Contents Before driving Introduction 2 Instrumentation 5 Controls and features 22 Seating and safety restraints 82 Starting and driving Starting 107 Driving 112 Roadside emergencies 144 Servicing Maintenance and care 169 Capacities and specifications 212 Customer assistance 223 Reporting safety defects 235 Index 236 All rights reserved.
Introduction ICONS Indicates a safety alert. Read the following section on Warnings. Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. Indicates a message regarding child safety restraints. Refer to Seating and safety restraints for more information.
Introduction SPECIAL NOTICES Notice to owners of diesel-powered vehicles Read the 7.3 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for information regarding correct operation and maintenance of your diesel-powered light truck. Notice to owners of utility type vehicles Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car.
Introduction If your vehicle is equipped with the Ford ambulance preparation package, it will be indicated on the Certification label. The label is located on the driver’s side door pillar or on the rear edge of the driver’s door. You can determine whether the ambulance manufacturer followed Ford’s recommendations by directly contacting that manufacturer. Ford Ambulance preparation package is only available on certain 7.3L Diesel engine equipped vehicles.
Instrumentation 5
Instrumentation Instrument cluster (pg. 8) Speed control* (pg. 67) Turn signal and wiper/washer control (pg. 72) 40 FUEL FILL LOW FUEL F 30 50 60 80 100 E 20 40 ! H - + 18 C 8 P 10 0 80 FUEL RESET 000000 140 L BRAKE 4 2 120 H 3 70 60 90 5 1 20 ABS 160 MPH 0 0 0 0 km/h P RN D 100 0 RPM X1000 21 SERVICE ENGINE SOON 6 LOW RANGE 4X4 PANEL DIM O RES ON SET ACCEL OFF COAST Headlamp control (pg. 22) Instrument panel dimmer switch (pg.
Instrumentation Gearshift lever (pg. 116) Electronic sound system (pg. 29) VOL - PUSH ON FM1 AM FM BASS TREB BAL SEEK SCAN TUNE VE RDRI OVE ST EJ w TAPE CD DISCS REW FF 1 SIDE 1-2 2 3 FADE AUTO SET 4 COMP SHUFFLE 5 6 4X4 4X4 WD HIGH LOW PASSENGER AIR BAG OFF OFF ON A/C MAX A/C Climate control system (pg. 24) Passenger air bag deactivate switch (pg. 96) OFF Auxiliary power point (pg. 24) 4WD control * (pg.
Instrumentation WARNING LIGHTS AND CHIMES F 50 40 FUEL FILL LOW FUEL 60 120 E 20 40 ! H - + 18 C 8 10 0 80 000000 140 L BRAKE 4 2 100 60 H 3 70 80 30 90 5 1 20 ABS 160 MPH 0 0 0 0 km/h P RN D 21 100 0 RPM X1000 SERVICE ENGINE SOON 6 DOOR AJAR LOW RANGE 4X4 Low fuel Illuminates as an early reminder of a low fuel condition indicated on the LOW fuel gauge.
Instrumentation What you should do if the Check Engine/Service Engine Soon light illuminates Light turns on solid: This means that the OBD I system has detected a malfunction. Temporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly.) 2. Poor fuel quality or water in the fuel. These and other temporary malfunctions can be corrected by filling the fuel tank with good quality fuel.
Instrumentation What you should do if the Service Engine Soon light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly.) 2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securely tightened.
Instrumentation Transmission control indicator light (TCIL) (if equipped) The word OFF located on the end of the gearshift lever is the OVERDRIVE transmission control indicator light (TCIL). The TCIL may flash steadily if a malfunction is detected. If the TCIL is flashing, contact your Ford dealer as soon as possible. If this condition persists, damage to the transmission could occur.
Instrumentation Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster, check for a burned-out turn signal bulb. Refer to Exterior bulbs in the Maintenance and care chapter. High beams Illuminates when the high beam headlamps are turned on. Charging system Illuminates when the ignition is turned to the ON position and the engine is off.
Instrumentation Door ajar Illuminates when the ignition is in the ON or START position and any door is open. DOOR AJAR Oil pressure/Engine coolant This light will illuminate when the ignition is in the ON position and the: • engine coolant temperature is very high • engine oil pressure is low • engine is off The light serves as a notice that a system needs your attention and to check the engine coolant temperature gauge and the engine oil pressure gauge.
Instrumentation GAUGES F 50 40 FUEL FILL LOW FUEL 60 120 E 20 40 ! H - + 18 C 8 10 0 80 000000 140 L BRAKE 4 2 100 60 H 3 70 80 30 90 5 1 20 ABS 160 MPH 0 0 0 0 km/h P RN D 21 100 0 RPM X1000 SERVICE ENGINE SOON 6 DOOR AJAR LOW RANGE 4X4 Fuel gauge Displays approximately how much fuel is in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion.
Instrumentation Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool. Refer to Engine coolant in the Maintenance and care chapter. H C Never remove the coolant reservoir cap while the engine is running or hot.
Instrumentation Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control. 40 50 70 80 30 60 60 100 80 120 20 10 0 40 000000 140 90 20 160 MPH 0 0 0 0 km/h 100 Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer in the red zone may damage the engine. Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position.
Instrumentation Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains H in the normal range (the area between the “L” and “H”). If the gauge indicates low pressure, stop the vehicle as soon as safely L possible and switch off the engine immediately. Check the oil level. Add oil if needed (refer to Engine oil in the Maintenance and care chapter).
Instrumentation Mode control Each press of the MODE control will display a different feature as follows: Average fuel economy. The MODE E/M display will indicate the vehicle’s average fuel economy in liters/100 km (or miles/gallon) since the average fuel economy was last reset.
Instrumentation • if the vehicle is started while parked on an incline. • if less than 30 liters (8 gallons) of fuel is added to the fuel tank. The fuel range function will flash for 5 seconds at the following distances based on fuel remaining and fuel economy calculations: • 80 km (50 miles) • 40 km (25 miles) • 16 km (10 miles) Off. In this mode the display is off. Outside air temperature The temperature can be displayed in Centigrade or Fahrenheit by pressing the E/M control.
Instrumentation Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Locate the trip computer on the overhead console. 3. Turn ignition to the ON position. 1 15 2 14 3 13 4 12 11 5 6 10 7 8 9 4. Press and hold both trip computer controls. After approximately four seconds, the trip MODE E/M computer will enter zone setting mode. Zone setting mode is indicated when the display lights the “ZONE” indicator. 5.
Instrumentation Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Locate the trip computer located in the overhead console. 2. Start the vehicle. 3. Press and hold both trip computer controls. After approximately 8 seconds, the trip MODE E/M computer will enter CAL mode.
Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. P Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position and • the headlamp control is in the OFF or Parking lamps position. Always remember to turn on your headlamps at dusk or during inclement weather.
Controls and features Flash to pass Pull toward you to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full up position (past detent) to turn on interior lamps. 4WD CONTROL (IF EQUIPPED) This control operates the 4WD. Refer to the Driving chapter for more information.
