test Guideline 301F or Equivalent Theoretical Oxygen Demand: 1.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Bioaccumulation: No relevant data found. Polyethylene glycol Partition coefficient: n-octanol/water(log Pow): -0.698 Pow: 0.2 at 30 °C Diethylene glycol Bioaccumulation: Bioaccumulation is unlikely. Partition coefficient: n-octanol/water(log Pow): -1.98 at 20 °C Bioconcentration factor (BCF): 100 Fish Measured Dimethylbis((1-oxoneodecyl)oxy)stannane Partition coefficient: n-octanol/water(log Pow): 5.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 INFORMATION PRESENTED HERE PERTAINS ONLY TO THE PRODUCT AS SHIPPED IN ITS INTENDED CONDITION AS DESCRIBED IN MSDS SECTION: Composition Information. FOR UNUSED & UNCONTAMINATED PRODUCT, the preferred options include sending to a licensed, permitted: Recycler. Reclaimer. Incinerator or other thermal destruction device.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Respiratory or skin sensitisation Specific target organ toxicity (single or repeated exposure) Superfund Amendments and Reauthorization Act of 1986 Title III (Emergency Planning and Community Right-to-Know Act of 1986) Section 313 This material does not contain any chemical components with known CAS numbers that exceed the threshold (De Minimis) reporting levels established by SARA Title III, Section 313.
Product name: FROTH-PAK(TM) POLYOL HFO US WEEL Issue Date: 02/23/2021 USA.
Product name: FROTH-PAK(TM) POLYOL HFO Issue Date: 02/23/2021 Page 23 of 23
SAFETY DATA SHEET DDP Specialty Electronic Materials US, LLC Product name: Froth-Pak™ ISO HFO cylinder Issue Date: 02/23/2021 Print Date: 05/06/2021 DDP Specialty Electronic Materials US, LLC encourages and expects you to read and understand the entire (M)SDS, as there is important information throughout the document. We expect you to follow the precautions identified in this document unless your use conditions would necessitate other appropriate methods or actions. 1.
Product name: Froth-Pak™ ISO HFO cylinder Issue Date: 02/23/2021 Signal word: DANGER! Hazards Contains gas under pressure; may explode if heated. Causes skin and eye irritation. May cause an allergic skin reaction. Harmful if inhaled. May cause allergy or asthma symptoms or breathing difficulties if inhaled. May cause respiratory irritation. May cause damage to organs (Respiratory Tract) through prolonged or repeated exposure if inhaled. May displace oxygen and cause rapid suffocation.
Product name: Froth-Pak™ ISO HFO cylinder This product is a mixture. Component Issue Date: 02/23/2021 CASRN Concentration Diphenylmethane Diisocyanate, isomers and homologues 9016-87-9 > 60.0 - <= 80.0 % 4,4' -Methylenediphenyl diisocyanate 101-68-8 > 20.0 - <= 40.0 % trans-1-Chloro-3,3,3-trifluoropropene 102687-65-0 > 0.0 - < 20.0 % Note Note: CAS 101-68-8 is an MDI isomer that is part of CAS 9016-87-9. 4.
Product name: Froth-Pak™ ISO HFO cylinder Issue Date: 02/23/2021 Notes to physician: Maintain adequate ventilation and oxygenation of the patient. May cause respiratory sensitization or asthma-like symptoms. Bronchodilators, expectorants and antitussives may be of help. Treat bronchospasm with inhaled beta2 agonist and oral or parenteral corticosteroids. Respiratory symptoms, including pulmonary edema, may be delayed.
Product name: Froth-Pak™ ISO HFO cylinder Issue Date: 02/23/2021 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures: Isolate area. Keep unnecessary and unprotected personnel from entering the area. Refer to section 7, Handling, for additional precautionary measures. Keep personnel out of low areas. Keep personnel out of confined or poorly ventilated areas. Keep upwind of spill. Ventilate area of leak or spill.
