Installation Instructions

ManualsBrandsFrigidaire ManualsSingle Oven Electric RangesSmooth Surface 5-cu ft Steam Cleaning Freestanding Electric Range (EasyCare Stainless Steel) (Common: 30-in; Actual: 29.875-in)

INSTALLATION INSTRUCTIONS

FRONT CONTROL FREESTANDING ELECTRIC RANGE

INSTALLATION AND SERVICE MUST BE

PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

IMPORTANT SAFETY INSTRUCTIONS

If the information in this manual is not followed

exactly, a re or electrical shock may result causing property

damage, personal injury or death.

Important Notes to the Installer:

• Read all instructions contained in these installation

instructions before installing range.

• Remove all packing material from the oven

compartments before connecting the gas & electrical

supply to the range.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the

consumer.

Important Notes to the Consumer:

Keep these instructions with your owner’s guide for future

reference.

• As when using any appliance generating heat, there

are certain safety precautions you should follow.

These are listed in the Use & Care Guide, read it

carefully.

• Be sure your range is installed and grounded properly

by a qualied installer or service technician.

• Make sure the wall coverings around the range can

withstand the heat generated by the range.

• To eliminate the need to reach over the surface

elements, cabinet storage space above the elements

should be avoided.

Tip Over Hazard

Range

leveling leg

Anti-tip

bracket

• A child or adult can tip the

range and be killed.

• Verify the anti-tip device has

been installed to floor or wall.

• Ensure the anti-tip device is re-engaged to floor

or wall when the range is moved.

• Do not operate the range without the anti-tip

device in place and engaged.

• Failure to follow these instructions can result in

death or serious burns to children and adults.

To check if the anti-tip bracket is installed properly, use

both arms to grasp the rear edge of the range back.

Carefully attempt to tilt range forward. When properly

installed, the range should not tilt forward.

Refer to the anti-tip bracket installation instructions

supplied with your range for proper installation.

FOR YOUR SAFETY: Do not store or use gasoline

or other ammable vapors and liquids in the vicinity of this or

any other appliance.

