Installation Manual

ManualsBrandsFrigidaire ManualsKitchen Appliance PackageFrigidaire FRRERADWMW12116

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Clearances and Dimensions

1. Provide adequate clearances between the range and adjacent combustible surfaces.

2. Location—Check location where the range will be installed. Check for proper electrical supply, and the stability of the oor.

3. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid and level.

*30" MINIMUM CLEARANCE BETWEEN THE TOP OF THE COOKING SURFACE AND THE BOTTOM OF AN UNPROTECTED WOOD OR

METAL CABINET; OR 24" MINIMUM WHEN BOTTOM OF WOOD OR METAL CABINET IS PROTECTED BY NOT LESS THAN 1/4" FLAME

RETARDANT MILLBOARD COVERED WITH NOT LESS THAN NO. 28 MSG SHEET STEEL, 0.015" STAINLESS STEEL, 0.024" ALUMINUM

OR 0.020" COPPER. 0" CLEARANCE IS THE MINIMUM FOR THE REAR OF THE RANGE. FOLLOW ALL DIMENSION REQUIREMENTS

PROVIDED ABOVE TO PREVENT PROPERTY DAMAGE, POTENTIAL FIRE HAZARD, AND INCORRECT COUNTERTOP AND CABINET

CUTS.

TO ELIMINATE THE RISK OF BURNS OR FIRE BY REACHING OVER HEATED SURFACE UNITS, CABINET STORAGE SPACE

LOCATED ABOVE THE SURFACE UNITS SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE PROVIDED, THE RISK CAN BE

REDUCED BY INSTALLING A RANGE HOOD THAT PROJECTS HORIZONTALLY A MINIMUM OF 5" BEYOND THE BOTTOM OF THE

CABINETS.

p/n 316454912 rev E

30"

25-3/4”

49”

48”

29 1/4” with

door handle

maximum

door open

maximum

Fig. 1

Fig. 2 Fig. 3

Important Notes to the Consumer:

Keep these instructions with your owner's guide for future

reference.

• As when using any appliance generating heat, there are

certain safety precautions you should follow. These are

listed in the Use & Care Guide, read it carefully.

• Be sure your range is installed and grounded properly by

a qualied installer or service technician.

• Make sure the wall coverings around the range can

withstand the heat generated by the range.

• To eliminate the need to reach over the surface elements,

cabinet storage space above the elements should be

avoided.

IMPORTANT SAFETY INSTRUCTIONS

INSTALLATION INSTRUCTIONS FOR FREESTANDING ELECTRIC RANGE

Español - Páginas 5-8

• Ensure the anti-tip device is re-engaged when the range

is moved to oor or wall.

• Do not operate the range without the anti-tip device in

place and engaged.

• Failure to follow these instructions can result in death or

serious burns to children and adults.

Tip Over Hazard

To check if the anti-tip bracket is installed properly, use

both arms and grasp the rear edge of range back. Carefully

attempt to tilt range forward. When properly installed, the

range should not tilt forward.

Refer to the anti-tip bracket installation instructions

supplied with your range for proper installation.

Range

leveling leg

Anti-Tip

bracket

• A child or adult can tip the range and

be killed.

• Verify the anti-tip device has been

installed to oor or wall.

If the information in this manual is not followed

exactly, a re or electrical shock may result causing property

damage, personal injury or death.

Important Notes to the Installer:

• Read all instructions contained in these installation

instructions before installing range.

• Remove all packing material from the oven compartments

before connecting the gas & electrical supply to the range.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the consumer.

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR FREESTANDING ELECTRIC RANGE INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Clearances and Dimensions 1. Provide adequate clearances between the range and adjacent combustible surfaces. 2. Location—Check location where the range will be installed. Check for proper electrical supply, and the stability of the floor. 3.
PAGE 2
INSTALLATION INSTRUCTIONS FOR FREESTANDING ELECTRIC RANGE If bracket is to be mounted to masonry or ceramic floors, drill a 3/16" pilot hole 1-3/4" deep. The screws provided may be used in wood or concrete material. Use a 5/16" nut-driver or flat head screwdriver to secure the bracket in place (See Fig. 6). 1c. Level and Position Range - Level range by adjusting the (4) leveling legs with a wrench.
PAGE 3
INSTALLATION INSTRUCTIONS FOR FREESTANDING ELECTRIC RANGE 2b. MODELS REQUIRING POWER SUPPLY CORD KIT. RISK OF FIRE OR ELECTRICAL SHOCK MAY OCCUR IF AN INCORRECT SIZE RANGE CORD KIT IS USED, THE INSTALLATION INSTRUCTIONS ARE NOT FOLLOWED OR STRAIN RELIEF BRACKET IS DISCARDED. This appliance may be connected by means of a power supply cord. Only a power supply cord kit rated at 125/250 volts minimum, and marked for use with ranges shall be used. See Fig. 10 for cord kit ampere rating information.
PAGE 4
INSTALLATION INSTRUCTIONS FOR FREESTANDING ELECTRIC RANGE or 4B. POWER CORD CONNECTIONS (3-Wire Connection Instructions . For existing installations ONLY Refer to Fig. 13). 1. 2. 3. Follow the manufacturer’s installation instructions supplied with the strain relief and install (Also see Figs. 9, 10 & 11). Insert the end connectors for Line 1, Line 2 and Neutral and tighten securely to the terminal block (See Fig. 13).
PAGE 5
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30" LA INSTALACION Y EL SERVICIO DEBEN SER EFECTUADOS POR UN INSTALADOR CALIFICADO. IMPORTANTE: CONSERVE ESTAS INSTRUCCIONES PARA USO DEL INSPECTOR LOCAL DE ELECTRICIDAD. LEA Y CONSERVE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA. Espacios Libres y Dimensiones 1. 2. 3. Provea espacios libres adecuados entre la estufa y las superficies combustibles adyacentes. Ubicación – Revise el lugar donde será instalada la estufa.
PAGE 6
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30" 1b. Taladre agujeros pilotos e instale el soporte - Taladre un agujero piloto de 1/8" donde se vayan a instalar los tornillos. Si el soporte va a ser instalado en la pared, taladre un agujero piloto en un ángulo descente de aproximadamente 20° (Ver Fig. 5). Si el soporte va a ser instalado en pisos de mampostería o de cerámica, taladre un agujero piloto de 3/16" y 1-3/4" de profundidad.
PAGE 7
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30" Consulte la Tabla del Tamaño de la Abertura de Conexión de la Estufa (Figs. 9 y 10) para la información sobre los amperes del juego de cordón. Los bornes en los extremos de los almabres deben ser de anillo cerrado u horquillas abiertas con extremos dirigidos hacia arriba. Sujetacable 2b.
PAGE 8
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30" o 4B. CONEXIONES DEL CORDON DE ALIMENTACION Instrucciones para conexión trifilar (para instalaciones existentes SOLAMENTE Consulte la Fig. 13). 1. Antes del cableado de la estufa, examine los dibujos de la ubicación sugerida para la fuente de alimentación en la Fig. 3. Si está conectando a un sistema eléctrico tetrafilar, (un circuito de derivación nuevo o casa rodante requieren conexión tetrafilar): 1.