Installation guide

Attach foam adhesive seal:
Attach foam adhesive seal along the bottom ofthe curtain bottom channel (FIG.8).
__ FIG._
,////"i .
A. Curtain housing
B. Foam adhesive seal
FIG .9 Angle of cabinet
bracket securely seated
on edge of inner sill.
binet
window i F_ Bracket
inner sill I I
window i
outer sill
Install Cabinet into Window:
1. Center empty cabinet in window:
FIG.10
I Ill A
B
1
A. Window sash
B. Empty cabinet
C. Window channel
Check that lower rail of air conditioner cabinet is behind and against back side of window sill. Maintain a firm hold on
the air conditioner cabinet (FIG.9). Lower window sash to hold the cabinet in place. Measure the distance between the
right side of the cabinet and the inside of the window channel (FIG. 10). Repeat for the left side. Adjust the cabinet until
the distance on each side is the same.
2. Attach the cabinet to window:
A: For wooden window:
Use a 3/16" drill bit to drill three starter holes 3/8" deep through the three holes in the cabinet and into the window sill,
and drill one starter hole 3/8" deep through the hole in the middle of top rail and into the window frame (FIG. 11). Attach
cabinet to window with three #10 x 1/2" pan-head Phillips screws and one #10 X 1/2" round-head screw (FIG.11).
B: For Vinyl-Clad window:
Use a 1/8" drill bit to drill one hole through the hole in the middle of top rail and into the window frame. Attach cabinet
to window with one #10 x 1/2" round-head Phillips screw (FIG.11). Place two safety locks into the holes that located
in the bottom of the cabinet and drive two locking screws through the safety locks into the cabinet as shown (FIG.12)
3. Check that air conditioner is tilted back about 1 1/8" to 1 1/2" (tilted about 3° to 4° downward to the outside, see
FIG.13). After proper installation, condensate should not drain from the overflow drain hole during normal use, correct
the slope otherwise. FIG. 13
iii:ii_iiiill
Window Sash
about I 1/8"-I 1/2"/
!,
Side Louvers
A. #10 X 1/2" pan-head Phillips screws A. #10 X 1/4" pan-head Phillips screws
B. #10 X 1/2" round-head screw B. Safety Lock
C. Window channel Only for Vinly-Clad Window
Attach Side Curtains to Window Frame:
1. Extend the side curtains out against the window frame h A FIG.14A ....A FIG.14B
(FIG.11) ...... I
2. Drill holes and drive locking screws: ]l I
A: For wooden windows:
Use a 3/32" drill bit to drill 4 starter holes through the holes in
the side curtains into the window. Drive four #10 X1/2" locking _j _ B
screws through the holes in the side curtains into the window ...........
sill and window frame(FIG.14A, FIG.14B). C
B: For Vinyl-Clad windows:
Use a 1/8" drill bit to drill two holes through the holes in the A. Window channel
side curtains into the window frame as shown (FiG.14A). B. left-hand curtain
Drive two #10 X 1/2" locking screws through the holes in the C. #10 X 1/2" round-head
side curtains into the window sash (FIG. 14A) screw bottom of the curtain
3. Trim the weather seal (6"X3/4"X1/12")with a proper length, peel off the protective backing and plug any gaps if
needed as shown (FIG.14B).
a
A. #10 X 1/2" round-head
screw
B. Slotted hole in the