Product name: Froth-Pak™ ISO HFO cylinder trans-1-Chloro-3,3,3trifluoropropene US WEEL Issue Date: 02/23/2021 TWA 800 ppm Exposure controls Engineering controls: Use only with adequate ventilation. Local exhaust ventilation may be necessary for some operations. Provide general and/or local exhaust ventilation to control airborne levels below the exposure guidelines. Exhaust systems should be designed to move the air away from the source of vapor/aerosol generation and people working at this point.
Product name: Froth-Pak™ ISO HFO cylinder Flash point Evaporation Rate (Butyl Acetate = 1) Flammability (solid, gas) Lower explosion limit Upper explosion limit Vapor Pressure Relative Vapor Density (air = 1) Relative Density (water = 1) Water solubility Partition coefficient: noctanol/water Auto-ignition temperature Decomposition temperature Kinematic Viscosity Explosive properties Oxidizing properties Molecular weight Issue Date: 02/23/2021 > 200 °C ( > 392 °F) Not available Not expected to form explos
Product name: Froth-Pak™ ISO HFO cylinder Issue Date: 02/23/2021 Hazardous decomposition products: Decomposition products depend upon temperature, air supply and the presence of other materials. Gases are released during decomposition. 11. TOXICOLOGICAL INFORMATION Toxicological information appears in this section when such data is available. Acute toxicity Acute oral toxicity Product test data not available. Refer to component data. Acute dermal toxicity Product test data not available.
Product name: Froth-Pak™ ISO HFO cylinder Issue Date: 02/23/2021 Aspiration Hazard Product test data not available. Refer to component data. COMPONENTS INFLUENCING TOXICOLOGY: Diphenylmethane Diisocyanate, isomers and homologues Acute oral toxicity Typical for this family of materials. LD50, Rat, > 10,000 mg/kg Acute dermal toxicity Typical for this family of materials. LD50, Rabbit, > 9,400 mg/kg Acute inhalation toxicity LC50, Rat, 4 Hour, dust/mist, 0.
Product name: Froth-Pak™ ISO HFO cylinder Issue Date: 02/23/2021 LD50, Rat, > 2,000 mg/kg No deaths occurred at this concentration. Acute dermal toxicity LD50, Rabbit, > 9,400 mg/kg Acute inhalation toxicity LC50, Rat, 1 Hour, dust/mist, 2.24 mg/l Skin corrosion/irritation Prolonged contact may cause moderate skin irritation with local redness. Repeated contact may cause moderate skin irritation with local redness. May stain skin. Serious eye damage/eye irritation May cause moderate eye irritation.
Product name: Froth-Pak™ ISO HFO cylinder Issue Date: 02/23/2021 Sensitization Did not cause allergic skin reactions when tested in humans. For respiratory sensitization: No relevant data found. Specific Target Organ Systemic Toxicity (Single Exposure) Evaluation of available data suggests that this material is not an STOT-SE toxicant. Reproductive toxicity No relevant data found. Aspiration Hazard Based on available information, aspiration hazard could not be determined. 12.
Product name: Froth-Pak™ ISO HFO cylinder Issue Date: 02/23/2021 EC50, Lactuca sativa (lettuce), Growth inhibition, 1,000 mg/l 4,4' -Methylenediphenyl diisocyanate Acute toxicity to fish The measured ecotoxicity is that of the hydrolyzed product, generally under conditions maximizing production of soluble species. Material is practically non-toxic to aquatic organisms on an acute basis (LC50/EC50/EL50/LL50 >100 mg/L in the most sensitive species tested).
Product name: Froth-Pak™ ISO HFO cylinder Issue Date: 02/23/2021 environment, material is expected to have a short tropospheric half-life, based on calculations and by analogy with related diisocyanates.
