Table of Contents Introduction Instrument Cluster 4 12 Warning lights and chimes Gauges 12 19 Entertainment Systems 22 How to get going AM/FM stereo AM/FM stereo with CD AM/FM stereo with in-dash six CD Auxiliary input jack Satellite radio information Climate Controls Heater only Manual heating and air conditioning Automatic temperature control Rear window defroster Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power
Table of Contents Locks and Security 101 Keys Locks Anti-theft system 101 101 112 Seating and Safety Restraints Seating Safety restraints Airbags Child restraints Tires, Wheels and Loading Tire information Tire inflation Tire Pressure Monitoring System (TPMS) Vehicle loading Trailer towing Recreational towing Driving 115 115 121 140 149 167 169 171 184 188 194 206 208 Starting Brakes Traction Control™ Transmission operation 208 212 215 217 Roadside Emergencies 241 Getting roadside assistance H
Table of Contents Customer Assistance Reporting safety defects (U.S. only) 266 272 Cleaning 273 Maintenance and Specifications 283 Engine compartment Engine oil Battery Engine coolant Fuel information Air filter(s) Part numbers Maintenance product specifications and capacities Engine data 285 289 293 295 301 320 322 324 328 Accessories 332 Index 334 All rights reserved.
Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. Warning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.
Introduction BREAKING-IN YOUR VEHICLE Your vehicle does not need an extensive break-in. Try not to drive continuously at the same speed for the first 1,000 miles (1,600 km) of new vehicle operation. Vary your speed frequently in order to give the moving parts a chance to break in. Drive your new vehicle at least 500 miles (800 km) before towing a trailer. Additionally, during the first 500 miles (800 km) that you tow a trailer, do not drive over 70 mph (112 km/h) and do not make starts at full throttle.
Introduction Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury. Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passenger airbag.
Introduction To access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent, unless pursuant to court order or where required by law enforcement, other government authorities or other third parties acting with lawful authority. Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada.
Introduction Notice to owners of the 2007 F150 Note: Your vehicle is equipped with high performance tires. When first driving the vehicle after it has been parked for a period of time, you may experience a temporary ride disturbance. This is a characteristic of the tires and should be no reason for concern. The condition should correct itself within 5-15 miles (8-25 km) of driving. If the disturbance persists, have the tires serviced by an authorized dealer.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Windows Front/Rear Power Window Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack Check Fuel Cap Low Tire Pressure Warning MAX
Instrument Cluster WARNING LIGHTS AND CHIMES Base instrument cluster Base with Tachometer instrument cluster 12 2007 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)
Instrument Cluster Family Carrier instrument cluster Mid instrument cluster 13 2007 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus)
Instrument Cluster Luxury instrument cluster Harley-Davidson instrument cluster Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, refer to the respective system warning light for additional information.
Instrument Cluster Service engine soon: The Service engine soon indicator light illuminates when the ignition is first turned to the ON position to check the bulb and to indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing. Normally, the ⬙Service engine soon⬙ light will stay on until the engine is cranked, then turn itself off if no malfunctions are present.
Instrument Cluster Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON position when the engine is not running, or in a position between ON and START, or by applying the parking brake when the ignition is turned to the ON position.
Instrument Cluster Safety belt: Reminds you to fasten your safety belt. A BeltMinder威 chime will also sound to remind you to fasten your safety belt. Refer to the Seating and safety restraints chapter to activate/deactivate the BeltMinder威 chime feature. Charging system: Illuminates when the battery is not charging properly. Door ajar: Illuminates when the ignition is in the ON position and any door is open. Low tire pressure warning (if equipped): Illuminates when your tire pressure is low.
Instrument Cluster Four wheel drive low (if equipped): Illuminates when four-wheel drive low is engaged. 4x4 LOW Four wheel drive high (if equipped): Illuminates when four-wheel drive high is engaged. 4x4 HI Speed control: Illuminates when the speed control is activated. Turns off when the speed control system is deactivated. Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster, check for a burned out bulb.
Instrument Cluster Check gauge: Displays when any of the following conditions has occurred: • The engine coolant temperature is high. • The engine oil pressure is low. • The fuel gauge is at or near empty. Trans Fault: Displays when a transmission problem has been detected and shifting may be restricted. If the light remains on, have the system serviced immediately by your authorized dealer.
Instrument Cluster Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. Never remove the coolant reservoir cap while the engine is running or hot.
Instrument Cluster • With Full Message Center Press and release the message center INFO button until TRIP mode appears in the display. Press the RESET button to reset. Tachometer (if equipped): Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Battery voltage gauge: Indicates the battery voltage when the ignition is in the ON position.
Entertainment Systems AUDIO SYSTEMS Quick start — How to get going Listening to the radio 1. If the audio system is off, press VOL-PUSH to turn the radio on. Turn VOL-PUSH to adjust the volume. Note: The system may take a few moments to turn on. 2. Press AM/FM repeatedly to choose between AM/FM1/FM2 frequency bands. 3. Press / to manually go up/down the frequency band. SEEK to search Press down/up the chosen frequency band for the next strongest station. / . To disengage SEEK mode, press 4.
Entertainment Systems 2. Press AUX repeatedly to cycle through auxiliary audio sources. Select SAT1, SAT2 or SAT3 to listen to satellite radio. SEEK, SEEK to 3. Press access the previous or next satellite channel. You may also seek by music category. For further information, refer to CATEGORY listing under the MENU control on your specific audio system. 4. Once you are tuned to the desired channel, press and hold a memory preset (1–6) to save the channel.
Entertainment Systems For an in-dash six CD system, if a disc is not already loaded, press LOAD. Select a slot number using memory presets 1–6. When the display reads LOAD CD#, load the desired disc, label side up. If you do not choose a slot within 5 seconds, the system will choose for you. Once loaded, the first track will begin to play. To auto load up to 6 discs, press and hold LOAD until the display reads AUTOLOAD#. Load the desired disc, label side up.
Entertainment Systems Press SHUFFLE to engage shuffle mode. SHUFFLE ON will appear in the display. If you wish to engage shuffle mode right away, press SEEK to begin random play. Otherwise, random play will begin when the current track is finished playing. CD SHUF will appear in the display. To disengage, press SHUFFLE again. SHUFFLE OFF will appear in the display. Note: In track mode, all tracks on the current disc will shuffle in random order.
Entertainment Systems AM/FM stereo system (if equipped) Accessory delay: Your vehicle is equipped with accessory delay which allows you to operate the window switches and the audio for up to ten minutes after the ignition has been turned off or until either front door is opened. / : Press / to 1. manually go up or down the radio frequency. Press and hold for a fast advance through radio frequencies. Also use in AUDIO mode to gain access to various settings. 2.
Entertainment Systems FAD (Fade): Press AUDIO to reach the fade feature. Use / / SEEK to adjust the audio between the front (F) and back (B) speakers. TREB (Treble): Press to adjust the treble setting. Use SEEK to adjust. BASS (Bass): Press to adjust the bass setting. Use SEEK to adjust. / / / / SEEK to 3. SEEK: Press access the previous/next strong station. 4. Memory presets: To set a station: Select frequency band AM/FM1/FM2; tune to a station, press and hold a preset button until sound returns.
Entertainment Systems AM/FM stereo single CD/satellite compatible sound system (if equipped) Accessory delay: Your vehicle is equipped with accessory delay which allows you to operate the window switches and the audio for up to ten minutes after the ignition has been turned off or until either front door is opened. / : Press / to 1. manually go up or down the radio frequency. Press and hold for a fast advance through radio frequencies.
Entertainment Systems 3. MENU: Press MENU repeatedly to access to the following settings: CATEGORY (satellite radio if equipped): : Press MENU until the currently active category appears in the display (CATEGORY MODE). In / to scroll through the list of available CATEGORY MODE, press SEEK, SIRIUS channel Categories (Pop, Rock, News, etc.) Press or SCAN to select the category. After a category is selected, SEEK press SEEK to search for that specific category of channels only (i.e. ROCK).
Entertainment Systems FADE: Press MENU to reach the fade setting. Use SEEK, SEEK front (F) speakers. / / to adjust the audio between the back (B) and SPEEDVOL (Speed sensitive volume, if equipped): Press MENU to reach the SPEEDVOL setting. Radio volume automatically gets louder with increasing vehicle speed to compensate for road and wind noise. Use / / SEEK, SEEK to adjust. The default setting is off; increasing your vehicle speed will not change the volume level.
Entertainment Systems 5. SEEK: In radio mode, press / to access the previous/next strong station. / In CD/MP3 mode, press to access the previous/next CD/MP3 track. SEEK, SEEK to In satellite radio mode (if equipped), press seek to the previous/next channel. If a specific category is selected, SEEK, SEEK to seek to the (Jazz, Rock, News, etc.), press previous/next channel in the selected category. Press and hold SEEK, SEEK to fast seek through the previous /next channels.
Entertainment Systems 9. FOLDER: In folder mode, FOLDER to access the press previous folder on MP3 discs, if available. 10. FF (Fast forward): Press FF to manually advance in a CD/MP3 track. 11. REW (Rewind): Press REW to manually reverse in a CD/MP3 track. 12. Memory presets: To set a station: Select frequency band AM/FM1/FM2; tune to a station, press and hold a preset control until sound returns. You may store up to six stations in each frequency band for a total of 18.
Entertainment Systems Satellite radio is available only with a valid SIRIUS radio subscription. Check with your authorized dealer for availability. 14. AM/FM: Press AM/FM to select AM/FM1/FM2 frequency band. 15. ON/OFF/Volume: Press VOL-PUSH to turn ON/OFF. Turn VOL-PUSH to increase/decrease volume. Note:If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. 16.
Entertainment Systems Premium/Audiophile in-dash six CD/MP3/satellite compatible sound system (if equipped) Accessory delay: Your vehicle is equipped with accessory delay which allows you to operate the window switches and audio for up to ten minutes after the ignition has turned off or until either front door has opened. / (Tune/Disc selector): 1. In radio mode, press to manually ) or down ( ) the go up ( radio frequency. Press and hold for a fast advance through radio frequencies.
Entertainment Systems 3. MENU: Press repeatedly to access to the following settings: CATEGORY (satellite radio if equipped): Press MENU until the currently active category appears in the display (CATEGORY MODE). In CATEGORY MODE, press / to scroll through the list of available SIRIUS channel Categories (Pop, Rock, News, etc.) Press SEEK or SCAN to select the category. After a category is selected, press SEEK to search for that specific category of channels only (i.e. ROCK).
Entertainment Systems BASS: Press MENU to reach the bass setting. Use SEEK, SEEK to adjust. / / TREB (Treble): Press MENU to reach the treble setting. / / SEEK, SEEK to adjust. Use BAL (Balance): Press MENU to reach the balance setting. / / SEEK, SEEK to adjust the audio between the left Use (L) and right (R) speakers. / / FADE: Press MENU to reach the fade setting. Use SEEK, SEEK to adjust the audio between the back (B) and front (F) speakers.