United States

P/N 809127105 (1901) Rev. B

English – pages 1-8

Spanish - pages 9-16

Summary of content (16 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FRONT CONTROL FREESTANDING ELECTRIC RANGE INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. United States FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
PAGE 2
30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS 1. Clearances and Dimensions a. Provide adequate clearances between the range and adjacent combustible surfaces. b. Location—Check location where the range will be installed. Check for proper electrical supply and the stability of floor. c. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid and level.
PAGE 3
0” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS 2. Tools You Will Need If rear of range is further than 1-1/4" (32 mm) from the wall when installed, attach bracket to the floor. For floor mount, locate the bracket by placing back edge of the template where the rear of the range will be located. Mark the location of the screw holes, shown in template.
PAGE 4
30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS Models requiring power supply cord kit C. Level and Position Range - Level range by adjusting the (4) leveling legs with a wrench. Note: Aminimum clearance of 1/8” (3 mm) is required between the bottom of the range and the leveling leg to allow room for the bracket. Use a spirit level to check your adjustments. Slide range back into position.
PAGE 5
30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS Fig. 10 NOTE: Internal white wire not present on all models. Fig. 12 5B. POWER CORD CONNECTIONS (3-Wire Connection Instructions For existing installations ONLY - Refer to Fig. 13). Fig. 11 1. Follow the manufacturer’s installation instructions supplied with the strain relief and install (Also see Figs. 9, 10 & 11). 2. Insert the end connectors for Line 1, Line 2 and Neutral and tighten securely to the terminal block (See Fig. 13).
PAGE 6
30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS 6. Carefully Slide Range Into Final Location Grounding Instructions (3-Wire Connections only) A ground strap is installed on this range which connects the center terminal of the terminal block (Neutral) to the range chassis. The ground strap is connected to the range by the center, lowest screw (See Fig. 13). The ground strap must not be removed unless National, State or Local Codes do not permit use of a ground strap.
PAGE 7
30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS 7. Install filler trim kit Note: Installation of the filler trim kit is not required. Disconnect electrical power to range before beginning installation. Before servicing any part of the appliance, make sure the appliance is off and the surfaces are cool. Attempting to service the appliance while hot may cause burns or other injury. Filler Trim Attachment Instructions: Fig. 19 - Range with filler trim installed. 1.
PAGE 8
30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS 8. Model and Serial Number Location Some models have a cool-air intake vent on the rear of the appliance. Do not block or obstruct this vent. The serial plate is located on the right-hand surface of the oven front frame at the storage or warmer drawer; or the lower panel area.
PAGE 9
INSTRUCCIONES DE INSTALACION LA ESTUFA ELECTRICA DE 30” LA INSTALACION Y EL SERVICIO DEBEN SER EFECTUADOS POR UN INSTALADOR CALIFICADO. IMPORTANTE: CONSERVE ESTAS INSTRUCCIONES PARA USO DEL INSPECTOR LOCAL DE ELECTRICIDAD. LEA Y CONSERVE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA. Estados Unidos PARA SU SEGURIDAD: No almacene ni use gasolina u otros vapores y líquidos inflamables cerca de este o cualquier otro electrodoméstico.
PAGE 10
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30” 1. Espacios y dimensiones a. Proporcione espacios adecuados entre la estufa y las superficies combustibles adyacentes. b. Ubicación—Examine el lugar en el cual va a ser instalada la estufa. Determine la existencia de suministro eléctrico adecuado y la estabilidad del piso. c. Se deben usar las medidas indicadas. Las dimensiones indicadas proporcionan espacio mínimo.
PAGE 11
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30” 2. Herramientas que va a necesitar pared. Si la parte trasera de la estufa está a más de 1-1/4” de la pared cuando ya está instalada, instale el soporte en el piso. Para el montaje en el piso, ubique el soporte colocando el borde trasero de la plantilla donde quedará ubicada la parte trasera de la estufa. Marque la ubicación de los agujeros de los tornillos mostrados en la plantilla.
PAGE 12
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30” Modelos que requieren Juego de Cordón para el Suministro de Energía C. Nivele y ubique la estufa - Nivele la estufa ajustando los cuatro (4) tornillos niveladores con una llave. Nota: Se debe dejar un espacio libre mínimo de 1/8” (3 mm) entre la parte inferior de la estufa y los tornillos niveladores a fin de dejar espacio para instalar el soporte. Use un nivel de burbuja de aire para verificar los ajustes. Deslice la estufa de nuevo a su lugar.
PAGE 13
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30” Conexión Tetrafilar Tabla del Tamaño de la Abertura de Conexión de la Estufa Conexiones instaladas en la fábrica (NO AFLOJAR) Informació sobre la potencia nominal en amperios del Juego de Cable de Alimentación. Ver la placa de serie en la estufa para los datos sobre la potencia nominal en kilovatios.
PAGE 14
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30” 6. DESLICE CON CUIDADO LA ESTUFA HASTA SU LUGAR DEFINITIVO Instrucciones para la Puesta a Tierra (para conexiones trifilares solamente) Esta estufa tiene instalada una cinta de conexión a tierra que conecta el borne central del tablero de bornes (neutro) al chasis de la estufa. La cinta de conexión a tierra está conectada a la estufa mediante el tornillo central más inferior (Ver Fig. 13).
PAGE 15
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30” 15. Instalar kit de ajuste de relleno Nota: no es necesario instalar el kit de acabado de relleno. Corte la alimentación eléctrica de la estufa entes de instalar. Antes de realizar cualquier operación de servicio con el electrodoméstico, asegúrese de que está desconectado y que las superficies están frías. Si intenta realizar una operación de servicio con el electrodoméstico caliente, puede sufrir quemaduras u otras lesiones. Fig.
PAGE 16
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30” 7. Ubicación del modelo y número de serie Algunos modelos tienen un respiradero de admisión de aire frío en la parte posterior del aparato. No bloquee u obstruya esta ventilación. La placa de serie está ubicada en la superficie derecha del marco frontal del horno en el cajón de almacenamiento o calentador; o el área del panel inferior.