All about the Use & Care of your Range TA B L E O F C O N T E N T S Setting Oven Controls .......................................... 13 Important Safety Instructions .................................3 Self-Cleaning....................................................... 23 Features at a Glance..............................................6 Care & Cleaning (Cleaning Chart) ......................... 25 Before Setting Surface Controls ..............................7 Care & Cleaning ....................
WELCOME & CONGRATULATIONS Product Registration Register Your Product The PRODUCT REGISTRATION CARD should be filled in completely, signed and returned to Electrolux Home Products. Serial Plate Location Congratulations on your purchase of a new appliance! At Electrolux Home Products, we are very proud of our product and are completely committed to providing you with the best service possible. Your satisfaction is our number one priority.
IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using this appliance. Save these instructions for future reference. DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING This symbol will help alert you to situations that may cause serious bodily harm, death or property damage.
IMPORTANT SAFETY INSTRUCTIONS CAUTION Do not store items of interest to children in the cabinets above the appliance. Children climbing on the cooktop to reach items could be seriously injured. • Do not leave children alone. Children should not be left alone or unattended in the area where an appliance is in use. They should never be allowed to sit or stand on any part of the appliance.
IMPORTANT SAFETY INSTRUCTIONS due to the sudden change in temperature. Check the manufacturer’s recommendations for cooktop use. • Do Not Use Decorative Surface Burner Covers. If an element is accidentally turned on, the decorative cover will become hot and possibly melt. Burns will occur if the hot covers are touched. Damage may also be done to the cooktop.
FEATURES AT A GLANCE 2 3 4 1 5 6 YOUR BUILT-IN RANGE FEATURES: 1. 2. 3. 4. 5. 6. Electronic oven control with kitchen timer. Left front element control and electronic display. Left rear element control and electronic display. Right rear element control and electronic display. Right front element control and electronic display. Keep warm zone control. 7. 8. 9. 10. 11. 12. 13. 14. 15. Lower oven self-clean door latch. Lower and upper oven vent. Broil element. Self-cleaning oven interior.
BEFORE SETTING SURFACE CONTROLS COOKTOP DISPLAY WINDOWS The cooktop controls provide a digital display for each element located on the cooktop. Power levels and messages are easily monitored and adjusted using the corresponding control keypads in combination with the window displays. POWER FAILURE (PF) MESSAGE The PF message (Figure 9) will be displayed whenever there has been a power interruption to the appliance. The PF message will disappear by itself after a few seconds.
BEFORE SETTING SURFACE CONTROLS USING PROPER COOKWARE ABOUT THE RADIANT SURFACE ELEMENTS Cookware should have flat bottoms that make good contact with the entire surface heating element (Figure 1). Check for flatness by rotating a ruler across the bottom of the cookware (Figure 2). For efficient cooking, turn off the element several minutes before cooking is complete. This will allow residual heat to complete the cooking process.
SETTING SURFACE CONTROLS SINGLE RADIANT ELEMENT The cooktop provides single radiant element located as illustrated. Use the following instructions when operating these elements. The suggested power level settings shown in Fig. 1 are based on cooking with medium sized aluminum pans with lids. Be sure to make any further setting adjustments for best surface cooking results. Suggested element power level settings table Setting Type of cooking High (8.
SETTING SURFACE CONTROLS DUAL RADIANT ELEMENT The cooktop provides a dual radiant element located as illustrated. Use the following instructions when operating this element. Use the Size keypad (Fig. 1) to select which portions of the dual element are needed for heating. The dual element size may be changed anytime the element is ON. To Operate the Dual Radiant Elements: 1. Place correctly sized cookware on the dual radiant element. Fig. 1 Fig. 2 Fig. 3 2.
SETTING SURFACE CONTROLS KEEP WARM ZONE The cooktop provides a keep warm zone located as illustrated. Use the following instructions when operating this element. The purpose of the keep warm zone is to keep hot cooked foods at serving temperature. Use the keep warm feature to keep cooked foods hot such as: vegetables, gravies, casseroles, soups, stews, breads, pastries and oven-safe dinner plates. Always start with hot food. It is not recommended to heat cold food on the keep warm zone.
BEFORE SETTING OVEN CONTROLS ARRANGING OVEN RACKS ALWAYS ARRANGE OVEN RACKS WHEN THE OVEN IS COOL (PRIOR TO OPERATING THE OVEN). Always use oven mitts when using the oven. To remove an oven rack, pull the rack forward until it stops. Lift up front of rack and slide out. To replace an oven rack, fit the rack onto the guides on the oven walls. Tilt the front of the rack upward and slide the rack back into place.