Controls and features AUXILIARY POWER POINT The auxiliary power point is located on the instrument panel. Do not plug optional electrical accessories into the cigarette lighter. Use the power point. POWER POINT CLIMATE CONTROL SYSTEM Heater only system (if equipped) OFF Fan speed control Controls the volume of air circulated in the vehicle. Temperature control Controls the temperature of the airflow inside the vehicle. On heater-only systems, the air cannot be cooled below the outside temperature.
Controls and features • • • • • • (Panel) -Distributes outside air through the instrument panel registers. OFF-Outside air is shut out and the fan will not operate. (Panel and floor) -Distributes outside air through the instrument panel registers and the floor ducts. (Floor) -Allows for maximum heating. Distributes outside air through the floor ducts. (Floor and defrost) -Distributes outside air through the floor ducts and the windshield defroster ducts.
Controls and features Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or a sudden stop. Manual heating and air conditioning system (if equipped) OFF A/C MAX A/C Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Controls and features • MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster. Airflow will be from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle. • A/C-Uses outside air to cool the vehicle. It is quieter than MAX A/C but not as economical. Airflow will be from the instrument panel registers.
Controls and features Operating tips • In humid weather, select before driving. This will reduce your windshield from fogging. After a few minutes, select any desired position. • To prevent humidity buildup inside the vehicle, don’t drive with the climate control system in the OFF position. • Don’t put objects under the front seat that will interfere with the airflow to the back seats (if equipped). • Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield under the hood).
Controls and features USING YOUR AUDIO SYSTEM AM/FM Stereo VOL PUSH ON TONE TONE VOL ST SEEK DX FM 12 TUNE CLK 1 2 3 4 AM/FM AM/FM Stereo VOL PUSH ON TONE TONE VOL ST SEEK DX FM 12 TUNE CLK AM / FM STEREO 1 2 3 4 AM/FM 29
Controls and features Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. VOL PUSH ON VOL PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio mode. AM/FM AM/FM select in radio mode This control allows you to select AM or FM frequency bands.
Controls and features Tune adjust in radio mode • Press to move to the next SEEK frequency down the band (whether or not a listenable TUNE station is located there). Hold the control to move through the frequencies quickly. to move to the next frequency up the band (whether or not • Press a listenable station is located there). Hold for quick movement. Seek function The seek function control works in radio mode. Seek function in radio mode to find the next • Press listenable station down the frequency band.
Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. With the electronic AM/FM stereo, press the TONE control once, then use the volume knob to adjust the level. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. With the electronic AM/FM stereo, press the TONE control twice, then use the volume knob to adjust the level.
Controls and features Setting the clock Press CLK to toggle between listening frequencies and clock mode. To set the hour, press and hold the CLK control and press: • • TONE CLK to decrease hours and to increase hours. To set the minute, press and hold the CLK control and press: SEEK SEEK TUNE TUNE TONE CLK to decrease minutes and • SEEK SEEK to increase minutes. • TUNE TUNE The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.
Controls and features reverting back to the clock. In media mode, the media information will always be displayed. AM/FM stereo cassette VOL - PUSH ON AM FM1 BASS CLK ST TREB BAL FADE FM SEEK SCAN SIDE REW EJ TUNE 1 2 3 Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume.
Controls and features If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and tape modes. AM FM AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the AM control to select from AM selections, and press the FM control to select from FM1 or FM2 memory preset stations.
Controls and features Seek function in radio mode • Press to find the next listenable station down the frequency band. to find the next • Press listenable station up the frequency band. SEEK TUNE Scan function The scan function works in radio mode. SCAN Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode.
Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. BASS Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. TREB Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. BAL Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Controls and features Tape select • To enter tape mode while in radio mode, press the TAPE AMS control. CLK TAPE AMS Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection CLK being played or to skip to the next selection. TAPE To activate the feature, momentarily AMS depress the TAPE AMS button. Then, press either REW (for the beginning of the current selection) or FF (to advance to the next selection).
Controls and features Dolby姞 noise reduction Dolby威 noise reduction operates only in tape mode. Dolby威 reduces 4 the amount of hiss and static during tape playback. control to activate (and deactivate) Dolby威 noise reduction. Press the The noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Setting the clock Press CLK to toggle between listening frequencies and clock mode while in radio mode.
Controls and features • • to decrease minutes and to increase minutes. SEEK SEEK TUNE TUNE The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for ten seconds, when the radio is turned on, and then revert to clock information. Anytime that the media is changed, (new radio station, etc.
Controls and features Volume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control. Audio power is turned off by using the volume/power control. Turn control to raise or lower volume. VOL - PUSH ON VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Controls and features Tune adjust The tune control works in radio or CD changer mode. Tune adjust in radio mode to move to the next • Press frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. to move to the next • Press frequency up the band (whether or not a listenable station is located there). Hold for quick movement.
Controls and features Seek function in radio mode • Press to find the next listenable station down the frequency band. to find the next • Press listenable station up the frequency band. SEEK SEEK TUNE TUNE Seek function in tape mode to listen to the previous selection on the tape. • Press to listen to the next selection on the tape. • Press Seek function for CD or CD changer (if equipped) to seek to the previous • Press track of the current disc.
Controls and features Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.) To stop on a particular selection, press the control again. Scan function in CD or CD changer mode (if equipped) Press the SCAN control to hear a short sampling of all selections on the CD.
Controls and features Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations AUTO are filled, the station stored in memory preset control 1 will start playing. CLK If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Controls and features Press the TREB control then press: • to decrease the treble output and to increase the treble output. • SEL Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: to shift sound to the left and • to shift sound to the right. • Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Controls and features Tape/CD select • To begin tape play (with a tape loaded into the audio system) TAPE CD while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function. • To begin CD play (if CD(s) are loaded), press the CD control. TAPE CD The first track of the disc will begin playing. If returning from radio or tape mode, CD play will begin where it stopped last.
Controls and features Eject function Press the EJ control to stop and eject a tape. EJ Press the EJ control to stop and eject a CD. EJ Dolby noise reduction Dolby noise reduction reduces the amount of hiss and static during 4 tape playback. Press the control to activate (and deactivate) the noise reduction. Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
Controls and features Setting the clock To set the hour, press and hold the CLK control and press SEEK: AUTO CLK • • to decrease hours and to increase hours. SEEK SEEK TUNE TUNE To set the minute, press and hold the CLK control and press TUNE: AUTO CLK to decrease minutes and • to increase minutes. • If your vehicle has a separate clock module, (other than the digital radio display), the CLK button will not function in the above manner.
Controls and features The CLK button will allow you to switch between media display mode AUTO (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the media information will display for ten CLK seconds, when the radio is turned on, and then revert to clock information. Anytime that the media is changed, (new radio station, etc.), the media information will again display for ten seconds before reverting back to the clock.
Controls and features Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls which have a function for the specific mode of operation selected will be lit, while the controls which have no function for that mode will be turned off.
