Use and Care Guide

5
OPERATING INSTRUCTIONS
Sanitize Option
To sanitize your dishes and glassware, select
the SANITIZE option. When selected, the
indicator light will come on and remain on until
the end of cycle. The water temperature in the
fi nal rinse will be raised to 156
o
F (69
o
C). This
option is available in POWER PLUS, NORMAL
WASH and TOP RACK Cycles. Only these
sanitization cycles have been designed to meet
NSF requirements.
The cycle time will be extended until the proper
water temperature is reached. Washing
action will continue during the water heating
delay. For best results, the incoming water
temperature should be at least 120
o
F (49
o
C).
The sanitize criteria may not be satisfi ed if there
is an interruption of the cycle, power failure or if
the incoming water temperature is below 120
o
F
(49
o
C).
To turn off the SANITIZE option, press
SANITIZE a second time. The indicator light will
turn off.
Delay Start
The DELAY START option allows you to
automatically delay starting your dishwasher
1-24 hours.
To start the DELAY START option, press DELAY
START until the desired delay time shows in the
STATUS window. A light will come on indicating
the delay has been set and will remain on until
cycle starts. Press the START/CANCEL pad to
start the delay option. If the delay option is
interrupted, the START/CANCEL pad will have to
be pressed again to return to delay option.
To cancel the DELAY START option and to
begin the selected cycle before the delay
period is over, press and hold START/CANCEL
pad for 3 seconds.
Heat Dry/Air Dry
Use of the HEAT DRY option, especially in
combination with use of rinse agent, will
enhance drying. If AIR DRY is selected the
heater will be de-activated during the drying
phase of the selected wash cycle. This will
slightly lower the energy use but will increase
the likelihood that the dishware will not dry
completely.
Child Lock Controls
To prevent children from accidently changing
the dishwasher cycle or starting the
dishwasher, to lock the dishwasher controls
press and hold DELAY START for 3 seconds.
An indicator light on the lock graphic pad will
illuminate when the controls are locked and no
new selections can be made until the lock is
released. To unlock the controls, press DELAY
START again for 3 seconds, and the indicator
light will go out.
To Cancel a Cycle
You can cancel a cycle anytime during the
cycle. Press and hold the START/CANCEL pad
for 3 seconds. The light above the cycle and
option selected will go out, and the START/
CANCEL light will remain illuminated, the
dishwasher will start a 90 second drain. At the
end of the drain, select the next desired cycle.
Favorite Cycle
The FAVORITE CYCLE option allows you to
program your preferred cycle and options into
one button. Once Programmed, simply select
FAVORITE CYCLE and then select START/
CANCEL.
To Program the FAVORITE CYCLE:
1. Select your preferred cycle and options
2. Press FAVORITE CYCLE for 3 seconds.
The display will " ash for 2 seconds indicating
the FAVORITE CYCLE option has been
programmed. To change the FAVORITE
CYCLE option simply repeat steps one and
two above.
Sahara Dry
TM
When SAHARA DRY
TM
option is selected,
the dishwasher extends drying time by
approximately 20 minutes. The SAHARA DRY
TM
option can be used with all cycles except
CHINA CRYSTAL, ENERGY SAVER and RINSE
ONLY. For best drying performance, also apply
an increased wash temperature by selecting
HI-TEMP WASH or even better, the SANITIZE
option.
The energy required to use the SAHARA DRY
TM
option costs pennies per cycle. You may
choose not to select the SAHARA DRY
TM
option;
however you may have items in your dish load
that will not be completely dry at the end of
the cycle.