Entertainment Systems COMPRESS (Compression): Available only in CD/MP3 mode. Press / / MENU until COMPRESS ON/OFF appears in the display. Use SEEK, SEEK to toggle ON/OFF. When COMPRESS is ON, the system will bring soft and loud CD passages together for a more consistent listening level. 4. AUX: Press repeatedly to cycle through FES/DVD (if equipped), LINE IN (Auxiliary audio mode, if equipped), SAT1, SAT2 and SAT3 modes (Satellite Radio, if equipped).
Entertainment Systems 7. SHUFFLE: In CD/MP3 mode, press SHUFFLE to engage shuffle mode. SHUFFLE ON will appear in the display. If you wish to engage shuffle mode right away, press SEEK to begin random play. Otherwise, random play will begin when the current track is finished playing. CD SHUF will appear in the display. To disengage, press SHUFFLE again. SHUFFLE OFF will appear in the display. Note: In track mode, all tracks on the current disc will shuffle in random order.
Entertainment Systems In CD/MP3 mode, press and release to display track title, artist name, and disc title and file name (if available). In satellite radio mode (if equipped), press and release to enter TEXT MODE and display the current song title. While in TEXT MODE, press again to scroll through the current song title, artist, channel category and the SIRIUS long channel name. In TEXT MODE, sometimes the display requires additional text to be to view the displayed.
Entertainment Systems To auto load up to 6 discs, press and hold LOAD until the display reads AUTOLOAD#. Load the desired disc, label side up. The system will prompt you to load discs for the remaining available slots. Insert the discs, one at a time, label side up, when prompted. Once loaded, the disc in preset #1 will begin to play. Note: An MP3 disc with folders will show F001 (folder #) T001 (track #) in the display. An MP3 disc without folders will show T001 (track#) in the display.
Entertainment Systems Auxiliary input jack (if equipped) Your vehicle may be equipped with an Auxiliary Input Jack (AIJ), located in the instrument panel tray. The Auxiliary Input Jack provides a way to connect your portable music player to the in-vehicle audio system. This allows the audio from a portable music player to be played through the vehicle speakers with high fidelity.
Entertainment Systems 4. Turn the radio on, using either a tuned FM station or a CD loaded into the system. Adjust the volume to a comfortable listening level. 5. Turn the portable music player on and adjust the volume to 1/2 the volume. 6. Press AUX on the vehicle radio repeatedly until LINE IN appears in the display. You should hear audio from your portable music player although it may be low. 7.
Entertainment Systems AM: 530, 540–1700, 1710 kHz FM: 87.7, 87.9–107.7, 107.9 MHz Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, the weaker the signal and the weaker the reception. • Terrain: Hills, mountains, tall buildings, power lines, electric fences, traffic lights and thunderstorms can interfere with your reception.
Entertainment Systems MP3 track and folder structure Your MP3 system recognizes MP3 individual tracks and folder structure as follows: • There are two different modes for MP3 disc playback: MP3 track mode (system default) and MP3 folder mode. For more information on track and folder mode, refer to Sample MP3 structure in the following section. • MP3 track mode ignores any folder structure on the MP3 disc. The player numbers each MP3 track on the disc (noted by the .mp3 file extension) from T001 to T255.
Entertainment Systems Satellite radio information (if equipped) Satellite radio channels: SIRIUS broadcasts a variety of music, news, sports, weather, traffic and entertainment satellite radio channels. For more information and a complete list of SIRIUS satellite radio channels, visit www.sirius.com in the United States, www.sirius-canada.ca in Canada, or call SIRIUS at 1–888–539–7474.
Entertainment Systems Satellite Radio Electronic Serial Number (ESN): This 12–digit Satellite Serial Number is needed to activate, modify or track your satellite radio account. You will need this number when communicating with SIRIUS. While in Satellite Radio mode, you can view this number on the radio display by pressing AUX and Preset 1 control simultaneously. Radio Display ACQUIRING SAT FAULT INVALID CHNL UNSUBSCRIBED NO TEXT Condition Action Required Radio requires more No action required.
Entertainment Systems Radio Display NO TEXT NO TEXT NO SIGNAL UPDATING CALL SIRIUS 1–888–539–7474 Condition Song title information not available. Action Required Song title information not available at this time on this channel. The system is working properly. Category information Category information not available. not available at this time on this channel. The system is working properly.
Climate Controls HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. : Distributes outside air through the instrument panel vents. : Distributes outside air through the instrument panel vents and the floor vents.
Climate Controls 3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel. Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop. MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Temperature selection: Controls the temperature of the airflow in the vehicle.
Climate Controls 3. A. R Rear defroster (if equipped): Press to defrost the rear window. Refer to Rear window defroster (if equipped) later in this chapter for more information. 3. B. Heated mirrors (if equipped): Press to activate/deactivate. This function will clear snow, fog and thin ice from the side rear view mirrors. 4. Recirculation control : Press to activate/deactivate air recirculation in cabin.
Climate Controls • Move the temperature control to the coolest setting. • Select A/C and recirculated air ( to provide colder airflow. ). Use recirculated air with A/C • Set the fan to the highest speed initially, then adjust to maintain comfort. • To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows.
Climate Controls Temperature conversion: To switch between Fahrenheit and Celsius: If your vehicle is equipped with a full message center, refer to Setup menu in the Message center section of the Driver Controls chapter for more information. If your vehicle is equipped with a mini message center, see your authorized dealer for temperature conversion. , A/C, MAX A/C: For maximum cooling performance, press and set the temperature to 60°F and the highest blower setting.
Climate Controls 4. Recirculation control: Press to activate/deactivate air recirculation in cabin. Recirculated air may reduce the amount of time to cool down the interior of the vehicle and may also help reduce undesired odors from reaching the interior of the vehicle. Recirculation can be (defrost). engaged manually in any other airflow selection except Recirculation may turn off automatically. 5. A/C control: Press to activate/deactivate air conditioning.
Climate Controls Automatic Temperature Control (ATC) system with heated seats (if equipped) Temperature conversion: To switch between Fahrenheit and Celsius: If your vehicle is equipped with a full message center, refer to Units (Fahrenheit/Celsius) in the Driver Controls chapter. If your vehicle is equipped with a mini message center, refer to Mini message center electronic compass temperature display in the Driver Controls Chapter.
Climate Controls MAX A/C: For maximum cooling performance, press , A/C, , and set the temperature to 60°F and the highest blower setting. 1. Defrost: Distributes outside air through the windshield defroster vents and demister vents. Can be used to clear the windshield of fog and thin ice. 2. Fan speed control: Press to manually increase or decrease the fan speed. To return to automatic fan operation, press AUTO. 3. A. R Rear defroster: Press to defrost the rear window.
Climate Controls 12. A/C control: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engages automatically in AUTO, (defrost) and (floor/defrost). 13. OFF: Outside air is shut out and the fan will not operate. 14. Temperature control: Press to increase/decrease the temperature in the vehicle cabin. 15. AUTO: To engage automatic temperature control, press AUTO and select the desired temperature using the temperature control.
Climate Controls Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop. REAR WINDOW DEFROSTER (IF EQUIPPED) R The rear defroster control is located on the climate control panel and works to defrost your rear window from fog and thin ice. If equipped, it also operates the heated mirror to remove snow and thin ice from the side mirrors. Ensure that the ignition is ON. Press to turn the defroster ON/OFF.
Lights HEADLAMP CONTROL Rotate the headlamp control to clockwise to the first position turn on the parking lamps. Rotate clockwise to the second to also turn on the position headlamps. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
Lights Foglamp control (if equipped) The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamp , or control is in the position and the high beams are not turned on. Pull headlamp control towards you to turn foglamps on. The foglamp will illuminate if indicator light the ignition is in the ON position. High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate.
Lights Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation.
Lights 3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood. Cover one of the headlamps so no light hits the wall. 4. On the wall or screen you will observe a light pattern with a distinct horizontal edge towards the right. If this edge is not at the horizontal reference line, the beam will need to be adjusted so the edge is at the same height as the horizontal reference line. 5.
Lights INTERIOR LAMPS Map lamps To turn on the map lamps, press the control next to each lamp. Rear map lamp (if equipped) The rear map lamp lights are located on the end of the overhead rail system. The lamps can be turned on or off by pushing on the lens. Rear dome lamp (if equipped) • ON or D : The dome light will stay on. • DOOR or middle position: The dome light will only come on if a door is opened. : The lamp will not • OFF or come on at all.
Lights Dome/courtesy lamps (if equipped) The dome lamp lights when: • any door is opened. • the instrument panel dimmer switch is rotated up until the courtesy lamps come on. • any of the remote entry controls are pressed and the ignition is OFF. The reading portion, the two outer lights, can only be toggled on and off at the lamp.
Lights Function Number of bulbs 2 2 2 2 2 2 2 Trade number Headlamps H13 / 9008 Front park/turn lamps 3157A (amber) Front sidemarker 194 Foglamps 9140 Backup lamp (except Harley) 3156 Backup lamp (Harley) 3155 Rear stop/turn/sidemarker/tail 4057K or 3057K lamp High-mount brakelamp 1 921 Cargo lamp 2 921 License plate lamp 2 194 Exterior mounted mirror turn 2 See your dealer signal indicator (if equipped) Puddle lamp (if equipped) 2 See your dealer All replacement bulbs are clear in color except where not
Lights 5. Remove the bulb by turning it counterclockwise, then pull it straight out. Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. Install the new bulb in reverse order. Replacing front parking lamp/turn signal/sidemarker bulbs 1. Make sure the headlamp control is in the OFF position and open the hood. 2.
Lights 4. Slide the headlamp assembly forward disconnecting the snap attachment at the fender. 5. Remove bulb socket from the lamp assembly by turning it counterclockwise and then pull the bulb straight out. Install the new bulb(s) in reverse order. Replacing tail/brake/turn signal/backup lamp bulbs 1. Make sure the headlamp control is in the OFF position. 2. Open the tailgate to expose the lamp assembly screws and remove the two screws from the tail lamp assembly. 3.
Lights Replacing high-mount brake and cargo lamp bulbs Make sure the headlamp control is in the OFF position. 1. Remove the two screws and move the lamp assembly away from the vehicle to expose the bulb sockets. 2. Remove the bulb socket by rotating counterclockwise and pulling it out of the lamp assembly. 3. Pull the bulb straight out of the socket and push in the new bulb. Install the new bulbs in reverse order. Replacing foglamp bulbs (if equipped) 1.
Driver Controls MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three times with washer fluid. • a long push and hold: the wipers and washer fluid will be activated for up to ten seconds.
Driver Controls While holding the steering column, pull the lever up to its original position to lock the steering column. Never adjust the steering column when the vehicle is moving. ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamps. CENTER CONSOLE (IF EQUIPPED) The center console offers several useful storage features. These include: 1. Cupholders 1 2 2. Tissue holder in lid 3. Power point 4.
Driver Controls OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package. The overhead console can come on rails, which can be removed by the customer, or it can come as a non-rail component of the headliner, which cannot be removed. If your vehicle is equipped with a overhead console rail system, there are several features that can be operated. 1. To open the bins, move the center latch forward which will allow the door to be opened. 2.