Controls and features AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play. AM/FM select in CD mode Press this control to stop CD play and begin radio play. Tune adjust The tune control works in radio or CD mode.
Controls and features Seek function in radio mode • Press to find the next listenable station down the frequency band. to find the next • Press listenable station up the frequency band. SEEK SEEK TUNE TUNE Seek function in tape mode to listen to the previous selection on the tape. • Press to listen to the next selection on the tape. • Press Seek function for CD changer (if equipped) to seek to the previous • Press track of the current disc.
Controls and features Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.) To stop on a particular selection, press the control again. Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD.
Controls and features Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. AUTO 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start RDS playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Controls and features Press the TREB control then press: • to decrease treble output and to increase treble output. • SEL Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: to shift sound to the left and • to shift sound to the right. • Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control then press: to shift sound to the front • and to shift sound to the rear.
Controls and features Tape/CD/CD changer (if equipped) select • To begin tape play (with a tape loaded into the audio system) TAPE CD while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function. • To begin CD play (if CD(s) are loaded), press the CD control. TAPE CD The first track of the disc will begin playing. After that CD play will begin where it stopped last.
Controls and features Tape direction select Press SIDE 1–2 to play the alternate side of a tape. Eject function Press the control to stop and eject a tape and/or a CD. SIDE 1-2 3 EJ Dolby noise reduction Dolby noise reduction reduces the amount of hiss and static during 4 tape playback. Press the control to activate (and deactivate) the noise reduction. Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
Controls and features Setting the clock Press the clock/RDS control until SELECT HOUR is displayed and press: AUTO RDS • • to decrease hours and to increase hours. To set the minute, press the clock/RDS control until SELECT MIN is displayed and press: SEL AUTO RDS • • to decrease minutes and to increase minutes.
Controls and features Radio Data System (RDS) feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations. Press and hold the control for three seconds to turn the feature on or off. Press the control to scroll through the following selections: RDS traffic announcement • Press the RDS control until TRAFFIC is displayed. AUTO RDS AUTO RDS • Use the SELECT control to select ON or OFF.
Controls and features RDS select program type • Press the RDS control until FIND program type is displayed. AUTO RDS • Use the SEL control to select the program type. With the feature on, use the SEEK or AUTOSET or SCAN control to find the desired program type from the following selections: • Classic • Country • Info • Jazz/R&B • Religious • Rock • Soft • Top 40 RDS show • With the RDS menu enabled, press the RDS control until SHOW is displayed.
Controls and features • Use the SEL control to select TYPE, NAME, TEXT or NONE. When your radio is turned to a RDS station, RDS station TYPE, station NAME, or TEXT message will be displayed along with the frequency. Press SEL in order to scroll through the text messages. Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. SEL EJ MUTE CD changer (if equipped) The CD changer is located behind the driver’s seat in your vehicle.
Controls and features Press to eject the magazine. Make sure only one disc is inserted in each slot. Each disc must be inserted with the label surface upward. Depending on your system, you may insert up to six or ten CDs. COMPACT DIGITAL AUDIO 6 5 4 3 6 COMPACT DISC MAGAZINE 2 1 The magazine does not need to be full for the changer to operate. Radio power must be turned on to play the CDs in the changer. The magazine may be stored in the glove compartment when not being used.
Controls and features Troubleshooting the CD changer (if equipped) The laser beam used in the compact disc player is harmful to the eyes. Do not attempt to disassemble the case. If sound skips: • You may be traveling on a rough road, playing badly scratched discs or the disc may be dirty. Skipping will not scratch the discs or damage the player. If your changer does not work, it may be that: • A disc is already loaded where you want to insert a disc. • The disc is inserted with the label surface downward.
Controls and features • Do not expose tapes to direct sunlight, high humidity, extreme heat or extreme cold. Allow tapes that may have been exposed to extreme temperatures to reach a moderate temperature before playing. • Tighten very loose tapes by inserting a finger or pencil into the hole and turning the hub. • Remove loose labels before inserting tapes. • Do not leave tapes in the cassette player for a long time when not being played.
Controls and features The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo. Audio system warranties and service Refer to the “Warranty Guide” for audio system warranty information. If service is necessary, see your dealer or a qualified technician. POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical 3 accessories such as the radio to 2 operate while the engine is not running. 2.
Controls and features SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). ON OFF Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on. To turn speed control off • Press OFF or • Turn off the vehicle ignition.
Controls and features To set a speed • Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). RES SET ACCEL COAST If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill.
Controls and features You can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed. To set a lower set speed • Press and hold CST/COAST. Release the control when the desired speed is reached or • Press and release CST/COAST. Each press will decrease the set speed by 1.6 km/h (1 mph) or RES SET ACCEL COAST • Depress the brake pedal.
Controls and features To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped) Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed.
Controls and features To return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). RES SET ACCEL COAST TILT STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving.
Controls and features HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals. Push the control on the end of the stalk to activate washer.
Controls and features FLASH TO PASS Pull toward you to activate and release to deactivate. OVERDRIVE CONTROL (IF EQUIPPED) Activating overdrive (Overdrive) is the normal drive position for the best fuel economy. The overdrive function allows automatic upshifts to second, third and fourth gear. Deactivating overdrive Press the Transmission Control Switch (TCS) located on the end of OVERDRIVE the gearshift lever.
Controls and features POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO • Press the bottom portion of the rocker switch to open. AUTO One touch down • Press AUTO completely down and release quickly. The driver’s window will open fully. Depress again to stop window operation.
Controls and features Window lock The window lock feature allows only the driver to operate the power windows. WINDOW LOCK To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls. Accessory delay (if equipped) With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened.
Controls and features 2. Move the control in the direction you wish to tilt the mirror. MIRRORS L R 3. Return to the center position to lock mirrors in place. Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features.
Controls and features REMOTE ENTRY SYSTEM (IF EQUIPPED) The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote entry features only operate with the ignition in the OFF position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting. Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate.
Controls and features Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Controls and features To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the transmitter unit. 3. Snap the two halves back together. Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s) or sound the personal alarm.
Controls and features Replacing lost transmitters Take all your vehicle’s transmitters to your dealer if service is required. If you purchase additional transmitters (up to four may be programmed), perform the following procedure: To reprogram the transmitters yourself, place the key in the ignition and turn from OFF to ON eight times in rapid succession (within 10 seconds) ending in ON. After doors lock/unlock, press any control on all transmitters (up to four). When completed, turn the ignition to OFF.
Controls and features TAILGATE LOCK (IF EQUIPPED) Your vehicle is equipped with a tailgate lock designed to prevent theft of the tailgate. • Insert ignition key and turn to the right to engage lock. • Turn ignition key to the left to unlock. Tailgate removal Your tailgate is removable to allow more room for loading. 1. Lower the tailgate. 2. Use a screwdriver to pry the spring clip (on each connector) past the head of the support screw. Disconnect cable. 3. Disconnect the other cable. 4.
