Installation guide

ManualsBrandsFrigidaire ManualsRoom air conditionerOfficial Frigidaire room air conditioner

READ BEFORE INSTALLING UNIT

Compact Window Mounting (10,000-12,000 BTU)

The unit isfor window mounting only.

Carefully read the installation manual before beginning.

Follow each step as shown.

Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.

Pay attention to danger and safety notices.

To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may

be exposed:

Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install

the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins offront and rear coils. To

prevent injury or strain, use proper lifting and carrying techniques when moving unit.

Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended

period of time.

Handle air conditioner with care.

Make sure air conditioner does not fall during installation.

SAVE CARTON and these INSTALLATION

INSTRUCTIONS for future reference. The carton is

the best way to store unit during winter, or when not

in use.

• DO NOT USE ANY SCREWS OTHER THAN

THOSE SPECIFIED HERE.

• WHERE APPLICABLE, THE TOP RAIL MUST BE

SECURELY FASTENED WITH ALL FOUR (4)

SCREWS FOR SAFETY REASONS.

The top rail on your unit may already be installed. If not,

follow the steps below.

Top Rail Hardware Qty.

3/8" Screw

Top Rail

Mounting Hardware Qty.

1/2" screws 7 /

_ #:% lock frame 2 |

'%,_. : _ (For Wooden windows) /

" I '" lock frame I 2 /

kr) ::::-_ (For VinyFClad windows) /

_!_ % sash lock

_%_.............. LL_ weather seals 5 /

_ _ _ ...... (6"X 3/ 4"X l112") I

',_ _: window sash seal foam 1 |

TOOLS NEEDED

_, Philips Screwdriver

Drill (If pilot holes are needed)

Before installing, the top rail must be assembled on the unit.

A. Remove the air conditioner from the carton and place on a flat surface.

B. Remove top rail from the rear of the packaging material as shown in Fig. A

C. Align the hole in the top rail with those on the top of the unit as shown in Fig. B

D. Secure the top rail to the unit with the 3/8" Screws as shown in Fig. C

Top Rail

Packaging

2020215A1036

Summary of content (4 pages)

PAGE 1
READ BEFORE INSTALLING UNIT Compact Window Mounting (10,000-12,000 BTU) The unit is for window mounting only. Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only. Pay attention to danger and safety notices.
PAGE 2
LEFT + RIGHT FILLER PANEL ASSEMBLY NOTE= Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear of (5/16"). This is necessary for proper condensed water utilization and drainage, if you are not using the Side Panels for any reason, this pitch to the rear must be maintained! Place unit on floor, a bench or a table. There is a Left and Right side Filler Panels - be sure to use the proper panel for each side.
PAGE 3
Keep afirmgrip ontheairconditioner, carefully place theunit into thewindow opening sothebottom oftheair conditioner frame isagainst thewindow sill(FIG. 6A&FIG. 6B). Carefully close thewindow behind thetoprail oftheunit. INSI INSIDE I Wooden Windows Vinyl-Clad Windows Extend theside panels outagainst thewindow frame (FIG. 7Aforwooden windows), (FIG. 7BforVinyl*Clad windows). FIG.7A FIG.7B window frame Place theframe lock between theframe extensions and thewindow sillasshown (FIG.
PAGE 4
To secure lower sash in place, attach right angle sash lock with 1/2" (12.7mm) screw as shown (FIG. 10). NOTE: It is difficult to lock the windows with the sash lock for Vinyl*Clad windows, so you can use lock by window itself. Cut foam window seal and insert it into the space between the upper and lower sashes (FIG. 11). FIG. 10 FIG. 11 SEAL Check that air conditioner is tilted back about 1/4" to 1/2" (tilted about 2 ° to 4 ° downward to the outside, see FIG. 12A& FIG. 12B).