Driver Controls • When on the overhead rail, adjacent bins must be pinned together. Bins adjacent to the End Cap must be pinned to the End Cap. Bins without pin attachments should not be placed on the overhead rail. Failure to pin the bins together can allow the bins to become separated from the rail under certain conditions. Bin Removal Attach and remove bins from the rail using the following instructions: Place both palms on the underside of the storage bin, avoiding the storage bin door.
Driver Controls While pushing upwards with palms, grip the side latches with fingers and squeeze. With pressure applied with palms and side latches squeezed down, pull downward on the entire storage bin and remove. AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug.
Driver Controls The auxiliary power point is located on the instrument panel. Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W. To prevent the battery from being discharged, do not use the power point longer than necessary when the engine is not running. An additional auxiliary power point is located on the lower rear side of the center console.
Driver Controls Cupholder/Ashtray (if equipped) The cupholder/ashtray is located on the instrument panel. To open cupholder/ashtray, push in on the door and release. The door will spring out 1/4+ inches. Then pull cupholder/ashtray assembly out the remaining distance to utilize. To close, push assembly in completely and release. Ashtray (if equipped) The ashtray is located on the instrument panel. To open ashtray, push in on the door and release. The ashtray assembly will tip out.
Driver Controls Press and hold the bottom part of the rocker switch to open the window. Press and hold the top part of the rocker switch to close the window. One touch down Allows the driver’s window to open fully without holding the control down. Press completely down on the bottom part of the rocker switch and release quickly. Press the rocker switch again to stop. Window lock (if equipped) The window lock feature allows only the driver to operate the power windows.
Driver Controls • Press and hold the bottom part of the rocker switch to open window all the way to the full open position. • Press and hold the top part of the rocker switch to close the window. When operating the power sliding back window you must ensure all rear seat occupants and/or cargo are not in the proximity of the back window. Do not leave children unattended in the vehicle and do not let children play with the power sliding back window, they may seriously injure themselves.
Driver Controls EXTERIOR MIRRORS Power side view mirrors To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. Fold-away mirrors (if equipped) Fold the side mirrors in carefully before driving through a narrow space, like an automatic car wash.
Driver Controls Heated outside mirrors (if equipped) Heated mirrors remove ice, mist and fog. To activate the heated mirrors, press the rear defrost button R located on the climate control panel. Refer to Rear Window Defrost in the Climate Controls chapter for more information. On vehicles not equipped with rear defrost, press the heated mirror control located on the climate control panel, refer to the Climate Controls chapter for more information.
Driver Controls Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving. SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 30 mph (48 km/h) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 30 mph (48 km/h). Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.
Driver Controls Resuming a set speed Press the RES/RESUME control and release it. This will automatically return the vehicle to the previously set speed. The RES/RESUME control will not work if the vehicle speed is not faster than 30 mph (48 km/h). Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET control until you get to the desired speed, then release the control. You can also use the SET control to operate the Tap-Up function.
Driver Controls • Depress the brake pedal until the desired vehicle speed is reached, press the SET control. Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or the clutch pedal (if equipped). This will not erase your vehicle’s previously set speed, if RES/RESUME is then selected, the vehicle will return to the previously set speed. • Press the speed control OFF control. This will erase your vehicle’s previously set speed.
Driver Controls In Satellite Radio mode (if equipped): • Press and release SEEK to advance through preset channels or press and hold SEEK to increment to the next subscribed channel. In CD mode: • Press and release SEEK to select the next track selection on the CD or press and hold SEEK to fast forward in the current track selection. In any mode: • Press VOL + or − to adjust volume. Climate control features Press TEMP + or - to adjust temperature. Press FAN + or - to adjust fan speed.
Driver Controls When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the proximity of the moon roof opening. Note: The moon roof will open to the “comfort” position first before opening all the way. The “comfort” position helps to alleviate rumbling wind noise which may happen in the vehicle with the roof fully opened. To open the moon roof: The moon roof is equipped with a one-touch open feature. Press and release control.
Driver Controls When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and objects are out of the way to prevent potential harm or damage. Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982).
Driver Controls 3. Simultaneously press and hold both the HomeLink威 and hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator and Canadian Programming” in this section for Canadian residents. 4. The indicator light will flash slowly and then rapidly. Release both buttons when the indicator light flashes rapidly.
Driver Controls Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing Steps 1 and 2 outlined in the “Programming” section, replace Step 3 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating.
Driver Controls Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds. HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with Step 2 in the “Programming” section.
Driver Controls Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass calibration adjustment. Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps.
Driver Controls 1. Start the vehicle. 2. To enter the compass calibration mode, press and hold the button for greater than eight seconds. The display will then show CAL in the display window. 3. Drive the vehicle slowly (less than 3 mph [5 km/h]) in circles until CAL indicator turns off. As many as 5 complete circles may be required. 4. The compass is now calibrated.
Driver Controls • Average Fuel Economy • Trip Elapsed Drive Time Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter. Compass display The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy.
Driver Controls 6. Press the RESET, then press SETUP control repeatedly until the correct zone setting for your geographic location is displayed on the message center. The range of zone values are from 01 to 15 and “wraps” back to 01. 7. To exit the zone setting mode, and to “lock in” your change, press and release the RESET control. Perform compass calibration in an open area free from steel structures and high voltage lines.
Driver Controls DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is reinitialized to a factory default value if the battery is disconnected. Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/100 km.
Driver Controls Setup menu Press this control for the following displays: • System Check • Units (English/Metric) • Autolock • Autolamp Delay • Language System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for three seconds.
Driver Controls 1. To disable/enable the autolock feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the autolocks ON or OFF. Autolamp delay This feature keeps your headlights on for up to three minutes after the ignition is switched off. 1. To disable/enable the autolamp delay feature, select this function from the SETUP control for the current display mode. 2.
Driver Controls The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message. Warning messages that have been reset are divided into two categories: • They will reappear on the display ten minutes from the reset. • They will not reappear until an ignition OFF-ON cycle has been completed.
Driver Controls to Engine coolant in the Maintenance and Specifications chapter. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. Never remove the coolant reservoir cap while the engine is running or hot. REDUCED ENGINE POWER. Displayed when the engine is overheating. Stop the vehicle as soon as safely possible, turn off the engine. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. STOP ENGINE SAFELY.
Driver Controls LOW TIRE PRESSURE (if equipped). Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. TIRE PRESSURE MONITOR FAULT (if equipped). Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. TIRE PRESSURE SENSOR FAULT (if equipped).
Driver Controls Position the floor mat so that the eyelet is over the pointed end of the retention post. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure. TAILGATE LOCK (IF EQUIPPED) Your vehicle may be equipped with a tailgate lock designed to help prevent theft of the tailgate. • Insert ignition key and turn to the right to engage lock. • Turn ignition key to the left to unlock.
Driver Controls BED EXTENDER (IF EQUIPPED) Your vehicle may be equipped with a bed extender designed to extend the pickup box for larger loads. To extend the bed extender : 1. Lower tailgate. 2. Pull the lever on each side of the bed extender to release it from the pickup box. 3. Lift the bed extender over on to the tailgate. 4. Evenly push down on the bed extender and push the lever in on each side locking it in place. To stow the bed extender, follow steps one through four in reverse order.
Driver Controls To remove the bed extender: 1. Extend the bed extender. 2. Pull the lever on each side of the bed extender to unlock it. Make sure the locking clip screws are loose before removing the bed extender. 3. Press the locking clips below the middle bar and lift the bed extender out of the channels on the “D” pillar. To install the bed extender, follow the removal procedure in reverse order.
Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to the SecuriLock娂 passive anti-theft system section in this chapter for more information. POWER DOOR LOCKS (IF EQUIPPED) The power door lock controls are located on the driver and front passenger door panels. Press control to unlock all vehicle doors.
Locks and Security • the ignition is in the 3 (ON) position, • you shift into any gear putting the vehicle in motion, and • the brake pedal is released and the vehicle attains a speed greater than 5 mph (8 km/h). The autolock feature repeats when: • any door is opened then closed while the ignition is in the 3 (ON) position, and • the brake pedal is released and the vehicle attains a speed greater than 5 mph (8 km/h).
Locks and Security horn will chirp once if autolock was deactivated or twice (one short chirp and one long honk) if autolock was activated. 5. Turn the ignition to the 1 (OFF/LOCK) position to exit programming. Note: After exiting the driver configuration mode, the horn will chirp once to indicate a feature has been activated/deactivated. Keyless entry key pad procedure 1. Turn the ignition to the 1 (OFF/LOCK) position. 2. Close all the doors. 3. Enter 5–digit entry code 4. Press and hold the 7 • 8.
Locks and Security REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Locks and Security 2. Press and release again within three seconds to confirm that all the doors are closed and locked. Note: The doors will lock again, the horn will chirp once, and the parklamps will flash once more. If any of the doors are not properly closed the horn will make two quick chirps and the parklamps will not flash.
Locks and Security Note: The panic alarm will only operate when the ignition is in the 1 (OFF/LOCK) position. Memory feature (if equipped) The remote entry system can also control the memory feature. control once to unlock the driver’s door. Pressing Press the control will automatically move the seat and adjustable pedals to the the desired memory position (the memory position corresponds to the transmitter being used). Activating the memory feature To activate this feature: 1.
Locks and Security To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery.
Locks and Security Programming remote transmitters It is necessary to have all (maximum of six — original and/or new) of your remote transmitters available prior to beginning this procedure. If all remote entry transmitters are not present during the programming procedure, the transmitters that are not present during programming will no longer operate the vehicle. To program the transmitters yourself: Note: Ensure the brake pedal is not 3 depressed during this sequence.
Locks and Security • the remote transmitter lock control is pressed, or • after 25 seconds of illumination. The dome lamp control (if equipped) must not be set to the off position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 30 minutes after the last door is closed, even if the dimmer control is on.
Locks and Security 4. Within five seconds, press the control two times. Note: One horn chirp should be heard, indicating the system has been disabled. Conversely, a horn chirp followed by a honk will indicate the system is enabled. Pressing the power door control two times again will turn the feature ON if it was previously OFF, or OFF if it was previously ON.
Locks and Security • one minute of keypad inactivity. • the control is pressed on the remote entry transmitter. • the ignition is turned from the 1 (OFF/LOCK) position to the 3 (ON) position, or from the 3 (ON) position to the 1 (OFF/LOCK) position. Programming a personal entry code To create your own personal entry code: 1. Enter the factory set code (keypad will illuminate when pressed). 2. Within five seconds press the 1 • 2 on the keypad. 3. Enter your personal 5-digit code.
Locks and Security SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Your vehicle comes with two coded keys; additional coded keys may be purchased from your authorized dealer.
Locks and Security Automatic arming The vehicle is armed immediately after switching the ignition to the 1 (OFF/LOCK) position. 3 2 4 1 Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle. Replacement keys If your keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to an authorized dealer. The key codes need to be erased from your vehicle and new coded keys will need to be programmed.