Seating and safety restraints SEATING Full bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure that the seat is relatched into place. • Pull up on the release lever to quickly fold the seatback forward. 60/40 split bench seat (if equipped) • Lift the release bar to move the seat forward or backward. Ensure the seat is relatched into place. • Pull the seatback handle up to recline the seat.
Seating and safety restraints Captain’s chair (if equipped) • Lift the release bar to move the seat forward or rearward. Make sure that the seat is relatched into place. • Pull the seatback handle up to recline the seat. • Push the release lever down to quickly fold the seatback forward. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
Seating and safety restraints Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Using the manual lumbar support Turn the lumbar support control toward the front of vehicle to increase firmness. Turn the lumbar support control toward the rear of vehicle to increase softness.
Seating and safety restraints Rear folding bench seat (if equipped) Folding down the rear seats All safety belts should be properly stowed in the seat pockets before folding down the rear seat. Make sure that no objects such as books, purses or briefcases are on the floor in front of the second row seats before folding them down. 1. Locate the strap on the rear of the lower seat cushion. 2. Lift the strap and rotate the lower seat cushion toward the front of the vehicle. 3.
Seating and safety restraints 1. Lift/rotate the seatback toward the rear of the vehicle and make sure it latches securely. 2. Lift/rotate the lower seat cushion to its seating position. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To reduce the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving.
Seating and safety restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. To unfasten, push the release button and remove the tongue from the buckle.
Seating and safety restraints Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • When a tight lap/shoulder fit is desired. • Anytime a child safety seat is installed in a passenger front or outboard rear seating position (if equipped).
Seating and safety restraints • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
Seating and safety restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and fasten the belt when not in use.
Seating and safety restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... Then... The safety belt warning light illuminates for one to two minutes and the warning chime sounds for four to eight seconds. The safety belt warning light and warning chime turn off. The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding...
Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) 40 F H 50 60 60 70 80 30 3 VOL - PUSH ON 80 AM FM BASS TREB 1 40 140 20 10 0 2 100 120 20 H 18 90 FM1 ST BAL km/h 100 AUTO SET 4 SEEK RPM x 1000 SCAN TUNE EJ w DOLBY B NR TAPE CD DISCS P FADE DIESEL FUEL ONLY 160 MPH REW FF 1 SIDE 1-2 2 3 4 COMP SHUFFLE 5 6 PANEL DIM OFF O A/C MAX A/C Important supplemental restraint system (SRS) precautions The supplemental restraint system is designe
Seating and safety restraints Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries. Steps you can take to properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably. • Recline the seat slightly (one or two degrees) from the upright position. Do not put anything on or over the air bag module.
Seating and safety restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Air bags are designed to inflate in frontal and near-frontal collisions, not rollover, side-impact, or rear-impacts.
Seating and safety restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag is inflated, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Seating and safety restraints Disposal of air bags and air bag equipped vehicles (including pretensioners) For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. Passenger air bag ON/OFF switch (if equipped) An air bag ON/OFF switch has been installed in this vehicle.
Seating and safety restraints In order to avoid inadvertent activation of the switch, always remove the ignition key from the passenger air bag ON/OFF switch. Turning the passenger air bag back on The passenger air bag remains OFF until you turn it back ON. 1. Insert the ignition key and turn the switch to ON. PASSENGER AIRBAG 2. The OFF light will briefly OFF ON illuminate when the ignition is turned to On. This indicates that the OFF passenger air bag is operational.
Seating and safety restraints Always transport children who are 12 and younger in the rear seat. Always use safety belts and child restraints properly. If a child in a rear facing infant seat must be transported in front, the passenger air bag must be turned OFF. This is because the back of the infant seat is too close to the inflating air bag and the risk of a fatal injury to the infant when the air bag inflates is substantial.
Seating and safety restraints • although children ages 1 to 12 ride in the rear seat(s) whenever possible, children ages 1 to 12 sometimes must ride in the front because no space is available in the rear seat(s) of the vehicle; or • the child has a medical condition which, according to the child’s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’s condition. 3. Medical condition.
Seating and safety restraints 2.
Seating and safety restraints Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are four years old or younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children. Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle.
Seating and safety restraints A belt-positioning booster should be used if the shoulder belt rests in front of the child’s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion. You may wish to discuss the special needs of your child with your pediatrician.
Seating and safety restraints • Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling. • Place seat back in upright position. • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode (passenger side front and outboard rear seating positions)(if equipped). Ford recommends the use of a child safety seat having a top tether strap.
Seating and safety restraints Rear facing child seats should NEVER be placed in the front seats. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4.
Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with knee on the child seat. 8.
Seating and safety restraints Attaching safety seats with tether straps Some manufacturers make safety seats that include a tether strap that goes over the back of the vehicle seat and attaches to an anchoring point. Other manufacturers offer the tether strap as an accessory. Contact the manufacturer of your child safety seat for information about ordering a tether strap. Tether anchorage hardware A tethered seat can be installed in the front seat.
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter.
Starting 2. Make sure the headlamps and vehicle accessories are off. If starting a vehicle with an automatic transmission: • Make sure the parking brake is set. • If • • Make sure the gearshift is in P (Park). starting a vehicle with a manual transmission: Make sure the parking brake is set. Push the clutch pedal to the floor. 3. Turn the key to 4 (ON) without turning the key to 5 (START).
Starting F 50 40 FUEL FILL LOW FUEL 60 120 E 20 40 ! H - + 18 C 8 10 0 80 000000 140 L BRAKE 4 2 100 60 H 3 70 80 30 90 5 1 20 ABS 160 MPH 0 0 0 0 km/h P RN D 100 0 RPM X1000 SERVICE ENGINE SOON 21 6 DOOR AJAR LOW RANGE 4X4 Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. light may not illuminate. • If the driver’s safety belt is fastened, the STARTING THE ENGINE 1.
Starting Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below. For best results, plug the heater in at least three hours before starting the vehicle.
Starting Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air.
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Driving Using RABS • In an emergency, applying full pressure may cause the front wheels to lock. If the front brakes lock, the vehicle cannot be steered. You should apply the brakes with steadily increasing force, as if “squeezing” the brakes. If you feel the front wheels begin to lock, momentarily release the pedal and repeat the “squeeze” technique. • We recommend that you familiarize yourself with how the RABS performs. However, avoid unnecessary risks.
Driving With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with parking brake released. (If your brake warning lamp illuminates, have your vehicle serviced immediately). Using ABS • In an emergency or when maximum efficiency from the ABS is required, apply continuous full force on the brake.
Driving Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency. Since the parking brake applies only the rear brakes, the vehicle’s stopping distance will increase greatly and the handling of your vehicle will be adversely affected.
Driving Extended use of other than the manufacturer’s specified size tires on a Traction-Lok rear axle could result in a permanent reduction in effectiveness. This loss of effectiveness does not affect normal driving and should not be noticeable to the driver. To avoid injury, never run the engine with one wheel off the ground, such as when changing a tire.