Product name: Froth-Pak™ ISO HFO cylinder Issue Date: 02/23/2021 13. DISPOSAL CONSIDERATIONS Disposal methods: DO NOT DUMP INTO ANY SEWERS, ON THE GROUND, OR INTO ANY BODY OF WATER. All disposal practices must be in compliance with all Federal, State/Provincial and local laws and regulations. Regulations may vary in different locations. Waste characterizations and compliance with applicable laws are the responsibility solely of the waste generator.
Product name: Froth-Pak™ ISO HFO cylinder Issue Date: 02/23/2021 15.
Product name: Froth-Pak™ ISO HFO cylinder Issue Date: 02/23/2021 Revision Identification Number: 12074990 / A749 / Issue Date: 02/23/2021 / Version: 2.1 Most recent revision(s) are noted by the bold, double bars in left-hand margin throughout this document. Legend ACGIH C Dow IHG OSHA Z-1 STEL TWA US WEEL USA. ACGIH Threshold Limit Values (TLV) Ceiling Dow Industrial Hygiene Guideline USA. Occupational Exposure Limits (OSHA) - Table Z-1 Limits for Air Contaminants Short term exposure limit 8-hr TWA USA.
Product name: Froth-Pak™ ISO HFO cylinder Issue Date: 02/23/2021 DDP Specialty Electronic Materials US, LLC urges each customer or recipient of this (M)SDS to study it carefully and consult appropriate expertise, as necessary or appropriate, to become aware of and understand the data contained in this (M)SDS and any hazards associated with the product. The information herein is provided in good faith and believed to be accurate as of the effective date shown above.
FICHA DE DATOS DE SEGURIDAD DDP Specialty Electronic Materials US, LLC Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Fecha de impresión: 05/11/2021 DDP Specialty Electronic Materials US, LLC le ruega que lea atentamente esta Hoja de Datos de Seguridad (HDS) y espera que entienda todo su contenido ya que contiene información importante. Esperamos que siga las precauciones indicadas en este documento, a menos que las condiciones de uso necesiten otros métodos o acciones. 1.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Palabra de advertencia: ATENCIÓN¡ Peligros Contiene gas a presión; peligro de explosión en caso de calentamiento. Puede provocar una reacción alérgica en la piel. Se sospecha que puede perjudicar la fertilidad o dañar el feto. Puede provocar daños en los órganos (Riñón) tras exposiciones prolongadas o repetidas en caso de ingestión. Puede desplazar al oxígeno y causar asfixia rápida.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Fosfato de tris (1-cloro-2 propil) 13674-84-5 >= 10.0 - <= 30.0 % Trietil-fosfato 78-40-0 >= 1.0 - <= 10.0 % Trans - 1 - cloro - 3,3,3 - trifluoropropeno 102687-65-0 >= 10.0 - <= 30.0 % Polietilenglicol 25322-68-3 >= 1.0 - < 10.0 % Poliol poliéster Not available Dietilenglicol 111-46-6 >= 1.0 - < 10.0 % Estanato Dimetilbis{(1-oxoneodecil)oxi} 68928-76-7 >= 0.25 - < 1.0 % >= 20.0 - <= 80.0 % 4.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Notas para el médico: Mantener un grado adecuado de ventilación y oxigenación del paciente. Si la respiración es dificultosa, se deberá administrar oxígeno por personal cualificado. El tratamiento de la exposición se dirigirá al control de los síntomas y a las condiciones clínicas del paciente. 5. MEDIDAS DE LUCHA CONTRA INCENDIOS Medios de extinción apropiados: Niebla o agua pulverizada/atomizada. Extintores de polvo químico.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 6. MEDIDAS EN CASO DE VERTIDO ACCIDENTAL Precauciones personales, equipo de protección y procedimientos de emergencia: Aislar el área. Mantener fuera del área al personal no necesario y sin protección. Mantener a las personas fuera de las áreas confinadas o poco ventiladas. Mantenerse a contraviento del derrame. El producto derramado puede ocasionar un riesgo de caída por suelo resbaladizo. Ventilar el área de pérdida o derrame.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Estanato Dimetilbis{(1oxoneodecil)oxi} Fecha: 02/23/2021 OSHA Z-1 TWA 0.1 mg/m3 , Estaño ACGIH TWA 0.1 mg/m3 , Estaño Otros datos: A4: No clasificados como cancerigenos en humanos; Skin: Riesgo de absorción cutánea ACGIH STEL 0.2 mg/m3 , Estaño Otros datos: A4: No clasificados como cancerigenos en humanos; Skin: Riesgo de absorción cutánea CAL PEL PEL 0.1 mg/m3 , Estaño STEL 0.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Estado físico Color Olor Umbral olfativo pH Punto/intervalo de fusión Punto de congelación Punto de ebullición (760 mmHg) Punto de inflamación Velocidad de Evaporación ( Acetato de Butilo = 1) Inflamabilidad (sólido, gas) Límites inferior de explosividad Límite superior de explosividad Presión de vapor: Densidad de vapor relativa (aire=1) Densidad Relativa (agua = 1) Solubilidad en agua Coeficiente de reparto noctanol/agua Temperatura de auto-inflamación Temper