Locks and Security 1. Insert the first previously 3 programmed coded key into the ignition and turn the ignition from 2 the 1 (OFF/LOCK) position to the 3 (ON) position (maintain ignition in 4 the 3 (ON) position for at least one second, but no more than ten seconds). 1 2. Turn ignition from the 3 (ON) position back to the 1 (OFF/LOCK) position in order to remove the first coded key from the ignition. 3.
Seating and Safety Restraints SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.
Seating and Safety Restraints Push control to lower head restraint. Front seat • Lift the track release bar to move the seat forward or rearward. Make sure that the seat is relatched into place. • Pull the release lever handle located on the side of the seat up to move the seatback forward or backward.
Seating and Safety Restraints Using the armrest (if equipped) Push the release control to move the armrest up or down. Using the manual lumbar support For more lumbar support, turn the lumbar support control toward the front of vehicle. For less lumbar support, turn the lumbar support control toward the rear of vehicle. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving.
Seating and Safety Restraints Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor. To reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in the seatback map pocket (if equipped) when a child is in the front passenger seat.
Seating and Safety Restraints Memory seats/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat and adjustable pedals to two programmable positions. The memory seat control is located on the driver’s seat. • To program position one, move the driver seat, and adjustable pedals to the desired position. Press the SET control. The SET control indicator light will briefly illuminate. While the light is illuminated, press control 1.
Seating and Safety Restraints The head restraints can be moved up and down. Lift the head restraint so that it is located directly or as close as possible behind your head. Push control to lower head restraint. Folding up the rear seats (if equipped ) The rear seat has a split 60/40 cushion. Each seat cushion can be flipped up into the seatback position. 1. Pull control to release seat cushion. 2. Rotate seat cushion up until it locks into vertical storage position.
Seating and Safety Restraints Returning the seat to seating position Before returning the seatback to its original position, make sure that cargo or any objects are not trapped underneath the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision. 1. Pull control on the side of the seat to release seat cushion from storage position. 2.
Seating and Safety Restraints classification and conditions. A collection of crash and occupant sensors provides information to the Restraints Control Module (RCM). During a crash, the RCM activates the safety belt pretensioners and/or either none, one, or both stages of the dual-stage airbag supplemental restraints based on crash severity and occupant classification and conditions.
Seating and Safety Restraints and they move forward during pre-crash braking. The most effective way to reduce the risk of unnecessary injuries is to make sure all occupants are properly restrained. Accident statistics suggest that children are much safer when properly restrained in the rear seating positions than in the front. Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag.
Seating and Safety Restraints Front outboard safety belt energy management retractors The front outboard safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant’s forward momentum. This helps reduce the risk of force-related injuries to the occupant’s chest by limiting the load on the occupant. Refer to Energy management retractors section in this chapter.
Seating and Safety Restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an airbag supplemental restraint system (SRS) is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
Seating and Safety Restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. To unfasten, push the release button and remove the tongue from the buckle.
Seating and Safety Restraints 2. Insert the belt into the clip on the back panel. Protect the stowed belt if you carry cargo this may damage or soil the belt. If the belt has been disconnected to carry large objects behind the seat, reconnect it as follows: 1. Remove the belt from the stowage clip on the back panel. 2. Buckle the small tongue on the end of the belt into the mini-buckle on the driver’s side. The belt is now ready for use.
Seating and Safety Restraints shortened, but pinches the webbing to keep the lap portion from getting longer. The cinch tongue is designed to slip during a crash, so always wear the shoulder belt properly and don’t allow any slack in either the lap or shoulder portions. Before you can reach and latch a combination lap and shoulder belt having a cinch tongue into the buckle, you may have to lengthen the lap belt portion of it. 1. To lengthen the lap belt, pull some webbing out of the shoulder belt retractor.
Seating and Safety Restraints Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.
Seating and Safety Restraints Shorten and fasten the belt when not in use. Energy management retractors Your vehicle has a safety belt system equipped with energy management retractors at the driver and front outboard passenger seating positions. An energy management retractor is a device which pays out webbing in a controlled manner. This feature is designed to help further reduce the risk of force-related injuries to the occupant.
Seating and Safety Restraints When to use the automatic locking mode • Anytime a child safety seat is installed in a front outboard passenger in a Regular Cab/ SuperCab/ SuperCrew or any rear seating position of a SuperCab or SuperCrew. The Regular Cab front center seatbelt has a cinch mechanism. Refer to Safety belt with locking cinch tongue (Regular Cab center only) earlier in this chapter. Children 12 years old and under should be properly restrained in a rear seat whenever possible.
Seating and Safety Restraints 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
Seating and Safety Restraints The driver and front outboard passenger safety belt pretensioners are designed to activate only during certain frontal or near-frontal collisions with sufficient longitudinal deceleration. A safety belt buckle pretensioner is a device which tightens the webbing of the lap and shoulder belts during some collisions in such a way that they fit more snugly against the body.
Seating and Safety Restraints Front safety belt height adjustment (if equipped) Your vehicle has safety belt height adjustments for the driver and right front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, push the button and slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place.
Seating and Safety Restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... Then... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.
Seating and Safety Restraints The BeltMinder威 feature uses two different warning chimes. During the first minute of activation, the warning chime will sound once every second. The remaining warning chimes will sound twice every second while the system is activated. If... The driver’s and front passenger’s safety belts are buckled...
Seating and Safety Restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider... “Crashes are rare 36700 crashes occur every day. The more we events” drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. “I’m not going far” 3 of 4 fatal crashes occur within 25 miles of home. “Belts are We design our safety belts to enhance comfort.
Seating and Safety Restraints Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the BeltMinder威 chime. To do so may adversely affect the performance of the vehicle’s air bag system. One time disable If at any time the driver/front passenger quickly buckles then unbuckles the BeltMinder威 feature for that seating position, the BeltMinder娂 is disabled for the current ignition cycle.
Seating and Safety Restraints • Step 3 must be completed within 50 seconds after the safety belt warning light turns off. 3. For the seating position being disabled, buckle then unbuckle the safety belt 9 times, ending in the unbuckled state. (Step 3 must be completed within 50 seconds after the safety belt warning light turns off.) • After Step 3, the restraint system warning light (airbag light) will be turned on for three seconds. 4.
Seating and Safety Restraints hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a collision be replaced. However, if the collision was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.
Seating and Safety Restraints • Front passenger sensing system • Passenger airbag off indicator light. The airbag supplemental restraints are an integral part of the Personal Safety System. They are designed to be deployed in cases where the Personal Safety System has determined the occupant conditions and crash severity are appropriate to activate these devices. Refer to the Personal Safety System section in this chapter.
Seating and Safety Restraints • Recline the seat slightly one or two degrees from the upright position. Do not put anything on or over the airbag cover (1). Placing objects on or over the airbag cover may cause those objects to be thrown by the airbag into your face and torso or may result in a failure of the airbag to inflate properly, both of which could result in serious injury. Do not attempt to service, repair, or modify the airbag supplemental restraint systems or its fuses.
Seating and Safety Restraints Children and airbags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seat than in the front seat. Failure to follow these instructions may increase the risk of injury in a collision. Airbags can kill or injure a child in a child seat.
Seating and Safety Restraints How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Airbags are designed to inflate in frontal and near-frontal collisions, not rollover, side-impact, or rear-impacts.
Seating and Safety Restraints If the airbag has deployed, the airbag will not function again and must be replaced immediately. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision. Determining if the system is operational The SRS uses readiness lights in the instrument cluster or a tone to indicate the condition of the system. Refer to Airbag readiness in the Instrument Cluster chapter. Routine maintenance of the airbag is not required.
Seating and Safety Restraints The front passenger sensing system will disable (will not inflate) the front passenger’s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects in the front seat, • the system determines that an infant is present in a rear-facing infant seat that is installed according to the manufacturer’s instructions, • the system determines that a small child is present in a forward-facing child restraint that is installed according to the manufacturer’s in
Seating and Safety Restraints • When the front passenger sensing system enables the front passenger frontal airbag (may inflate), the indicator will be unlit and stay unlit. If a person of adult size is sitting in the front passenger’s seat, but the ⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator lamp is lit, it is possible that the person isn’t sitting properly in the seat. If this happens: • Turn the vehicle off and ask the person to place the seatback in the full upright position.
Seating and Safety Restraints The front passenger sensing system may detect small or medium objects placed on the seat cushion. For most objects that are in the front passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the ⬙pass airbag off⬙ lamp may or may not be illuminated according to the table below. Objects Pass Airbag Off Indicator Lamp Unlit Small (i.e. 3 ring binder, small purse, bottled water) Medium (i.e.
Seating and Safety Restraints SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children (generally children who are four years old or younger and who weigh 40 lb.
Seating and Safety Restraints Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly, which could increase the risk of serious injury in a crash.
Seating and Safety Restraints Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child’s head (top of ear level) above the top of the seat.
Seating and Safety Restraints Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder. The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably close to the neck and a shoulder belt that could slip off the shoulder.
Seating and Safety Restraints Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle.
Seating and Safety Restraints • LATCH lower anchors are recommended for use by children up to 22 kg (48 pounds) in a child restraint. Top tether anchors can be used for children up to 27 kg (60 pounds) in a child restraint, and to provide upper torso restraint for children up to 36 kg (80 pounds) using an upper torso harness and a belt-positioning booster. Ford recommends the use of a child safety seat having a top tether strap.
Seating and Safety Restraints 1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted.
Seating and Safety Restraints 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard. 6. Allow the belt to retract.
Seating and Safety Restraints 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward. There should be no more than one inch of movement for proper installation. 10.
Seating and Safety Restraints 2. If the center lap/shoulder safety belt has been disconnected from the seat to carry large cargo behind the seat, reconnect it by buckling the small buckle on the end of the belt into the mini-buckle on the driver’s side. Airbags can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back. Rear facing child seats should NEVER be placed in front of an active airbag. 3. Slide the tongue up the webbing.
Seating and Safety Restraints 5. Insert the belt tongue into the proper buckle for that seating positions until you hear a snap and feel it latch. Make sure the tongue is securely latched to the buckle by pulling on the tongue. 6. While pushing down with your knee on the child seat pull up on the shoulder belt portion to tighten the lap belt portion of the combination lap and shoulder belt. 7.
Seating and Safety Restraints 9. Check from time to time to be sure that there is no slack in the lap/shoulder belt. The shoulder belt must be snug to keep the lap belt tight during a collision. Installing child safety seats in the front row lap belt seating positions (SuperCab and SuperCrew) Installing a child safety seat in the front row lap seating position should be avoided if at all possible. The passenger sensing system does not recognize child seats in the front center seating position.
Seating and Safety Restraints The passenger seats of your vehicle are equipped with built-in tether strap anchors located behind the seats as described below. The tether anchors in your vehicle may be loops of webbing above the seatback or an anchor bracket behind the seat on the rear edge of the seat cushion. The rear seat in the SuperCab and SuperCrew has three straps along the top of the seatback that function as both routing loops for the tether straps and anchor loops.
Seating and Safety Restraints • You may need to pull the seatback forward to access the tether anchors. Make sure the seatback is locked in the upright position before installing the child seat. 4. Clip the tether strap to the anchor as shown. • Front seat Regular Cab passenger side • Front seat Regular Cab center (located on back panel) If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5.