Driving Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn off the ignition whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician. Driving with a 4–speed automatic transmission Understanding gearshift positions Pull the gearshift lever towards you and downward to move the automatic gearshift.
Driving N (Neutral) With the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through four. (Overdrive) can be deactivated by pressing the Transmission Control Switch (TCS) on the end of the gearshift lever. The transmission control indicator light (TCIL) (the word OFF) on the end of the gearshift lever will illuminate.
Driving 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear, and will shift to 1 (Low) after vehicle decelerates to the proper speed.
Driving 4. Turn ignition to position 5 (START) to start the engine, let the engine idle for a few seconds, then shift into gear. 5. Release the brake pedal. 6. Release clutch slowly while pressing down slowly on the accelerator pedal. 4 3 5 2 1 • Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standstill while waiting on a hill. These actions will seriously reduce clutch life.
Driving 1 2 Maximum downshift speeds 1 6-speed transmission Shift from: Transfer case position (if equipped)2 2H or 4H 4L D (Overdrive) - 4 72 km/h (45 mph) 26 km/h (16 mph) 4-3 56 km/h (35 mph) 19 km/h (12 mph) 3-2 32 km/h (20 mph) 13 km/h (8 mph) 2-1 8 km/h (5 mph) 3 km/h (2 mph) 1 - LO Only shift to LO when at a stop. Use 2H or 4H for 4WD equipped vehicles. Downshift at lower speeds when driving on slippery surfaces. Parking your vehicle 1. Disengage the clutch, apply brake and shift into N (Neutral).
Driving 2. Set parking brake. 3. Shift into 1 (First). 4. Turn the ignition key to position 3 (OFF). 4 3 5 2 1 Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully. Reverse Make sure that your vehicle is at a complete stop before you shift into R (Reverse). Failure to do so may damage the transmission. Put the gearshift in N (Neutral) and wait at least three seconds before shifting into R (Reverse).
Driving With the 5-speed transmission you can shift into R (Reverse) only by moving the gearshift from left of 3 (Third) and 4 (Fourth) gears before you shift into R (Reverse). This is a special lockout feature that protects you from accidentally shifting into R (Reverse) when you downshift from D (Overdrive). With the 6-speed transmission you can shift into R (Reverse) by moving the gearshift left from N (Neutral).
Driving Removing key from ignition • Turn the ignition key until it stops. • Push the release lever forward and rotate the key towards you and remove. POWER TAKE OFF (PTO) CAPABILITY (IF EQUIPPED) Some vehicles with 6.8L and 7.3L engines are equipped with Power Take Off (PTO) capability. These vehicles have a special transmission case, internal components and calibration for PTO usage. If your vehicle is equipped with a 7.3L Diesel engine, refer to the 7.
Driving FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) When Four–wheel drive (4WD) is engaged, power is supplied to all four wheels through a transfer case. 4WD power can be selected when additional driving power is desired. If equipped with the Electronic Shift 4WD System, and the instrument panel control is moved to 4WD Low while the vehicle is moving, the system will not engage and no damage will occur to the 4WD system.
Driving • automatic hub locks can be manually overridden by rotating the hub lock control from AUTO to LOCK. Manual 4x4 system (if equipped) The 4WD system is engaged or disengaged by rotating the front wheel hub lock control from FREE to LOCK, then manually engaging the transfer case with a floor-mounted shifter. 4WD system indicator lights The 4WD system indicator lights illuminate only under the following conditions. If these lights illuminate during normal driving, have your vehicle serviced.
Driving Shifting from 2H (2WD high) to 4H (4WD high) Engage the locking hubs by rotating the hub lock control from FREE to LOCK, then move the transfer case lever from 2H (2WD High) to 4H (4WD High). Do not shift into 4H (4WD High) with the rear wheels slipping. 2H 4H N 4L Shifting from 4H (4WD high) to 2H (2WD high) Move the transfer case lever to 2H 2H (2WD High) at a stop or any forward speed up to 88 km/h (55 4H mph).
Driving 4. Move the transfer case shift lever through N (Neutral) directly to 4H (4WD High) or 4L (4WD Low). 2H 4H N 4L Using the N (Neutral) position The transfer case neutral position overrides the transmission and puts the vehicle in neutral regardless of transmission gearshift lever position. The vehicle can move forward or backwards. This position should only be used 2H when towing the vehicle. Refer to Wrecker towing in the Roadside 4H emergencies chapter.
Driving Shifting from 2WD (2WD high) to 4x4 HIGH (4WD high) Rotate the 4WD control to the 4x4 HIGH position at speeds up to 88 4X4 4X4 HIGH km/h (55 mph). LOW 2WD • Do not shift into 4x4 HIGH with the rear wheels slipping. Shifting from 4x4 HIGH (4WD high) to 2WD (2WD high) Rotate the 4WD control to 2WD at 4X4 any forward speed. You do not need 4X4 HIGH LOW 2WD to put the gearshift in R (Reverse) to disengage your front hubs.
Driving 4. Move the 4WD control to the 4x4 HIGH or 4x4 LOW position. 2WD 4X4 HIGH 4X4 LOW Driving off-road with 4WD Your vehicle is specially equipped for driving on sand, snow, mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in rough terrain.
Driving Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels. Mud and water If you must drive through high water, drive slowly. Traction or brake capability may be limited. When driving through water, determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly.
Driving If vehicle speed drops more than 16 km/h (10 mph), the speed control will cancel automatically. Resume speed with accelerator pedal. If speed control cancels after climbing the hill, reset speed by pressing and holding the SET ACCEL button to resume speeds over 50 km/h (30 mph). Automatic transmissions may shift frequently while driving up steep (Overdrive) into grades. Eliminate frequent shifting by shifting out of a lower gear.
Driving • GVWR (Gross Vehicle Weight Rating) : Maximum total weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver’s door pillar. • GAWR (Gross Axle Weight Rating) : Carrying capacity for each axle system. The GAWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver’s door pillar.
Driving weight to the front of your vehicle, (potentially including weight added to the cab), the weight added should not exceed the Front Axle Reserve Capacity (FARC). Additional frontal weight may be added to the front axle reserve capacity provided you limit your payload in other ways (i.e. restrict the number of passengers or amount of cargo carried). You may add equipment throughout your vehicle if the total weight added is equal to or less than the Total Axle Reserve Capacity (TARC) weight.
Driving Driving through deep water where the transmission is submerged may allow water into the transmission and cause internal transmission damage. TOWING A TRAILER Your vehicle may tow a Conventional/Class IV trailer or fifth wheel trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your engine and rear axle ratio on the following charts. 2nd unit bodies are not included in maximum trailer weight ratings.