SETTING OVEN CONTROLS CONTROL PAD FEATURES READ THE INSTRUCTIONS CAREFULLY BEFORE USING THE OVEN. For satisfactory use of your oven, become familiar with the various features and functions of the oven as described below. Detailed instructions for each feature and function follow later in this Use & Care Guide. 16 1 2 3 9 10 4 5 6 7 8 11 12 13 14 15 1. Upper oven pad—Use to activate the upper oven for cooking operation. 2. Lower oven pad—Use to activate the lower oven for cooking operation. 3.
SETTING OVEN CONTROLS MINIMUM AND MAXIMUM CONTROL PAD SETTINGS All of the features listed below have minimum and maximum time or temperature settings that may be entered into the control. An ENTRY acceptance beep will sound each time a control pad is touched (the acceptance beep on the Oven Lockout pad is delayed 3 seconds). An ENTRY ERROR tone (3 short beeps) will sound if the entry of the temperature or time is below the minimum or above the maximum settings for the feature.
SETTING OVEN CONTROLS SETTING THE CLOCK The SET CLOCK pad is used to set the clock. The clock may be set for 12 or 24 hour time of day operation. The clock has been preset at the factory for the 12 hour operation. When the range is first plugged in, or when the power supply to the range has been interrupted, the timer in the display will flash. To set the clock (example below for 1:30) 1. Press SET CLOCK. "CLO" will appear in the display. 2. Press 1 3 0 pads to set the time of day to 1:30.
SETTING OVEN CONTROLS SETTING LOCKOUT FEATURE 2. Press SELF CLEAN to switch between normal sound operation and silent operation mode. The display will show either "bEEP On" or "bEEP OFF". The pad controls the Lockout feature. The Lockout feature automatically locks the oven doors, the control panel and the cooktop. It does not disable the Minute Timer or the interior oven lights. To activate the Lockout feature Note: If "bEEP On" appears, the control will operate with normal sounds and beeps.
SETTING OVEN CONTROLS QUICK PREHEAT SETTING BAKE Use the quick preheat feature when using single rack baking to quickly heat the oven to bake temperatures. Use this feature only for standard baking. A reminder tone will sound indicating when to place the food in the oven. The BAKE pad controls normal baking. If a rapid preheating is preferred, refer to the QUICK PREHEAT feature for instructions. The oven can be programmed to bake at any temperature from 170°F to 550°F.
SETTING OVEN CONTROLS SETTING BAKE TIME SETTING DELAY START Bake Time allows the oven to be set to cook for a specific length of time and shut off automatically. The oven will shut off and will beep when the countdown is finished. This feature can be used with Bake and Pizza cooking modes. To program the oven to begin baking immediately and to shut off automatically (example: BAKE at 350°F for 30 minutes): 1. Be sure the clock is set for the correct time of day. 2.
SETTING OVEN CONTROLS SETTING BROIL This mode is best for meats, fish and poultry up to 1” thick. Broiling is a method of cooking tender cuts of meat by direct heat under the broil element of the oven. The high heat cooks quickly and gives a rich, brown outer appearance. The BROIL pad controls the Broil feature. An optional Searing Grill, Broiler Pan and Insert are available via the enclosed accessories brochure (Figure 2 & 3).
SETTING OVEN CONTROLS SETTING PIZZA SETTING KEEP WARM The PIZZA pad has been designed to give optimum cooking performance when cooking your favorite pizza. The Pizza pad let you choose a preset between a frozen pizza (425°F) and a fresh pizza (400°F). If needed, a different target temperature than the presets can be entered. Some fresh pizza request using a broil feature for a few minutes, but this is not part of the Pizza pad presets.
SETTING OVEN CONTROLS SETTING THE SABBATH FEATURE (for use on the Jewish Sabbath & Holidays) The BAKE TIME and DELAY START pads are used to set the Sabbath feature. The Sabbath feature may only be used with the BAKE pad. The oven temperature may be set higher or lower after setting the Sabbath feature (the oven temperature adjustment feature should be used only during Jewish Holidays), however the display will not visibly show or provide any audible tones indicating whether the change occurred correctly.