Seating and Safety Restraints If the safety seat is not anchored properly, the risk of a child being injured in a collision greatly increases. Rear seat tether strap attachment There are three loops of webbing just above the back of the rear seat (along the bottom edge of the rear window) in the SuperCab and SuperCrew. These loops are to be used as both routing loops and anchor loops for up to three child safety seat tether straps.
Seating and Safety Restraints 2. Route the tether strap behind the head restraint supports to a loop behind an adjacent seating position, and hook the strap hook onto the loop. If using the driver’s side, pass the strap behind the shoulder belt mounting for the center seat. • Always put the tether strap through the routing loop. The head restraint support post will hold the child seat tightly, but the head restraint post is not strong enough to hold the child seat during a collision. 3.
Seating and Safety Restraints Your vehicle is equipped with LATCH anchors for child seat installation at the following seating positions (LATCH is not available on F150 Regular cab) : • F150 SuperCab and SuperCrew The anchors on both sides of the center of the rear seat are provided for child seats at the outboard seats, and are further apart than the pairs of lower anchors for child seat installation at other seats.
Seating and Safety Restraints If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat. Keeping the child seat just touching the vehicle seat gives the best protection in a severe crash. Each time you use the safety seat, check that the seat is properly attached to the lower anchors and tether anchor.
Tires, Wheels and Loading NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Utility vehicles have a significantly higher rollover rate than other types of vehicles.
Tires, Wheels and Loading Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary. Information on transfer case operation and shifting procedures can be found in the Driving chapter. Information on transfer case maintenance can be found in the Maintenance and Specifications chapter. You should become thoroughly familiar with this information before you operate your vehicle.
Tires, Wheels and Loading • Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car.
Tires, Wheels and Loading Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Tires, Wheels and Loading Glossary of tire terminology • Tire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry. • Tire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code. • Inflation pressure: A measure of the amount of air in a tire.
Tires, Wheels and Loading Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company.
Tires, Wheels and Loading drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or Tire Label. To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never “bleed” or reduce air pressure.
Tires, Wheels and Loading tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Also inspect the tire sidewalls for cracking, cuts, bruises and other signs of damage or excessive wear. If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced. For your safety, tires that are damaged or show signs of excessive wear should not be used because they are more likely to blow out or fail.
Tires, Wheels and Loading U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters “DOT” and indicates that the tire meets all federal standards.
Tires, Wheels and Loading When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below. If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi greater than the maximum pressure on the tire sidewall, the following precautions must be taken to protect the person mounting the tire: 1.
Tires, Wheels and Loading If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Highway hazards No matter how carefully you drive there’s always the possibility that you may eventually have a flat tire on the highway.
Tires, Wheels and Loading • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (AWD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar spare tire/wheel.
Tires, Wheels and Loading Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the Tire and Rim Association (T&RA), that may be used for service on cars, SUVs, minivans and light trucks.
Tires, Wheels and Loading Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186 mph (299 km/h) Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR.
Tires, Wheels and Loading 12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (11⁄2) times as well on the government course as a tire graded 100. • Traction: The traction grades, from highest to lowest are AA, A, B, and C.
Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Range/Load Inflation Limits: Indicates the tire’s load-carrying capabilities and its inflation limits. 3. Maximum Load Dual lb.
Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the Tire and Rim Association (T&RA), that is intended for temporary service on cars, SUVs, minivans and light trucks. 2.
Tires, Wheels and Loading TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
Tires, Wheels and Loading Changing tires with TPMS Each road tire is equipped with a tire pressure sensor fastened to the inside rim of the wheel. The pressure sensor is covered by the tire and is not visible unless the tire is removed. The pressure sensor is located opposite (180 degrees) from the valve stem. Care must be taken when changing the tire to avoid damaging the sensor. It is recommended that you always have your tires serviced by an authorized dealer.
Tires, Wheels and Loading When you believe your system is not operating properly The main function of the Tire Pressure Monitoring System is to warn you when your tires need air. It can also warn you in the event the system is no longer capable of functioning as intended. Please refer to the following chart for information concerning your Tire Pressure Monitoring System: Low Tire Pressure Possible cause Customer Action Required Warning Light Solid Warning Light Tire(s) 1.
Tires, Wheels and Loading Low Tire Pressure Possible cause Customer Action Required Warning Light Flashing Warning Spare tire in use Your temporary spare tire is in Light use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality. For a description of how the system functions under these conditions, refer to When your temporary spare tire is installed in this section.
Tires, Wheels and Loading any tire is under-inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure. SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains.
Tires, Wheels and Loading Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver’s door (vehicles exported outside the US and Canada may not have a Tire Label).
Tires, Wheels and Loading Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
Tires, Wheels and Loading GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The total load on each axle must never exceed its GAWR. Note: For trailer towing information refer to Trailer towing found in this chapter or the RV and Trailer Towing Guide provided by your authorized dealer.
Tires, Wheels and Loading GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing vehicle’s braking system is rated for operation at GVWR, not at GCWR.
Tires, Wheels and Loading Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4.
Tires, Wheels and Loading transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 – (2 x 220) – (12 x 100) = 1400 – 440 – 1200 = – 240 lb. No, you do not have enough cargo capacity to carry that much weight. In metric units, the calculation would be: 635 kg — (2 x 99 kg) — (12 x 45 kg) = 635 — 198 — 540 = —103 kg. You will need to reduce the load weight by at least 240 lb. (104 kg). If you remove 3-100 lb.
Tires, Wheels and Loading Towing a trailer places an additional load on your vehicle’s engine, transmission, axle, brakes, tires and suspension. Inspect these components carefully periodically during, and after any towing operation. Exceeding the maximum GCWR could result in extensive damage to your vehicle and personal injury. Do not exceed the GVWR or the GAWR specified on the certification label.
Tires, Wheels and Loading Regular Cab 4x2 (144.5” wheelbase) Rear axle ratio Maximum Maximum GCWR-lb. (kg) trailer weight-lb. (kg) 4.2L (with 3.55 10000 (4536) 5000 (2268) automatic 3.73 10500 (4763) 5500 (2495) transmission) 4.6L 3.55 11700 (5307) 6700 (3039) 4.6L 3.73 12200 (5534) 7200 (3266) 5.4L 3.55 14000 (6350) 8800 (3992) 5.4L 3.73 15000 (6804) 9800 (4445) 5.4L Heavy Duty 4.10 15300 (6940) 10500 (4763) Engine Regular Cab 4x4 (126” wheelbase) Engine Rear axle ratio Maximum Maximum GCWR-lb.
Tires, Wheels and Loading Regular Cab 4x4 (144.5” wheelbase) Rear axle ratio Maximum Maximum GCWR-lb. (kg) trailer weight-lb. (kg) 5.4L (with 17” 3.55 14000 (6350) 8500 (3856) tires) 5.4L (with 18” 3.55 13500 (6123) 8000 (3629) or 20” tires) 5.4L (with 17” 3.73 15000 (6804) 9500 (4309) tires) 5.4L (with 18” 3.73 14500 (6577) 9000 (4082) or 20” tires) 5.4L Heavy Duty 4.10 15300 (6940) 9500 (4309) Engine SuperCab 4x2 (132.5” wheelbase) Rear axle ratio Maximum GCWR-lb. (kg) Engine 4.6L (with tires) 4.
Tires, Wheels and Loading Engine 4.6L (with 17” tires) 4.6L (with 18” tires) 4.6L (with 17” tires) 4.6L (with 18” tires) 5.4L (with 17” tires) 5.4L (with 18” or 20” tires) 5.4L (with 17” tires) 5.4L (with 18”or 20” tires) Engine 5.4L Heavy Duty Engine 4.6L (with 17” tires) 4.6L (with 18” tires) SuperCab 4x2 (144.5” wheelbase) Rear axle ratio Maximum GCWR-lb. (kg) 3.55 11700 (5307) Maximum trailer weight-lb. (kg) 6500 (2948) 3.55 11200 (5081) 6000 (2722) 3.73 12200 (5534) 7000 (3175) 3.
Tires, Wheels and Loading SuperCab 4x4 (132.5” wheelbase) Rear axle ratio Maximum GCWR-lb. (kg) Engine 4.6L (with tires) 4.6L (with tires) 5.4L (with tires) 5.4L (with tires) 5.4L (with tires) 5.4L (with tires) 17” 3.73 12000 (5443) Maximum trailer weight-lb. (kg) 6500 (2948) 18” 3.73 11500 (5216) 6000 (2721) 17” 3.55 13000 (5897) 7300 (3311) 18” 3.55 12500 (5670) 6800 (3084) 17” 3.73 13500 (6123) 7800 (3538) 18” 3.73 13000 (5897) 7300 (3311) Engine 4.6L (with 17” tires) 4.
Tires, Wheels and Loading Engine 5.4L (with 18” or 20” tires) Engine 5.4L Heavy Duty Engine 4.6L (with 17” tires) 4.6L (with 18” or 20” tires) 4.6L (with 17” tires) 4.6L (with 18” or 20” tires) 5.4L (with 17” tires) 5.4L (with 18” or 20” tires) 5.4L (with 17” tires) 5.4L (with 18” or 20” tires) SuperCab 4x4 (144.5” wheelbase) Rear axle ratio Maximum GCWR-lb. (kg) 3.73 14500 (6577) SuperCab 4x4 (163” wheelbase) Rear axle ratio Maximum GCWR-lb. (kg) 4.10 15300 (6940) Crew Cab 4x2 (138.
Tires, Wheels and Loading Crew Cab 4x2 (138.5” wheelbase) Harley-Davidson Version Engine Rear axle ratio Maximum Maximum GCWR-lb. (kg) trailer weight-lb. (kg) 5.4L 3.73 11000 (4990) 5300 (2404) Engine 4.6L (with 17” tires) 4.6L (with 18” tires) 5.4L (with 17” tires) 5.4L (with 18” or 20” tires) 5.4L (with 17” tires) 5.4L (with 18” or 20” tires) Crew Cab 4x4 (138.5” wheelbase) Rear axle ratio Maximum GCWR-lb. (kg) 3.73 12200 (5534) Maximum trailer weight-lb. (kg) 6600 (2994) 3.
Tires, Wheels and Loading Engine 4.6L (with 18” or 20” tires) 4.6L (with 17” tires) 4.6L (with 18” or 20” tires) 5.4L (with 17” tires) 5.4L (with 18” or 20” tires) 5.4L (with 17” tires) 5.4L (with 18” or 20” tires) Engine 4.6L (with 17” tires) 4.6L (with 18” tires) 5.4L (with 17” tires) 5.4L (with 18” or 20” tires) 5.4L (with 17” tires) 5.4L (with 18” or 20” tires) Crew Cab 4x2 (150.5” wheelbase) Rear axle ratio Maximum GCWR-lb. (kg) 3.55 11200 (5080) Maximum trailer weight-lb. (kg) 5700 (2585) 3.