Driving Trailer towing tables Engine 5.4L 5.4L 6.8L 6.8L F-250 Rear axle ratio 3.73 4.10 3.73 4.30 with manual transmission Maximum GCWR-kg Maximum trailer (lbs.) weight-kg (lbs.) 1 6 124 (13 500) 4 536 (10 000) 6 804 (15 000) 4 536 (10 000) 7 484 (16 500) 4 536 (10 000) 8 165 (18 000) 4 536 (10 000) 1 Conventional/Class IV trailer hitch only. Fifth wheel trailer maximum weights can be calculated by subtracting GVW from GCWR. Engine 5.4L 5.4L 6.8L 6.
Driving Engine 5.4L 5.4L 6.8L 6.8L F-350 with automatic transmission Rear axle Maximum GCWR-kg Maximum trailer ratio (lbs.) weight-kg (lbs.) 1 3.73 6 124 (13 500) 4 536 (10 000) 4.10 6 804 (15 000) 4 536 (10 000) 3.73 7 711 (17 000) 4 536 (10 000) 4.30 9 072 (20 000) 4 536 (10 000) 1 Conventional/Class IV trailer hitch only. Fifth wheel trailer maximum weights can be calculated by subtracting GVW from GCWR. Engine 6.8L 6.
Driving Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle’s bumper or attach to the axle. You must distribute the load in your trailer so that 10% of the total weight of the trailer is on the tongue.
Driving Trailer brakes Electric brakes and manual, automatic or surge-type brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. The braking system of the tow vehicle is rated for operation at the GVWR not GCWR.
Driving Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your Scheduled Maintenance guide for more information. Trailer towing tips • Practice turning, stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached.
Driving • 4x2 vehicles must have the driveshaft removed if the rear wheels are to be kept on the ground. If only the front wheels will be on the ground, the driveshaft does not need to be removed. • 4x4 Electronic Shift on the Fly vehicles cannot be towed with any wheels on the ground. • 4x4 vehicles with a manual shift (floor-mounted) transfer case shifter must have the transfer case and transmission gearshift levers placed in the N (Neutral) position in order to tow with all wheels on the ground.
Driving • After installing a snowplow to the vehicle, ensure the vehicle’s front toe alignment and front ride height are within specification (reset if required). These specifications are located in the vehicle’s Workshop Manual. Adherence to the toe, tire pressures and ride height specification is important for proper tire wear, ride, handling and headlight aim. Also, maintain the engine oil and transmission fluid change intervals following the severe duty schedule.
Driving Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Engine temperature while plowing When driving with a plow, your engine may run at a higher temperature than normal because the attached snowplow blade will restrict airflow to the radiator.
Roadside emergencies HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously. • Depress control again to turn the flashers off.
Roadside emergencies Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds and return the key to the OFF position. 5. Make a further check for leaks in the fuel system.
Roadside emergencies Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses 2A 3A 4A 5A 7.
Roadside emergencies 20 21 10 11 RELAY 5 9 31 30 29 19 8 RELAY 4 28 18 7 27 17 6 26 16 25 15 4 5 RELAY 3 24 14 2 3 23 13 12 FUSE1 RELAY 1 (NOT USED) 22 To remove a fuse use the fuse puller tool provided on the fuse panel cover. The fuses are coded as follows.
Roadside emergencies Fuse/Relay Location 8 9 10 11 Fuse Amp Rating 5A — — 10A 12 13 15A 20A 14 15 10A 5A 16 17 18 19 15A — — 10A 20 15A 21 22 — 10A 23 24 10A 10A 25 5A 26 — 148 Description Radio, Headlamp Switch Illumination Not Used Not Used Washer Pump, Wiper Run/Park Relay Coil, Wiper Hi/LO Relay Coil, Washer Pump Relay Coil Horn Stop Lamps, Center High-mount Stop Lamp, Trailer Tow Stop Lamp Dome Lamp, Cargo Lamp, Courtesy Lamps Generic Electronic Module (GEM), Powertrain Control Modul
Roadside emergencies Fuse/Relay Location 27 28 29 30 31 Relay Relay Relay Relay Relay 1 2 3 4 5 Fuse Amp Description Rating 10A Ignition Run Power Feed (Customer Access) 10A Brake Shift Interlock, DRL Relay Coil, Speed Control Module, Backup Lamps, Trailer Tow Backup Lamp Relay Coil, Electronic Shift On The Fly Hub Lock Solenoid 5A Instrument Cluster (Charge and Airbag Warning Lamps) 30A PCM Relay Coil, Ignition Coil (Gasoline only), Fuel Heater (Diesel only), Wastegate Solenoid (Diesel only), Injector
4 2 3 1 20 6 5 21 8 7 22 10 24 14 9 25 15 12 26 16 11 27 17 23 28 18 13 29 19 36 35 34 33 32 31 30 37 Roadside emergencies The high-current fuses and relays are coded as follows. Fuse/Relay Location 1 2 3 4 5 6 150 Fuse Amp Rating 7.5A * 10A* 7.
Roadside emergencies Fuse/Relay Location 7 8 Fuse Amp Rating 20A* (Gasoline only) 5A* (Diesel only) 15A* 9 10 11 12 13 14 15 16 17 10A* 25A* 10A* 10A* 30A** 60A** 30A** 30A** 30A** 18 19 20 21 22 23 24 25 26 30A** 20A** 50A** 50A** 50A** 40A** 30A** 30A*** 20A** Description Gasoline only-Vapor Managment Valve, HEGO Sensors, Intake Manifold Communication Control, EVR Solenoid, PCM, Canister Vent Solenoid Diesel only-Dual Alternator ⬙A⬙ Field Trailer Tow Electronic Brake Illumination, Park Lamps, Trail
Roadside emergencies Fuse/Relay Location 27 28 29 30 31 32 Fuse Amp Rating (Gasoline only) 30A* (Diesel only) 30A** 20A** ---- Description Gasoline only-Not Used Diesel only-Injector Driver Module Trailer Tow Electronic Brake Controller Radio PCM Power Relay Blower Motor Relay Two Speed Fuel Pump Relay (Gasoline only), Injector Driver Module Power Relay (Diesel only) 33 -Washer Pump Relay 34 -Windshield Wiper Park/Run Relay 35 -Windshield Wiper HI/LO Relay 36 -Not Used 37 -PCM Relay Diode 38 -Trailer To
Roadside emergencies If your vehicle is equipped with 4WD, a spare tire of a different size than the road tires should not be used. Such a tire could result in damage to driveline components and make the vehicle difficult to control.
Roadside emergencies 2. The following steps are required to move the support bracket (if equipped) away from the spare tire: • With tapered end of lug wrench, loosen the eyebolt on the support bracket. • Line up the eyebolt with the slot in the support bracket. • Slide the support bracket off the eyebolt and move the support bracket away from the spare tire. 3. Insert the hooked end of the jack handle into the rear bumper opening.