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Materiales incompatibles: Evite el contacto con los materiales oxidantes. Evitar el contacto con: Ácidos fuertes. Bases fuertes. Evite el contacto accidental con isocianatos. Lareacción entre los polioles e isocianatos genera calor. Productos de descomposición peligrosos: Los productos de descomposición dependen de la temperatura, el suministro de aire y la presencia de otros materiales.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Peligro de Aspiración Los datos de prueba del producto no está disponible. Consulte los datos de componentes. COMPONENTES INFLUYENDO LA TOXICOLOGÍA: Sal potásica de ácido 2-etil hexanoico Toxicidad oral aguda Basado en informaciones sobre un producto similar. DL50, Rata, hembra, 2,043 mg/kg Directrices de ensayo 401 del OECD Toxicidad cutánea aguda Basado en informaciones sobre un producto similar.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Toxicidad para la reproducción Para materiales similares(s): En estudios realizados sobre animales de laboratorio, sólo se han demostrado efectos en la reproducción a dosis que también produjeron toxicidad importante en los progenitores. Mutagénicidad Para materiales similares(s): Los estudios de toxicidad genética in Vitro han dado resultados negativos. Los estudios de toxicidad genética con animales dieron resultados negativos.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Los estudios de toxicidad genética in Vitro han dado resultados negativos. Los estudios de toxicidad genética con animales dieron resultados negativos. Peligro de Aspiración En base a la información disponible, no se ha podido determinar el riesgo de aspiración.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Mutagénicidad Los estudios de toxicidad genética ¨in Vitro¨ dieron resultados principalmente negativos. Los estudios de toxicidad genética sobre animales han dado resultados principalmente negativos. Peligro de Aspiración Sobre la base de las propiedades físicas, no es probable el riesgo de aspiración. Trans - 1 - cloro - 3,3,3 - trifluoropropeno Toxicidad oral aguda No se ha determinado el DL50 por ingestión de una única dosis oral.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Toxicidad cutánea aguda Típico para esta familia de materiales. DL50, Conejo, > 20,000 mg/kg Toxicidad aguda por inhalación Típico para esta familia de materiales. CL50, Rata, 6 h, polvo/niebla, > 2.5 mg/l No hubo mortandad con esta concentración. Corrosión o irritación cutáneas No es probable que por una exposición prolongada o repetida se irrite la piel de modo significativo.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Dietilenglicol Toxicidad oral aguda En el caso de seres humanos, la ingestión debería ser moderada aunque la toxicidad oral fue baja cuando se experimentó con animales. Ingestión de cantidades, aproximadamente 65 ml (2 oz.) del dietilenglicol o 100 ml (3 oz.) del etilenglicol, ha causado muerte en seres humanos. Puede provocar náuseas o vómitos. Puede causar molestias abdominales o diarrea.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Mutagénicidad Los estudios de toxicidad genética in Vitro han dado resultados negativos. Los estudios de toxicidad genética con animales dieron resultados negativos. Peligro de Aspiración Ninguna clasificación de toxicidad por aspiración Estanato Dimetilbis{(1-oxoneodecil)oxi} Toxicidad oral aguda DL50, Rata, 892 mg/kg Toxicidad cutánea aguda No se ha determinado el DL50 por vía cutánea.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 12. INFORMACIÓN ECOLÓGICA Información ecotoxicológica aparece en esta sección cuando tales datos están disponibles. Toxicidad Sal potásica de ácido 2-etil hexanoico Toxicidad aguda para peces Basado en informaciones sobre un producto similar. El producto es ligeramente tóxico para los organismos acuáticos en una dosis aguda (CL50/CE50 varia entre 10 y 100 mg/l para las especies ensayadas más sensibles).