Tires, Wheels and Loading Trailer frontal area considerations: • Not to exceed towing vehicle frontal area without Class IV trailer towing package • Not to exceed 60 square feet (5.52 square meters) with Class IV trailer towing package Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle. See your authorized dealer or a reliable trailer dealer if you require assistance.
Tires, Wheels and Loading Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase.
Tires, Wheels and Loading • Do not exceed the GCWR rating or transmission damage may occur. Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your Scheduled Maintenance Information for more information. Trailer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination.
Tires, Wheels and Loading Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability, emissions and reliability. Replace the rear axle lubricant any time the axle has been submerged in water. Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair required. RECREATIONAL TOWING Follow these guidelines if you have a need for recreational towing.
Tires, Wheels and Loading Vehicles equipped with automatic transmission and 4x4 vehicles equipped with an electronic-shift transfer case: • Release the parking brake. • Turn the key in the ignition to the OFF position. • Place the transmission in N (Neutral). • Do not exceed a distance of 50 miles (80 km). • Do not exceed 35 mph (56 km/h) vehicle speed. • The vehicle must be towed in the forward position to ensure no damage is done to the internal transfer case components.
Driving STARTING Positions of the ignition 1. OFF/LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. Note: The ignition key cannot be removed from the ignition unless the gearshift lever is securely latched in P (Park). 2. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 4. START, cranks the engine.
Driving Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM).
Driving • Make sure the parking brake is set. BRAKE If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor 3. Turn the key to 3 (ON) without turning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights.
Driving Starting the engine 1. Turn the key to 3 (ON) without turning the key to 4 (START). If there is difficulty in turning the key, rotate the steering wheel until the key turns freely. 2. Turn the key to 4 (START), then release the key as soon as the engine starts. Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again.
Driving If the engine fails to start using the preceding instructions (flexible fuel vehicles only) 1. Press and hold down the accelerator 1/3 to 1/2 way to floor, then crank the engine. 2. When the engine starts, release the key, then gradually release the accelerator pedal as the engine speeds up. If the engine still fails to start, repeat Step 1. Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects.
Driving Refer to Brake system warning light in the Instrument Cluster chapter for information on the brake system warning light. Base, Base with Tachometer and Family Carrier instrument ! cluster BRAKE Mid, Luxury and Harley-Davidson instrument cluster ! P BRAKE Four-wheel anti-lock brake system (ABS) Your vehicle is equipped with an Anti-lock Braking System (ABS). This system helps you maintain steering control during emergency stops by keeping the brakes from locking.
Driving Base, Base with Tachometer and Family Carrier instrument cluster Mid, Luxury and Harley-Davidson instrument cluster ! BRAKE ! P BRAKE Parking brake To set the parking brake (1), press the parking brake pedal down until the pedal stops. The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released.
Driving TRACTION CONTROL姟 (IF EQUIPPED) Your vehicle may be equipped with a Traction Control娂 system. This system helps you maintain the stability and steerability of your vehicle, especially on slippery road surfaces such as snow- or ice-covered roads and gravel roads. The system will allow your vehicle to make better use of available traction in these conditions.
Driving STEERING To help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until it stops) for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering fluid level (below the MIN mark on the reservoir). • Some noise is normal during operation. If the noise is excessive, check for a low power steering fluid level before seeking service by your authorized dealer.
Driving PREPARING TO DRIVE Utility vehicles have a significantly higher rollover rate than other types of vehicles. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Your vehicle has larger tires and increased ground clearance, giving the vehicle a higher center of gravity than a passenger car. Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity.
Driving 2. Locate the round access plug on the underside of the steering column cover. 3. Remove the access plug using a flat head screwdriver, then push the override button using a flat head screwdriver, apply the brake pedal and shift the transmission into N (Neutral). 4. Reinstall the access plug cover, start the vehicle and release the parking brake. Do not drive your vehicle until you verify that the brakelamps are working.
Driving 2. Open the center console bin. Using a screwdriver, carefully pry off the console finish panel surrounding the shifter mechanism by inserting a screwdriver into the latch slot as shown. 3. Remove console finish panel assembly to expose the inside of the gearshift. 4. Press and hold the white button located along side the shifter housing assembly (as shown in the illustration).
Driving Understanding the gearshift positions of the 4–speed automatic transmission Your vehicle’s automatic transmission is equipped with a special shift strategy that insures maximum heater performance during cold weather operation. When ambient temperature is 23°F (–5°C) or below and the engine coolant temperature is below 100°F (38°C), light throttle upshifts may be slightly delayed. Once the engine coolant temperature reaches 160°F (71°C) the normal shift strategy will resume.
Driving To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse).
Driving • Floor-shift transmission The transmission control indicator (TCIL) will illuminate on the instrument cluster. O/D OFF Drive (not shown) Drive is activated when the transmission control switch is pressed. • This position allows for all forward gears except overdrive. • O/D OFF lamp is illuminated. • Provides engine braking. • Use when driving conditions cause excessive shifting from O/D to other gears.
Driving • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds. Forced downshifts • Allowed in D (Overdrive) or Drive. • Depress the accelerator to the floor. • Allows transmission to select an appropriate gear. If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow, it may be rocked out by shifting between forward and reverse gears, stopping between shifts in a steady pattern.
Driving During each shift, the clutch pedal must be fully depressed to the floor. Make sure the floor mat is properly positioned so it doesn’t interfere with the full extension of the clutch pedal. Failure to fully depress the clutch pedal to the floor may cause increased shift efforts, prematurely wear transmission components or damage the transmission. Do not drive with your foot resting on the clutch pedal or use the clutch pedal to hold your vehicle at a standstill while waiting on a hill.
Driving Maximum downshift speeds1 Shift from: Transfer case position (if equipped) 2H or 4H 4L 55 mph (89 km/h) 21 mph (34 km/h) D (Overdrive) - 4 4-3 45 mph (72 km/h) 17 mph (27 km/h) 3-2 35 mph (56 km/h) 13 mph (21 km/h) 2-1 20 mph (32 km/h) 7 mph (11 km/h) 1 Downshift at lower speeds when driving on slippery surfaces. Reverse 1. Make sure that your vehicle is at a complete stop before you shift into R (Reverse). Failure to do so may damage the transmission. 2.
Driving To help avoid personal injury, always use caution when in reverse and when using the RSS. This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground.
Driving The RSS automatically turns on when the gearshift lever is placed in R (Reverse) and the ignition is ON. An RSS control allows the driver to turn the RSS on and off. To turn the RSS off, the ignition must be ON, and the gear selector in R (Reverse). An indicator light on the control will illuminate when the system is turned off. If the indicator light illuminates when the RSS is not turned off, it may indicate a failure in the RSS.
Driving • 4X4 LOW – Momentarily illuminates when the engine is started. Illuminates when 4L is selected. 4x4 LOW Using a manual 4WD system (if equipped) 2H 4H N 4L 2H (2WD High) – Power to the rear wheels only; used for street and highway driving. Provides optimal smoothness and fuel economy at high speeds. 4H (4WD High) – Used for extra traction such as in snow or icy roads or in off-road situations. Not intended for use on dry pavement. N (Neutral) – No power to either front or rear wheels.
Driving • If the transfer case will not engage into 4L (4WD Low), allow the vehicle to coast at a speed below 3 mph (5 km/h), then repeat Steps 2 and 3. Note: Some noise may be heard as the system shifts or engages; this is normal. Note: For proper operation in 4WD Low, ensure the transfer case shift lever is moved entirely rearward in to the 4L (4WD Low) position and that the 4x4 Low light is illuminated.
Driving 4L (4WD Low) - Uses extra gearing to provide maximum power to all four wheels at reduced speeds. Intended only for off-road applications such as deep sand, steep grades or pulling heavy objects. 4L (4WD Low) will not engage while the vehicle is moving above 3 mph (5 km/h); this is normal and should be no reason for concern. Refer to Shifting to/from 4L (4WD Low) for proper operation.
Driving AWD (Auto) - Power delivered to all four wheels, as required, for increased traction. This is appropriate for all on-road driving conditions, such as dry road surfaces, wet pavement, snow, gravel and shallow sand. 4H (Lock) - The “4X4 HI” light will illuminate in the instrument cluster when this position is selected. This position is not recommended for use on dry pavement. This position is only intended for severe winter or off-road conditions, such as deep snow, ice or deep sand.
Driving Basic operating principles • Do not use 4WD on dry, hard surfaced roads. Doing so will produce excessive noise, increase tire wear and may damage drive components. 4WD modes are only intended for consistently slippery or loose surfaces. • Drive slower in strong crosswinds which can affect the normal steering characteristics of your vehicle. • Be extremely careful when driving on pavement made slippery by loose sand, water, gravel, snow or ice.
Driving Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat. Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over-driving” your vehicle, i.e., turn the steering wheel only as rapidly and as far as required to avoid the emergency.
Driving leave the vehicle unattended with the transfer case in the N (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized dealer.
Driving Mud and water If you must drive through high water, drive slowly. Traction or brake capability may be limited. When driving through water, determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly. If the ignition system gets wet, the vehicle may stall. Once through water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes.
Driving Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down. Avoid driving crosswise or turning on steep slopes or hills. A danger lies in losing traction, slipping sideways and possibly rolling over. Whenever driving on a hill, determine beforehand the route you will use.
Driving Driving on snow and ice 4WD vehicles have advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. Should you start to slide while driving on snowy or icy roads, turn the steering wheel in the direction of the slide until you regain control. Avoid sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop. Avoid sudden braking as well.
Driving DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks). When driving through water, traction or brake capability may be limited. Also, water may enter your engine’s air intake and severely damage your engine or your vehicle may stall.
Driving • • • • Ford compliance certification to FMVSS. Exceeding this weight may require the auxiliary equipment installer additional safety certification responsibility. The Front Accessory Reserve Capacity (FARC) is added for customer convenience Rear ballast weight behind the rear axle may be required to prevent exceeding the FGAWR, and provide front-to-rear weight balance for proper braking and steering. Front wheel toe may require re-adjustment to prevent premature uneven tire wear.
Driving Never remove or defeat the “tripping mechanisms” designed into the snow removal equipment by its manufacturer. Doing so may cause damage to the vehicle and the snow removal equipment as well as possible air bag deployment. Do not attempt to service, repair, or modify the air bag supplemental restraint system (SRS) or its fuses. See your Ford or Lincoln Mercury dealer.
Roadside Emergencies ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty.
Roadside Emergencies Canadian customers refer to your Owner Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In the United States, this card is found in the Owner Guide portfolio in the glove compartment.
Roadside Emergencies HAZARD FLASHER The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it when your vehicle is disabled and is creating a safety hazard for other motorists.
Roadside Emergencies This switch is located in the front passenger’s footwell, behind the kick panel access cover, to the left of the fuse box. The access cover needs to be removed to reset the fuel pump shut-off switch. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. Turn the ignition ON. 5. Wait a few seconds and return the key to OFF. 6. Make another check for leaks.
Roadside Emergencies Standard fuse amperage rating and color COLOR Cartridge Fuse link maxi cartridge fuses 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.