Roadside emergencies 5. The following steps are required to secure the support bracket (if equipped) under the spare tire: • Move the support bracket over the spare tire. • Slide the support bracket over the eyebolt into the slot on the support bracket. • Tighten the eyebolt with tapered end of lug wrench leaving it positioned at a right angle of the slot on the support bracket. Tire change procedure 1. Park on a level surface, activate hazard flashers and set the parking brake.
Roadside emergencies 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park) (automatic transmission) or R (Reverse) (manual transmission).
Roadside emergencies • Front (4x2) • Front passenger side (4x4) 157
Roadside emergencies • Front driver side (4x4) Make sure the jack fits into the notched area on the differential housing.
Roadside emergencies 8. Turn the jack handle clockwise until the wheel is completely off the ground and high enough to install the spare tire. 9. Remove the lug nuts with the lug wrench. 10. On single rear wheel vehicles, replace the flat tire with the spare tire, making sure the valve stem is facing outward for all front tires and vehicles equipped with single rear wheels. If replacing an inboard rear tire on a dual rear wheel vehicle, the valve stem must be facing outward.
Roadside emergencies • Front (4x2) • Front driver side (4x4) • Front passenger side (4x4) 160
Roadside emergencies • Rear 14. Insert the jack handle into the pump linkage. 15. Use an up-and-down motion with the jack handle to raise the wheel completely off the ground. Hydraulic jacks are equipped with a pressure release valve that prevents lifting loads which exceed the jack’s rated capacity. 16. Remove the lug nuts with the lug wrench. 17. Replace the flat tire with the spare tire, making sure the valve stem is facing outward on all front an inboard rear wheels.
Roadside emergencies The following steps apply to all vehicles: 19. Remove the jack and fully tighten 1 the lug nuts in the order shown. 6 7 20. Stow the flat tire. Refer to Stowing the spare if the vehicle is equipped with a spare tire carrier. 4 3 21. Stow the jack, jack handle and lug wrench. Make sure the jack is securely fastened so it does not 8 5 rattle when driving. 2 22. Unblock the wheels.
Roadside emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted. Do not attempt to push start your vehicle. Automatic transmissions do not have push-start capability. Preparing your vehicle 1.
Roadside emergencies Connecting the jumper cables + + – – 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Roadside emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. The preferred locations of an exposed metal part (to ground the circuit) are the alternator mounting brackets or an engine lifting eye.
Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. + + – – 2.
Roadside emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground using a wheel lift or a slingbelt with T-hooks. On 4x4 vehicles, it is recommended that your vehicle be towed with a wheel lift or flatbed equipment with all the wheels off the ground.
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a Scheduled Maintenance Guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your “Warranty Guide” to find out which parts and services are covered.
Maintenance and care Working with the engine off • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. • Manual transmission: 1. Set the parking brake. 2. Depress the clutch and place the gearshift in 1 (First). 3. Turn off the engine and remove the key. 4. Block the wheels to prevent the vehicle from moving unexpectedly.
Maintenance and care OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch located under the right center of the hood. Slide the handle to release the auxiliary latch. 3. Lift the hood until the lift cylinders hold it open.
Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 9 8 10 11 1 2 7 3 4 5 6 1. Engine oil dipstick 2. Clutch fluid reservoir (manual transmission) 3. Brake fluid reservoir 4. Power distribution box 5. Power steering fluid reservoir 6. Air filter assembly 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9. Battery 10. Engine oil filler cap 11.
Maintenance and care 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmission) or 1 (First) (manual transmission). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). MIN MAX 6. Wipe the indicator clean. Insert the indicator fully, then remove it again.
Maintenance and care Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the MIN and MAX ranges, add only certified engine oil of the recommended viscosity. Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the MAX mark on the engine oil level indicator (dipstick). 4.
Maintenance and care Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application.
Maintenance and care 2. Visually inspect the fluid level. 3. If necessary, add brake fluid until the level reaches MAX. Do not fill MAX above this line. 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter. Brake fluid is toxic. If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail.
Maintenance and care 1. Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir. 2. Remove cap and rubber diaphragm from reservoir. 3. Add fluid until the level reaches the step in the reservoir. 4. Reinstall rubber diaphragm and cap onto reservoir. WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is symbol. highlighted with a If the level is low, add enough fluid to fill the reservoir.
Maintenance and care ENGINE COOLANT Check the level of the engine coolant in the reservoir. Refer to the Scheduled Maintenance Guide for service interval schedules. Be sure to read and understand Precautions when servicing your vehicle in this chapter. MAX COLD FILL RANGE MIN If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become empty. If this occurs, add engine coolant to the reservoir.
Maintenance and care • DO NOT MIX recycled coolant and conventional coolant together in your vehicle. Mixing of engine coolants may harm your engine’s cooling system. • The use of an improper coolant may harm engine and cooling system components and may void the warranty of your vehicle’s engine cooling system. • Use only the type of coolant with which your vehicle was originally equipped. If you are unsure which type of coolant your vehicle requires, contact your local dealer.
Maintenance and care Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44–A, and use of such coolant may harm engine and cooling system components. Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.
Maintenance and care How fail-safe cooling works If the engine begins to overheat: • the engine coolant temperature H gauge will move to the red (hot) area. symbol will illuminate. • the symbol will illuminate. • the C • the Service Engine Soon indicator light will illuminate. If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine.
Maintenance and care Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to a service facility as soon as possible. CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the “Service Guide” for the service interval schedules. If adding fluid is necessary, use only MERCON威 ATF. 1.
Maintenance and care operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature. 2. Park the vehicle on a level surface and engage the parking brake. 3.
Maintenance and care The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition.
Maintenance and care Checking and adding manual transmission fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.
Maintenance and care Checking and adding transfer case fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication.
Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules. Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells.
Maintenance and care When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution.
Maintenance and care RN LE TU AD RE • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. RECYCLE WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades.
Maintenance and care INFORMATION ABOUT TIRE QUALITY GRADES New vehicles are fitted with tires that have their Tire Quality Grade (described below) molded into the tire’s sidewall. These Tire Quality Grades are determined by standards that the United States Department of Transportation has set. Tire Quality Grades apply to new pneumatic tires for use on passenger cars.
Maintenance and care Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Maintenance and care • Four tire rotation • Five tire rotation 192
Maintenance and care Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the label. If you do not follow these precautions, your vehicle may not drive properly and safely.
Maintenance and care The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains. If you need to use chains, it is recommended that steel wheels (of the same size and specifications) be used as chains may chip aluminum wheels. Follow these guidelines when using snow tires and chains: • Use only SAE Class S chains.
Maintenance and care Automotive fuels can cause serious injury or death if misused or mishandled. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury.
Maintenance and care When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container.
Maintenance and care with the recommended octane rating, see your dealer or a qualified service technician to prevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular” unleaded gasoline. “Premium” unleaded gasoline is not recommended (particularly in the United States) because it may cause these problems to become more pronounced.
