Installation Instructions

ManualsBrandsFranke ManualsDual-Mount Kitchen SinksDual Mount 20" Stainless Steel 3-Hole Single Bowl Utility Sink

EZT-SSDUAL-INST

Congratulations!

You have purchased a quality product designed for long lasting beauty. The following instructions will take

you step-by-step through the installation process and care of your product. We recommend reading the entire

instruction booklet before beginning.

Caution:

Risk of personal injury. Metal surfaces are sharp and can cause severe cuts. Use gloves

and handle sink and tools with care.

Installing Your New Sink

Tools And Materials

Installation Instructions:

Stainless Steel Sinks

Step 1: Remove existing sink

1. Leave the faucet and drain outlet in place

2. Shut off water supply valves (usually under sink).

3. Release any water that may be in the supply lines by opening faucet valves

(the same way you would normally turn your water on). Let water run until it

4. Disconnect the supply lines from the water supply valves.

6. Remove clips around underside of old sink.

1. Drivers

3. Silicone Sealant or Plumber’s Putty

2. 2” Hole Saw (if installing new countertop)

4. Adjustable

Wrench

9. Measuring

Tape

6. Drill

7. Jigsaw

5. Pipe Wrench (if steel pipe is used)

8. Gloves

10. Work Light

11. File

Supply valves

Waste trap

Supply

line

Step 1

#2 Robertson’s Bit

1/4” Nut Driver

Flat Head

Screwdriver

Summary of content (8 pages)

PAGE 1
Installation Instructions: Stainless Steel Sinks Congratulations! You have purchased a quality product designed for long lasting beauty. The following instructions will take you step-by-step through the installation process and care of your product. We recommend reading the entire instruction booklet before beginning. of personal injury. Metal surfaces are sharp and can cause severe cuts. Use gloves Caution: Risk and handle sink and tools with care. Installing Your New Sink Tools And Materials 4.
PAGE 2
Step 2 2. th Length Wid Step 2: OPTION A: Prepare existing countertop 1. Make sure existing countertop cut-out opening is the proper size. Set the new sink into opening. The sink rim should rest evenly on the countertop. Slight sawing. 3. OPTION B: Prepare a new countertop using the sink as a template 1. Carefully place the sink upside down on the countertop at the desired position. Trace the outline of the sink onto the countertop. Do not cut along this line. 2. Draw a line 1/2” (12.
PAGE 3
5. Do not overtighten. It is only necessary to draw the rim down snugly to the countertop. 6. Wipe excess sealant from perimeter with a wet cloth. Step 6: Final Steps 1. Connect and tighten hot and cold faucet supply lines, strainer, drain and trap assembly. Note: Depending on the the new sink installation. 2. Turn on water supply and examine all connections for leaks. If leak appears, tighten joint slightly. Do not overtighten. 3. 4.
PAGE 4
Step 6: Final Steps 1. Connect and tighten hot and cold faucet supply lines, strainer, drain and trap assembly. Note: Depending on the location of sink drain holes, it may be necessary to adjust the drain pipe fittings under the sink to accommodate the new sink installation. 2. Turn on water supply and examine all connections for leaks. If leak appears, tighten joint slightly. Do not overtighten. 3. With stopper in place, fill sink and examine area under sink and around drain flange for leaks. 4.
PAGE 5
Instrucciones de instalación: Fregaderos de acero inoxidable ¡Felicitaciones! Ha comprado un producto de calidad diseñado para brindar belleza duradera y muy fácil de instalar. Las instrucciones queaparecen a continuación le van a guiar paso a paso por el proceso de instalación y cuidado de su producto. Le sugerimos que lea todo el manual de instrucciones antes de seguir adelante. Precaución: Riesgo de lesiones personales. Las superﬁcies de metal tienen bordes aﬁlados y pueden causar cortes graves.
PAGE 6
Paso 2 1. Anc ho Largo inconvenientes sobre la encimera. Para realizar ajustes leves, puede utilizar una lima o sierra de vaivén. 2. Utilice la lima o la sierra de vaivén con cuidado para no fragmentar ni quebrar la encimera. 3. fregadero de plantilla 1. Con cuidado, coloque el fregadero al revés sobre la encimera en la ubicación que desee. Marque el contorno del fregadero en la encimera. No realice el corte siguiendo esta línea. 2. Dibuje una línea 1/2” (12,7 mm) dentro del contorno del fregadero.
PAGE 7
4. Debajo de la encimera, comience a apretar de manera uniforme los clips (asegurándose de que el fregadero permanezca en el centro del cutout) con un destornillador manual o eléctrico, alternando entre un lado y otro conforme aprieta hasta que todo el borde esté sellado. 5. No ajuste excesivamente. Basta con asentar el reborde firmemente sobre la encimera. 6. Limpie el exceso de sellador en el perímetro con un paño húmedo. 1. drenaje debajo del fregadero para que se adapten al fregadero nuevo. 2.
PAGE 8
Paso 6: Pasos finales 1. Conecte y ajuste los conductos de suministro de agua PASO 6 fría y caliente del grifo, el filtro, el drenaje y el ensamble del bote sifónico. Nota: Según la ubicación de los Base del grifo orificios de drenaje del fregadero, quizás sea necesario Brida superior del drenaje ajustar las conexiones de la tubería de drenaje debajo Fregaderos de del fregadero para que se adapten al fregadero nuevo. colocación Encimera sobrepuesta 2.