Roadside Emergencies Always disconnect the battery before servicing high current fuses. To reduce risk of electrical shock, always replace the cover to the Power Distribution Box and Auxiliary Relay Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter.
Roadside Emergencies The fuses are coded as follows. Fuse/Relay Location 1 Fuse Amp Rating 10A* 2 20A* 3 7.5A* 4 10A* 5 7.
Roadside Emergencies Fuse/Relay Location 14 Fuse Amp Rating 10A* 15 5A* 16 17 18 10A* 15A* 10A* 19 20 10A* 10A* 21 22 15A* 10A* 23 24 10A* 15A* 25 26 27 10A* 20A* 5A* 28 5A* 248 2007 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Passenger Compartment Fuse Panel Description Back-up lamp and Daytime Running Lamps (DRL) relay coil, A/C pressure switch, Redundant speed control switch, Heated PCV (5.
Roadside Emergencies Fuse/Relay Location 29 30 31 Fuse Amp Rating 15A* 15A* 20A* 32 15A* 33 15A* 34 35 15A* 20A* 36 37 10A* 20A* 38 39 40 41 25A* 20A* 20A* 20A* 42 101 102 103 10A* 30A** 20A** 20A** Passenger Compartment Fuse Panel Description PCM 4x4 power PCM 4x4 power Radio power, Satellite radio module Vapor Management Valve (VMV), A/C clutch relay, Canister vent, Heated Exhaust Gas Oxygen (HEGO) sensors #11 and #21, CMCV, Mass Air Flow (MAF) sensor, VCT, Heated Positive Crankcase Ventilat
Roadside Emergencies Fuse/Relay Location 104 105 106 107 108 109 Fuse Amp Rating — 30A** 30A** 30A** 30A** 30A** 110 111 112 113 114 — 30A** 40A** 30A** 40A** 115 116 117 118 401 20A** 30A** — 30A** 30A Circuit breaker R01 Full ISO relay R02 Full ISO relay R03 Full ISO relay R04 Full ISO relay R05 Full ISO relay R06 Full ISO relay R201 Half ISO relay R202 Half ISO relay R203 Half ISO relay * Mini fuses ** Cartridge fuses 250 2007 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Passenger Compartm
Roadside Emergencies Auxiliary relay box The relay box is located in the engine compartment on the left fender.
Roadside Emergencies CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Note: If your vehicle is equipped with the tire pressure monitoring system (TPMS), the indicator light will illuminate when the spare tire is in use.
Roadside Emergencies 2.
Roadside Emergencies • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare t
Roadside Emergencies Removing the spare tire 1. Use the ignition key to remove the lock cylinder from the access hole of the bumper to allow access to the guide tube. Assemble the jack handle as shown in the illustration. 2. Fully insert the jack handle through the bumper hole and into the guide tube through the access hole in the rear bumper. 3. Turn the handle counterclockwise until tire is lowered to the ground, the tire can be slid rearward and the cable is slightly slack. 4.
Roadside Emergencies 1. Park on a level surface, activate hazard flashers and set the parking brake. 2. Place gearshift lever in P (Park) and turn engine OFF. BRAKE 3. Block the diagonally opposite wheel. 4. Obtain the spare tire and jack from their storage locations. 5. Use the tip of the lug wrench to remove any wheel trim. 6. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 7.
Roadside Emergencies • Front Note: Use the frame rail as the jacking location point, NOT the control arm. • Rear To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the front or rear differential as a jacking point. 8. Remove the lug nuts with the lug wrench. 9.
Roadside Emergencies 11. Remove the jack and fully tighten the lug nuts in the order shown (Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification): • Six lug nut wheel • Seven lug nut wheel 12. Stow the flat tire. Refer to Stowing the flat/spare tire. 13. Stow the jack and lug wrench. Make sure the jack is fastened so it does not rattle when you drive. 14. Unblock the wheels.
Roadside Emergencies ratchets or slips with little effort, take the vehicle to your authorized dealer for assistance at your earliest convenience. 4. Check that the tire lies flat against the frame and is properly tightened. Try to push or pull, then turn the tire to be sure it will not move. Loosen and retighten, if necessary. Failure to properly stow the spare tire may result in failure of the winch cable and loss of the tire. 5.
Roadside Emergencies Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your automatic transmission vehicle. Automatic transmissions do not have push-start capability. Attempting to push-start a vehicle with an automatic transmission may cause transmission damage. Preparing your vehicle When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy.
Roadside Emergencies 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.
Roadside Emergencies + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5.
Roadside Emergencies Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. Ford recommends your vehicle be towed with a wheel lift or flatbed. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Customer Assistance GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all authorized dealers are authorized to perform all warranty repairs.
Customer Assistance In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealer to help you.
Customer Assistance In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws.
Customer Assistance THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the Warranty Guide. However, if your warranty concern has not been resolved using the three-step procedure, you may be eligible to participate in the BBB AUTO LINE program.
Customer Assistance UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Customer Assistance If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www.ford-esp.com. GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate.
Customer Assistance ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATED P.O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.com. (Items in this catalog may be purchased by credit card, check or money order.
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight.
Cleaning • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid Wax (ZC-53-A), which is available from your authorized dealer, or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time.
Cleaning ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean.
Cleaning • 5.4L engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and Tar Remover (ZC-42). • For plastic headlamp lenses, use Motorcraft Ultra Clear Spray Glass Cleaner (ZC-23).
Cleaning • The wiper blades can be cleaned with isopropyl (rubbing) alcohol or Motorcraft Premium Windshield Washer Concentrate (ZC-32–A), available from your authorized dealer. This washer fluid contains special solution in addition to alcohol which helps to remove the hot wax deposited on the wiper blade and windshield from automated car wash facilities. Be sure to replace wiper blades when they appear worn or do not function properly. • Do not use abrasives, as they may cause scratches.
Cleaning INSTRUMENT PANEL AND CONSOLE (HARLEY-DAVIDSON EDITION ONLY) Your vehicle’s instrument panel and console are uniquely painted with both high and low gloss paints that require special care. The high gloss area is similar to that of the vehicle’s exterior; the low gloss area is designed to help protect the driver from undesirable windshield reflection.
Cleaning INTERIOR TRIM • Clean the interior trim areas with a damp cloth, then with a clean, dry cloth; you may also use Motorcraft Dash & Vinyl Cleaner (ZC-38-A). • Do not use household or glass cleaners as these may damage the finish. INTERIOR For fabric, carpets, cloth seats and safety belts: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54).
Cleaning Leather seats for the King Ranch SuperCrew only (if equipped) Your vehicle is equipped with seating covered in premium, top-grain leather which is extremely durable, but still requires special care and maintenance in order to ensure longevity and comfort. Regular cleaning and conditioning will maintain the appearance of the leather. Failure to care for the leather can result in drying out and fading of the material.
Cleaning Conditioning Bottles of King Ranch Leather Conditioner are available at the King Ranch Saddle Shop. Visit the Web site at www.krsaddleshop.com, or telephone (in the United States) 1–800–282–KING (5464). If you are unable to obtain King Ranch Leather Conditioner, use another premium leather conditioner. • Apply your first conditioning treatment within six months of taking delivery of your vehicle.
Cleaning Motorcraft Motorcraft Motorcraft Motorcraft Motorcraft Motorcraft Motorcraft Motorcraft Motorcraft Motorcraft Motorcraft Motorcraft Motorcraft Motorcraft Motorcraft Motorcraft Motorcraft Detail Wash (ZC-3–A) Dusting Cloth (ZC-24) Engine Shampoo and Degreaser (U.S. only) (ZC-20) Engine Shampoo (Canada only) (CXC-66-A) One Step Wash and Wax Concentrate (ZC-6-A) Paint Sealant (ZC-45) Premium Car Wash Concentrate (U.S.
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your Warranty Guide/Owner Information Guide to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications.
Maintenance and Specifications To reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located on the front bumper under the grill. 3. Lift the hood until the lift cylinders hold it open.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.2L V6 engine 1 10 2 9 8 3 7 4 5 6 1. Battery 2. Clutch fluid reservoir (manual transmission) 3. Power steering fluid reservoir 4. Brake fluid reservoir 5. Engine coolant reservoir 6. Air filter assembly 7. Engine oil filler cap 8. Engine oil dipstick 9. Transmission fluid dipstick (automatic transmission) 10.
Maintenance and Specifications 4.6L V8 1. Battery 2. Transmission fluid dipstick (automatic transmission) 3. Engine oil filler cap 4. Power steering fluid reservoir 5. Brake fluid reservoir 6. Engine coolant reservoir 7. Air filter assembly 8. Engine oil dipstick 9.
Maintenance and Specifications 5.4L V8 1. Battery 2. Transmission fluid dipstick (automatic transmission) 3. Air filter assembly 4. Power steering fluid reservoir 5. Engine oil dipstick 6. Brake fluid reservoir 7. Engine coolant reservoir 8. Engine oil filler cap 9.
Maintenance and Specifications WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and smearing. Refer to the Maintenance product specifications and capacities section in this chapter.
Maintenance and Specifications Poor wiper quality can be improved by cleaning the wiper blades and the windshield, refer to Windows and wiper blades in the Cleaning chapter. To prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element.
Maintenance and Specifications • 4.6L/5.4L V8 engine 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the lower and upper holes or between the MIN and MAX marks (depending on application), the oil level is acceptable. DO NOT ADD OIL. • 4.
Maintenance and Specifications • 4.6L/5.4L V8 engine • If the oil level is below the lower hole or the MIN mark, add enough oil to raise the level within the lower and upper holes or within the MIN-MAX range. • Oil levels above the upper hole or the MAX mark may cause engine damage. Some oil must be removed from the engine by an authorized dealer. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil.
Maintenance and Specifications Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers.
Maintenance and Specifications BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals.
Maintenance and Specifications Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.
Maintenance and Specifications R TU LE AD RE N • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. RECYCLE ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in scheduled maintenance information.
Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter.
Maintenance and Specifications Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • Add Motorcraft Premium Gold Engine Coolant or equivalent meeting Ford specification WSS-M97B51-A1. Refer to Maintenance product specifications and capacities in this chapter.
Maintenance and Specifications 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (an opaque plastic bottle). Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5.
Maintenance and Specifications Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely cold climates (less than –34° F [–36° C ]): • It may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.
Maintenance and Specifications How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the red (hot) area. • The mini message center (if equipped) will indicate “Check Gauges”, refer to Warning Lights and Chimes in the Instrument Cluster chapter. • The message center (if equipped) will indicate a system warning, refer to Message Center in the Driver Controls chapter. • The light will illuminate.
Maintenance and Specifications Never remove the coolant reservoir cap while the engine is running or hot. 5. Restart the engine and take your vehicle to an authorized dealer. Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to an authorized dealer as soon as possible. FUEL FILTER For fuel filter replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter.
Maintenance and Specifications Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuels such as gasoline and ethanol are highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent.
Maintenance and Specifications Pure ethanol is the alcohol which is the intoxicating agent in liquor, beer and wine. It is distilled from the fermentation of plants such as field corn and sugar cane. When ethanol is produced for use in motor fuels, a small amount of gasoline is added to make it unfit for beverage use. The resulting ethanol blend is called denatured fuel ethanol meaning that it is denatured with 2% to 5% gasoline and is suitable for automotive use.