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Toxicidad aguda para peces El producto es ligeramente tóxico para los organismos acuáticos en una dosis aguda (CL50/CE50 varia entre 10 y 100 mg/l para las especies ensayadas más sensibles).
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 El producto es moderadamente tóxico para los organismos acuáticos en dosis agudas (CL50/CE50 varía entre 1 y 10 mg/l para la mayoría de las especies más sensibles ensayadas). CE50, Daphnia magna (Pulga de mar grande), 48 h, 39 mg/l, Directrices de ensayo 202 del OECD Toxicidad aguda para las algas/plantas acuáticas CE50, Pseudokirchneriella subcapitata (alga verde), 72 h, 7.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Demanda Teórica de Oxígeno: 1.58 mg/mg Trans - 1 - cloro - 3,3,3 - trifluoropropeno Biodegradabilidad: El producto no es fácilmente degradable según las Directrices de la OCDE/EC. Biodegradación: 0 % Tiempo de exposición: 28 d Método: Directrices de ensayo 301D del OECD Polietilenglicol Biodegradabilidad: El material es fácilmente biodegradable. Pasa los ensayos OECD de fácil biodegradabilidad.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Bioacumulación: El potencial de bioconcentración es bajo (FBC < 100 o Log Pow < 3). Coeficiente de reparto n-octanol/agua(log Pow): 0.80 medido Trans - 1 - cloro - 3,3,3 - trifluoropropeno Bioacumulación: No se encontraron datos relevantes. Polietilenglicol Coeficiente de reparto n-octanol/agua(log Pow): -0.698 Pow: 0.2 a 30 °C Dietilenglicol Bioacumulación: La bioacumulación es improbable. Coeficiente de reparto n-octanol/agua(log Pow): -1.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 13. CONSIDERACIONES RELATIVAS A LA ELIMINACIÓN Métodos de eliminación.: NO ENVIAR A NINGUN DESAGÜE, NI AL SUELO NI A NINGUNA CORRIENTE DE AGUA. Todas las prácticas de vertido deben cumplir las Leyes y Reglamentos Federales, Estatales, Provinciales y Locales. Los reglamentos pueden variar según la localización. El generador de los residuos es el único responsable de la caracterización de los mismos y del cumplimiento de las Leyes aplicables.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Esta información no pretende abarcar toda la información/requisitos legislativos específicos u operacionales del producto. Las clasificaciones para el transporte pueden variar en función del volumen del contenedor y de las diferentes normativas regionales o nacionales. La información adicional sobre el sistema de transporte puede obtenerse a través de un representante autorizado de la organización de ventas o servicio de atención al cliente.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 Sistema de Clasificación de Peligros HMIS Salud Inflamabilidad Peligro Físico 2* 1 3 * = Efectos crónicos (véase la Identificación delos Peligros) Revisión Número de Identificación: / A749 / Fecha: 02/23/2021 / Versión: 1.1 Las revisiones más recientes están marcadas con doble barra y negrita en el margen izquierdo del documento.