SETTING OVEN CONTROLS ADJUSTING OVEN TEMPERATURE The temperature in the oven has been pre-set at the factory. When first using the oven, be sure to follow recipe times and temperatures. If you think the oven is cooking too hot or too cool for the temperature you select, you can adjust the actual oven temperature to be more or less than what is displayed. Before adjusting, test a recipe by using a temperature setting that is higher or lower than the recommended temperature.
SELF-CLEANING SELF-CLEANING What to Expect during Cleaning A self-cleaning oven cleans itself with high temperatures (well above normal cooking temperatures) which eliminate soils completely or reduces them to a fine powdered ash you can wipe away with a damp cloth. While the oven is in operation, the oven heats to temperatures much higher than those used in normal cooking. Sounds of metal expansion and contraction are normal. Odor is also normal as the food soil is being removed.
SELF-CLEANING SETTING SELF-CLEAN CYCLE TIME LENGTH The SELF CLEAN pad controls the Self-Cleaning feature. If you are planning to use the oven directly after a selfclean cycle remember to allow time for the oven to cool down and the oven door to unlock. This normally takes about one hour. So a 3 hour self-clean cycle will actually take about 4 hours to complete.
CARE & CLEANING (Cleaning Chart) CLEANING VARIOUS PARTS OF YOUR APPLIANCE Before cleaning any part of the appliance, be sure all controls are turned off and the appliance is COOL. REMOVE SPILLOVERS AND HEAVY SOILING AS SOON AS POSSIBLE. REGULAR CLEANING WILL REDUCE THE NUMBER OF MAJOR CLEANING LATER. Surfaces How to Clean Aluminum (trim pieces) & Vinyl Use hot, soapy water and a cloth. Dry with a clean cloth.
CARE & CLEANING CERAMIC GLASS COOKTOP CLEANING & MAINTENANCE Consistent and proper cleaning is essential to maintaining your Ceramic glass cooktop. Prior to using your cooktop for the first time, apply the recommended CERAMA BRYTE® Cleaning Creme to the ceramic surface. Clean and buff with a non abrasive cloth or pad. This will make cleaning easier when soiled from cooking. The special cooktop cleaning cream leaves a protective finish on the glass to help prevent scratches and abrasions.
CARE & CLEANING CLEANING RECOMMENDATIONS FOR THE CERAMIC GLASS COOKTOP (CONTINUED) Plastic or foods with a high sugar content: These types of soils need be removed immediately if spilled or melted onto the ceramic cooktop surface. Permanent damage (such as pitting of the cooktop surface) may occur if not removed immediately. After turning the surface elements OFF, use a razor blade scraper or a metal spatula with a mitt and scrape the soil from the hot surface (as illustrated).
CARE & CLEANING REMOVING AND REPLACING THE LIFTOFF OVEN DOOR 3. Firmly grasp both sides of oven door along the door sides (Do not use the oven door handle - See Figure 3). CAUTION The door is heavy. For safe, temporary storage, lay the door flat with the inside of the door facing down. Most oven doors contain glass that can break. Read the following recommendations: 1. Do not close the oven door until all the oven racks are fully in place. 2. Do not hit the glass with pots, pans, or any other object. 3.
BEFORE YOU CALL (Solutions to Common Problems) OVEN BAKING For best cooking results, heat the oven before baking cookies, breads, cakes, pies or pastries, etc. There is no need to preheat the oven for roasting meat or baking casseroles. The cooking times and temperatures needed to bake a product may vary slightly from your previously owned appliance. Baking Problems and Solutions Chart Baking Problems Causes Corrections Cookies and biscuits burn on the bottom.
BEFORE YOU CALL (Solutions to Common Problems) IMPORTANT Before you call for service, review this list. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance. OCCURRENCE POSSIBLE CAUSE/SOLUTION Range is not level. Poor installation. Place oven rack in center of oven. Place a level on the oven rack. Adjust leveling legs at base of range until the rack is level.
BEFORE YOU CALL (Solutions to Common Problems) OCCURRENCE POSSIBLE CAUSE/SOLUTION Scratches or abrasions on cooktop surface. Coarse particles such as salt or sand between cooktop and utensils can cause scratches. Be sure cooktop surface and bottoms of utensils are clean before usage. Small scratches do not affect cooking and will become less visible with time. Cleaning materials not recommended for ceramic-glass cooktop have been used.
MAJOR APPLIANCE WARRANTY Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions. Exclusions This warranty does not cover the following: 1.