Maintenance and Specifications Refueling • • • • • • Fuel vapor burns violently and a fuel fire can cause severe injuries.
Maintenance and Specifications If the digital display reads “CHECK FUEL CAP” and stays on after you start the engine, the fuel filler cap may not be properly installed. Turn off the engine, remove the fuel filler cap, align the cap properly and reinstall it. If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle.
Maintenance and Specifications Your vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based additives. Studies indicate that these additives can cause your vehicle’s emission control system to deteriorate more rapidly. In Canada, premium grade fuel generally contains more metallic additives than regular grade fuel. We recommend using regular grade fuel.
Maintenance and Specifications Fuel quality Many of the world’s automakers approved the World-wide Fuel Charter that recommends gasoline specifications to provide improved performance and emission control system protection for your vehicle. Gasolines that meet the World-wide Fuel Charter should be used when available. Ask your fuel supplier about gasolines that meet the World-wide Fuel Charter. Do not add aftermarket fuel additive products to your fuel tank.
Maintenance and Specifications If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal. • Normally, adding one gallon of fuel is enough to restart the engine. If the vehicle is out of fuel and on a steep grade, more than one gallon may be required. • The indicator may come on.
Maintenance and Specifications • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow no more than three automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the same direction each time you fill up. • Have the vehicle loading and distribution the same every time.
Maintenance and Specifications • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy. • Slow down gradually. • Driving at reasonable speeds (traveling at 55 mph [88 km/h] uses 15% less fuel than traveling at 65 mph [105 km/h]). • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy.
Maintenance and Specifications • Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 km) of driving. • Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain. • Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. • Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation.
Maintenance and Specifications Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the indicator, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power could indicate that the emission control system is not working properly.
Maintenance and Specifications These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel, properly tightening the fuel cap or letting the electrical system dry out. After three driving cycles without these or any other temporary malfunctions present, the indicator should stay off the next time the engine is started. A driving cycle consists of a cold engine startup followed by mixed city/highway driving. No additional vehicle service is required.
Maintenance and Specifications Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. If the vehicle is still not ready for I/M testing, the above driving cycle will have to be repeated. POWER STEERING FLUID Check the power steering fluid.
Maintenance and Specifications CLUTCH FLUID (IF EQUIPPED) Check the fluid level. Refer to scheduled maintenance information for the service interval schedules. During normal operation, the fluid level in the clutch reservoir should remain constant. If the fluid level drops, refill the fluid level to the step in the reservoir. Use only a DOT 3 brake fluid designed to meet Ford specifications. Refer to Maintenance product specifications and capacities in this chapter.
Maintenance and Specifications TRANSMISSION FLUID Checking automatic transmission fluid (if equipped) Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, i.e., if the transmission slips or shifts slowly or if you notice some sign of fluid leakage. Automatic transmission fluid expands when warmed.
Maintenance and Specifications You can check the fluid without driving if the ambient temperature is above 50°F (10°C). However, if fluid is added at this time, an overfill condition could result when the vehicle reaches normal operating temperature. The transmission fluid should be in this range if at normal operating COLD 5L 3P -7A020- CB FoMoCo temperature (150°F-170°F [66°C-77°C]). The transmission fluid should be in this range if at ambient temperature (50°F-95°F [10°C-35°C]).
Maintenance and Specifications If an overfill occurs, excess fluid should be removed by an authorized dealer. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. COLD FoMoCo 5L 3P -7A020- CB Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components.
Maintenance and Specifications 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Maintenance product specifications and capacities section in this chapter. TRANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level.
Maintenance and Specifications 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Maintenance product specifications and capacities section in this chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication. Refer to the scheduled maintenance information for maintenance intervals.
Maintenance and Specifications Changing the air filter element • 4.2L/4.6L engines 1. Loosen the clamp that secures the air filter element in place. 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the open end of the air filter housing. 4. Install a new air filter element. 5. Reassemble the two halves of the air filter housing, aligning the notch and slot found on the top of each half.
Maintenance and Specifications 2. Pull air filter tray assembly out toward front of vehicle and lift air filter element up and out of housing. The air filter box needs to be free of any debris before installing a new air filter. 3. Install a new air filter element into the tray assembly. 4. Return air filter tray to original position by pressing firmly on the handle until all rearward movement stops and secure the two clamps. MOTORCRAFT PART NUMBERS Component 4.
Maintenance and Specifications For PCV valve replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the PCV valve. Replace the PCV valve with one that meets Ford material and design specifications for your vehicle, such as a Motorcraft or equivalent replacement part. The customer warranty may be void for any damage to the emissions system if such a PCV valve is not used. 2 For spark plug replacement, see your authorized dealer.
2007 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) 6.0 quarts (5.7L) 6.0 quarts (5.7L) 7.0 quarts (6.6L) 4.2L engine oil 4.6L engine oil 5.4L engine oil — 3.7 pints (2.0L) Cooling system stop leak pellets Front axle (4X4) 5.4L engine coolant 4.6L engine coolant 17.6 quarts (16.7L) 20.5 quarts (19.4L) 20.9 quarts (19.8L) Fill to line or step (for clutch) on reservoir Brake fluid and clutch fluid 4.
2007 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) XT-2-QDX / MERCON威 XT-5-QM / MERCON威V Motorcraft MERCON威V ATF8 — Motorcraft MERCON威 ATF XG-3-A / ESE-M1C171-A Hinges, latches, striker plates, fuel filler door hinge and door check arm Fill to between MIN and MAX lines on reservoir XG-1-C / ESA-M1C75-B XG-4 or XL-5 / ESB-M1C93-B XY-75W140-QL / WSL-M2C192-A Ford part number / Ford specification Premium Long-Life Grease Multi-Purpose Grease Motorcraft SAE 75W-140 Rear Synthetic Axle Lubrica
Capacity 26.0 gallons (98.4L) — Ford part name or equivalent Motorcraft Premium Windshield Washer Concentrate — ZC-32-A / WSB-M8B16-A2 Ford part number / Ford specification 30 gallons — — (113.6L) 27 gallons Fuel tank SuperCrew (102.2L) Standard — — 6.5’ box 35.7 gallons (135.1L) Optional Fuel tank 27 gallons (102.1L) Standard Reg. Cab 8’ box / — — 35.7 gallons SuperCab 6.5’ box / SuperCab 8’ box (135.1L) Optional 1 Use of synthetic or synthetic blend motor oil is not mandatory.
For 10.25 inch Traction-Lok axles, use 6.5 pints (3.1L) of Motorcraft SAE 75W-140 Synthetic Rear Axle Lubricant and 8 oz. (236 ml) of Additive Friction Modifier XL–3 or equivalent meeting Ford Specification EST-M2C118-A. 5 Your vehicle’s rear axle is filled with a synthetic rear axle lubricant and is considered lubricated for life. These lubricants do not need to be checked or changed unless a leak is suspected, service is required or the axle assembly has been submerged in water.
Maintenance and Specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Ignition system Spark plug gap Compression ratio 4.2L V6 engine 4.6L V8 engine 5.4L V8 engine 256 281 330 87 octane 87 octane 87 octane or Ethanol (E85)2 1-4-2-5-3-6 1-3-7-2-6-5-4-8 1-3-7-2-6-5-4-8 EDIS Coil on plug Coil on plug 0.052–0.056 inch 0.052–0.056 inch 0.040–0.050 inch (1.32–1.42mm) (1.32–1.42mm) (1.02–1.28mm)1 9.3:1 9.37:1 9.85:1 1 The 5.4L 3V spark plug gap can’t be adjusted. 2 5.
Maintenance and Specifications • 4.6L V8 Engine and 5.4L V8 Engine IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structure (B-Pillar) by the trailing edge of the driver’s door or the edge of the driver’s door.
Maintenance and Specifications Vehicle identification number (VIN) The vehicle identification number is located on the driver side instrument panel. Please note that in the graphic, XXXX is representative of your vehicle identification number. XXXXXXXXXXXXXXXXX The Vehicle Identification Number (VIN) contains the following information: 1. World manufacturer identifier 2. Brake system / Gross Vehicle Weight Rating (GVWR) / Restraint System 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6.
Maintenance and Specifications TRANSMISSION/TRANSAXLE CODE DESIGNATIONS You can find a transmission/transaxle code on the Safety Compliance Certification Label. The following table tells you which transmission or transaxle each code represents.
Accessories GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle. In addition, each accessory is made from high quality materials and meets or exceeds Ford’s rigorous engineering and safety specifications.
Accessories Lifestyle Ash cup / smoker’s package Bedliners and bedmats Cargo organization and management Towing mirrors Trailer hitches, wiring harnesses and accessories Peace of mind Mobile-ease娂 hands-free communication system Remote start Vehicle security systems Wheel locks For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weigh
Index A Accessory delay ..........................76 Air cleaner filter ...............320–322 Air conditioning ....................51, 54 Airbag supplemental restraint system ................................140–141 and child safety seats ............143 description ..............................141 disposal ....................................145 driver airbag ....................141, 144 indicator light .........................145 operation .........................141, 144 passenger airbag .............
Index washing ....................................273 waxing .....................................273 wheels ......................................274 wiper blades ............................276 Climate control (see Air conditioning or Heating) ...........................48, 51, 54 Clock adjust 6-CD in dash .............................35 AM/FM Stereo ...........................27 AM/FM/CD .................................29 Clutch fluid ..........................................
Index checking and adding ..............289 dipstick ....................................289 filter, specifications ........292, 322 recommendations ...................292 refill capacities ........................324 specifications ..........................324 Exhaust fumes ..........................212 safety information relating to automotive fuels .....................301 Fuel - flex fuel vehicle (FFV) .........................301, 305–306 Fuel pump shut-off switch .......243 Fuses ...................
Index Illuminated visor mirror .............69 Infant seats (see Safety seats) .....................153 Inspection/maintenance (I/M) testing ........................................313 Instrument panel cleaning ...................................277 cluster ........................................12 lighting up panel and interior .......................................60 J Jack ............................................252 positioning ...............................252 storage ............................
Index Oil (see Engine oil) ..................289 P Parking brake ............................214 Parts (see Motorcraft parts) ....322 Passenger Occupant Classification Sensor .................122 Power distribution box (see Fuses) ...............................245 Power door locks ......................101 Power mirrors .............................77 Power point .................................72 Power steering ..........................216 fluid, checking and adding ....314 fluid, refill capacity ......
Index Spark plugs, specifications .....................322, 328 Special notice ambulance conversions ..............8 four-wheel drive vehicles .......240 utility-type vehicles ....................8 Specification chart, lubricants ...................................324 Speed control ..............................79 Starting a flex fuel vehicle .......211 Starting your vehicle ........................208–209, 211 jump starting ..........................259 Steering wheel controls .............................
Index Windshield washer fluid and wipers ..........................................68 340 2007 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) checking and adding fluid .....288 replacing wiper blades ...........