Nombre del producto: FROTH-PAK(TM) POLYOL HFO Fecha: 02/23/2021 autoacelerada; SARA - Ley de Enmiendas y Reautorización de Superfondos; SDS - Ficha de datos de seguridad; TCSI - Inventario de Sustancias Químicas de Taiwán; TSCA - Ley para el Control de Sustancias Tóxicas (Estados Unidos); UN - Naciones Unidas; UNRTDG - Recomendaciones de las Naciones Unidas sobre el transporte de mercancías peligrosas; vPvB - Muy persistente y muy bioacumulativo Fuentes y referencias de la información.
FICHA DE DATOS DE SEGURIDAD DDP Specialty Electronic Materials US, LLC Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 Fecha de impresión: 05/06/2021 DDP Specialty Electronic Materials US, LLC le ruega que lea atentamente esta Hoja de Datos de Seguridad (HDS) y espera que entienda todo su contenido ya que contiene información importante. Esperamos que siga las precauciones indicadas en este documento, a menos que las condiciones de uso necesiten otros métodos o acciones. 1.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 Palabra de advertencia: PELIGRO¡ Peligros Contiene gas a presión; peligro de explosión en caso de calentamiento. Provoca irritación cutánea y ocular. Puede provocar una reacción alérgica en la piel. Nocivo en caso de inhalación. Puede provocar síntomas de alergia o asma o dificultades respiratorias en caso de inhalación. Puede irritar las vías respiratorias.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 3. COMPOSICIÓN/INFORMACIÓN SOBRE LOS COMPONENTES Este producto es una mezcla. Componente Número de registro CAS Concentración Diisocianato de difenilmetano, isómeros y homólogos 9016-87-9 > 60.0 - <= 80.0 % 4,4´-metilendifenil diisocianato 101-68-8 > 20.0 - <= 40.0 % Trans - 1 - cloro - 3,3,3 - trifluoropropeno 102687-65-0 > 0.0 - < 20.0 % Nota Nota: CAS 101-68-8 es un isómero de MDI parte deCAS 9016-87-9. 4.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 Además de la información detallada en los apartados Descripción de los primeros auxilios (anteriormente) e Indicación de toda atención médica y de los tratamientos especiales que deban dispensarse inmediatamente (a continuación); la Sección 11: Información toxicológica incluye la descripción de algunos síntomas y efectos adicionales.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 dispositivo de seguridad o si nota un cambio de color en el contenedor. Mueva el contenedor del área de incendio si estamaniobra no comporta peligro alguno. Usar agua pulverizada para enfriar los contenedores expuestos al fuego y la zona afectada por el mismo, hasta que el incendio se haya extinguido. Contener la expansión del agua de la extinción si es posible. Puede causar un daño medioambiental si no se contiene.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 Condiciones para el almacenaje seguro: Minimizar las fuentes de ignición, tales como laacumulación de carga estática, calor, chispas o llamas. En algunas situaciones de almacenamiento, se pueden acumular vapores inflamables. Proteger de la humedad atmosférica. Almacenar en un lugar seco. Evite la exposición prolongada al calor y aire. Evitar las temperaturas superiores a 50°C (122°F) Ver Sección 10 para información más específica.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 orgánicos. En situaciones en las que las concentraciones atmosféricas pueden exceder el nivel para el que son efectivos respiradores purificadores de aire, utilizar respiradores con suministro de aire a presión positiva (equipo respiratorio semiautónomo o autónomo).
