Owner's Guide

5
OPERATING INSTRUCTIONS
Sanitize Option
To sanitize your dishes and glassware, select
SANITIZE option. When selected, the light
above the pad will come on and remain on until
end of cycle. The water temperature in the
fi nal rinse will be raised to 155
o
F (68
o
C) and will
maintain that temperature for 9 minutes. This
option is available in Heavy and Normal Clean
Cycles. Only these sanitization cycles have
been designed to meet NSF requirements.
The cycle time will be extended until the proper
water temperature is reached.
Washing
action will continue during the water heating
delay. For best results, the incoming water
temperature should be at least 120
o
F (49
o
C).
The sanitize criteria may not be satisfi ed if there
is an interruption of the cycle, power failure or if
the incoming water temperature is below 120
o
F
(49
o
C).
To turn off the SANITIZE option, press the pad
a second time. The light above the pad will
turn off.
Delay Start
Heat Dry/Air Dry
Use the HEAT DRY option, especially in
combination with use of rinse agent, will
enhance drying. If AIR DRY is selected the
heater will be de-activated during the drying
phase of the selected wash cycle. This will
slightly lower the energy use but will increase
the likelihood that the dishware will not dry
completely.
Child Lock Controls
To prevent children from accidently changing
the dishwasher cycle or starting the
dishwasher, lock the dishwasher controls
by pressing and releasing the AIR DRY pad
for 3 seconds while the door is latched. An
indicator light on the lock graphic pad will
illuminate when the controls are locked and
no new selections can be made until the lock
is released. To unlock the controls, press the
same pad, AIR DRY, until the indicator light
goes out.
To Cancel a Cycle
Option Selections
Hi-Temp Wash Option
When HI-TEMP WASH option is selected, the
dishwasher heats water in the main wash to
approximately 140
o
F (60
o
C).
This increase in water temperature helps the
dishwasher detergent remove food grease and
soil from dishes more effectively and aids in
drying. HI-TEMP WASH option can be used
with HEAVY and NORMAL CLEAN only. HI-TEMP
WASH is automatically provided when the
HEAVY CLEAN cycle is selected.
When HI-TEMP WASH option is selected, the
light above the pad will come on and remain
on until end of cycle. To turn off the HI-TEMP
WASH option, press the pad a second time.
The light above the pad will turn off.
The DELAY START option allows you to
automatically delay starting your dishwasher
for either 2-4-6 hours.
To activate delay start option for 2-4-6 hour
delay, press the pad once for a 2 hour delay,
twice for 4 hours and three times for 6 hours.
A light will come on indicating the delay start
hours and will remain on until cycle starts.
Press the START/PAUSE pad to start the delay
option. If the delay option is interrupted, the
START/PAUSE pad will have to be pressed
again to return to delay option.
To cancel the DELAY START option and begin
the cycle before the delay period is over, press
the CANCEL pad.
You can cancel a cycle anytime during the cycle.
Press the CANCEL pad and dishwasher will start
a 90 second drain. At the end of the drain,
select the next desired cycle.
Status Indicator Lights
When the SANITIZE option is selected, the
SANITIZED light will glow when the SANITIZE
cycle is fi nished. If the dishwasher did not
properly sanitize the dishes, the light will not
come on. This can happen if the cycle is
interrupted. The light will remain on until the
door is opened.
The CLEAN light will come on at the end of
cycle and remain on until the door is opened.
The WASHING light comes on at the beginning
of the cycle and remains on until the end of
the main wash.