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 10. ESTABILIDAD Y REACTIVIDAD Reactividad: Sin datos disponibles Estabilidad química: Estable en las condiciones de almacenamiento recomendadas. Ver Almacenaje, sección 7. Posibilidad de reacciones peligrosas: Puede suceder. Las temperaturas elevadas pueden ocasionar una polimerización peligrosa. La polimerización se puede catalizar por: Bases fuertes. Agua.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 Corrosión o irritación cutáneas Los datos de prueba del producto no está disponible. Consulte los datos de componentes. Lesiones o irritación ocular graves Los datos de prueba del producto no está disponible. Consulte los datos de componentes. Sensibilización Los datos de prueba del producto no está disponible. Consulte los datos de componentes.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 Para materiales similares(s): Diisocianato de 4,4'-Metilendifenil (CAS 101-68-8). CL50, Rata, 1 h, Aerosol, 2.24 mg/l Para materiales similares(s): Diisocianato de 2,4'-Difenilmetano (CAS 5873-54-1). CL50, Rata, 4 h, Aerosol, 0.387 mg/l Corrosión o irritación cutáneas Una exposición prolongada puede causar una leve irritación en la piel con enrojecimiento local. Puede manchar la piel.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 Lesiones o irritación ocular graves Puede producir una irritación moderada en los ojos. Puede producir una ligera lesión transitoria (temporal) de la córnea. Sensibilización El contacto con la piel puede producir una reacción alérgica cutánea. Estudios en animales han mostrado que el contacto cutáneo juega un papel en la sensibilización respiratoria. Puede causar una reacción respiratoria alérgica.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 Toxicidad para la reproducción No se encontraron datos relevantes. Peligro de Aspiración En base a la información disponible, no se ha podido determinar el riesgo de aspiración. 12. INFORMACIÓN ECOLÓGICA Información ecotoxicológica aparece en esta sección cuando tales datos están disponibles.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 CL50, Danio rerio (pez zebra), Ensayo estático, 96 h, > 1,000 mg/l, Guía de ensayos de la OCDE 203 o Equivalente Toxicidad aguda para invertebrados acuáticos Basado en informaciones sobre un producto similar. CE50, Daphnia magna (Pulga de mar grande), Ensayo estático, 24 h, > 1,000 mg/l, Guía de ensayos de la OCDE 202 o Equivalente Toxicidad aguda para las algas/plantas acuáticas Basado en informaciones sobre un producto similar.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 Biodegradabilidad: En los ambientes acuático y terrestre, el material reacciona con agua formando predominantemente poliureas insolubles que parecen ser estables. En ambiente atmosférico, se estima que el material tendrá una vida media troposférica corta, basándose en cálculos y por analogía con diisocianatos similares.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 13. CONSIDERACIONES RELATIVAS A LA ELIMINACIÓN Métodos de eliminación.: NO ENVIAR A NINGUN DESAGÜE, NI AL SUELO NI A NINGUNA CORRIENTE DE AGUA. Todas las prácticas de vertido deben cumplir las Leyes y Reglamentos Federales, Estatales, Provinciales y Locales. Los reglamentos pueden variar según la localización.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 Esta información no pretende abarcar toda la información/requisitos legislativos específicos u operacionales del producto. Las clasificaciones para el transporte pueden variar en función del volumen del contenedor y de las diferentes normativas regionales o nacionales.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 16. OTRA INFORMACIÓN Sistema de Clasificación de Peligros HMIS Salud Inflamabilidad Peligro Físico 2* 1 3 * = Efectos crónicos (véase la Identificación delos Peligros) Revisión Número de Identificación: 12074990 / A749 / Fecha: 02/23/2021 / Versión: 2.1 Las revisiones más recientes están marcadas con doble barra y negrita en el margen izquierdo del documento.
Nombre del producto: Froth-Pak™ ISO HFO cylinder Fecha: 02/23/2021 Parlamento Europeo y del Consejo relativo al registro, la evaluación, la autorización y la restricción de las sustancias químicas; RQ - Cantidad reportable; SADT - Temperatura de descomposición autoacelerada; SARA - Ley de Enmiendas y Reautorización de Superfondos; SDS - Ficha de datos de seguridad; TCSI - Inventario de Sustancias Químicas de Taiwán; TSCA - Ley para el Control de Sustancias Tóxicas (Estados Unidos); UN - Naciones Unidas; U