Maintenance and care 4. To install the cap, align the tabs on the cap with the notches on the filler pipe. 5. Turn the filler cap clockwise 1/8 of a turn until it stops. If the “Service Engine Soon/Check Engine” indicator comes on and stays on when you start the engine, the fuel filler cap may not be properly installed. Turn off the engine, remove the fuel filler cap, align the cap properly and reinstall it.
Maintenance and care driving (engine break-in period). You will get a more accurate measurement after 3 000 km–5 000 km (2 000 miles-3 000 miles). Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill Capacities chart in this “Owner Guide.” The advertised capacity is the amount of the Indicated Capacity and the Empty Reserve combined.
Maintenance and care 5. Follow one of the simple calculations in order to determine fuel economy: Multiply liters used by 100, then divide by total kilometers traveled. Divide total miles traveled by total gallons used. Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’s fuel economy under current driving conditions. Additionally, keeping records during summer and winter will show how temperature impacts fuel economy.
Maintenance and care • Resting your foot on the brake pedal while driving may reduce fuel economy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy. • Use recommended engine oil. Refer to Lubricant Specifications. • Perform all regularly scheduled maintenance items.
Maintenance and care It is important to note the box in the lower left corner of the window sticker. These numbers represent the Range of Km/L (MPG) expected on the vehicle under optimum conditions. Your fuel economy may vary depending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards.
Maintenance and care sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine. This decal identifies engine displacement and gives some tune up specifications. Please consult your “Warranty Guide” for complete emission warranty information.
Maintenance and care • Tail lamps • Back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance. Replacing headlamp bulbs (aerodynamic) Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass.
Maintenance and care Replacing headlamp bulbs (sealed beam) To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position. 2. Open the hood. 3. Remove the two screws and parking lamp/side marker assembly by pulling gently 4. Disconnect the electrical connectors from the parking lamp/side marker assembly and remove. 5. Remove the four bolts and headlamp bezel. 6. Remove the four screws and the headlamp retaining ring from headlamp. 7. Disconnect the electrical connector and remove headlamp.
Maintenance and care Replacing tail lamp/Backup lamp bulbs The tail lamp/backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies. 2. Remove the two screws from the tail lamp assembly. 3. Carefully pull the lamp assembly from the tailgate pillar by releasing the two retaining tabs. 4. Twist the bulb socket 1⁄4 turn counterclockwise and remove from lamp assembly. 5.
Maintenance and care To install the brakelamp assembly: 1. Install the bulb into the lamp assembly and rotate clockwise. 2. Install the lamp assembly on the vehicle with two screws. Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper. To change the license plate lamp bulbs: 1. Reach behind the rear bumper to locate the bulb. 2. Twist the bulb socket counterclockwise 1⁄4 turn and carefully pull to remove it from the lamp assembly. 3.
Maintenance and care AIMING THE HEADLAMPS The alignment of your headlamps should be checked by a qualified service technician if: • Oncoming motorists frequently signal you to deactivate your high beams, and your high beams are not activated. • The headlamps do not seem to provide enough light for clear night vision. • The headlamp beams are pointed substantially away from a slightly down and to the right position.
Maintenance and care Waxing your vehicle Wax when water stops beading on the surface. This could be every three or four months, depending on operating conditions. Use only carnauba or synthetic-based waxes. Use cleaning fluid or alcohol with a clean cloth to remove any bugs before waxing vehicle. Use tar remover to remove any tar spots. Avoid getting wax on the windshield.
Maintenance and care Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. Use glass cleaner or tar remover if necessary. To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners.
Maintenance and care Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, wear or cuts. If your vehicle has been involved in an accident, refer to the Safety belt maintenance section in the Seating and safety restraints chapter.
Capacities and specifications MOTORCRAFT PART NUMBERS Component* Air filter element Fuel filter Oil filter PCV valve Battery (Standard) Battery (Optional) Spark plugs-platinum** 5.4L V8 engine FA-1634 FG-986B FL-820-S EV-233 BXT-65-650 BXT-65-750 AWSF-22E 6.8L V10 engine FA-1634 FG-986B FL-820-S EV-233 BXT-65-650 BXT-65-650 AWSF-22E *Refer to the 7.3 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for Motorcraft diesel engine service part numbers.
Capacities and specifications Fluid Engine coolant5 Ford Part Name Premium Engine Coolant Application 5.4L V8 engine without A/C 5.4L V8 engine with A/C 6.8L V10 engine Engine oil (includes filter change)Gas engines Engine oil (includes filter change)Diesel engine Fuel tank Motorcraft 5W-30 Super Premium Motor Oil All Power steering fluid Transfer case fluid Capacity 16.9L (17.9 quarts) 18.4L (19.4 quarts) 29.0L (30.6 quarts) 5.7L (6.0 quarts) Refer to your 7.
Capacities and specifications Fluid Ford Part Name Transmission Synthetic fluid3 MERCON威 ATF Motorcraft MERCON威 ATF Windshield washer fluid 1 Ultra-Clear Windshield Washer Concentrate Application 5-speed manual 6-speed manual Capacity 3.2L (3.4 quarts) 5.5L (5.8 quarts) 16.1L (17.1 quarts)4 Automatic 4R100 with small cooler (vehicles equipped with 20 oil-to-airplate cooler) Automatic 16.7L 4R100 with large (17.7 quarts)4 cooler (vehicles equipped with 26 oil-to-airplate cooler) All 4.0L (4.
Capacities and specifications LUBRICANT SPECIFICATIONS Item Front axle (4X4) Rear axle Brake fluid and clutch fluid (if equipped) Engine coolant Engine oil Ford part name or equivalent Motorcraft SAE 75W90 Axle Lubricant Motorcraft SAE 75W140 High Performance Synthetic Rear Axle Lube1 Motorcraft SAE 75W90 Synthetic Rear Axle Lube1 (Dana 80 axles) Motorcraft SAE 80W90 Premium Rear Axle Lubricant1 (Dana 135 axles) High Performance DOT 3 Motor Vehicle Brake Fluid Ford Premium Engine Coolant Motorcraft 5W-
Capacities and specifications Item Hinges, latches, striker plates, fuel filler door hinge and seat tracks Transmission /steering/parking brake linkages and pivots, brake and clutch pedal shaft (if equipped) Power steering fluid and transfer case fluid (if equipped) Manual transmission (5-speed) Manual transmission (6-speed) Automatic transmission Windshield washer fluid 1 Ford part name or equivalent Multi-Purpose Grease Ford part number Ford specification DOAZ-19584-AA ESB-M1C93-A or F5AZor 19G209-AA
Capacities and specifications ENGINE DATA Engine Cubic inches Horsepower Torque Required fuel Firing order Spark plug gap Ignition system Compression ratio 5.4L V8 engine 330 235 @ 4250 rpm 335 lb.-ft. @ 3000 rpm 87 octane 1-3-7-2-6-5-4-8 1.3-1.4 mm (0.052-0.056 inch) Coil on plug 9.0:1 6.8L V10 engine 415 275 @ 4250 rpm 410 lb.-ft. @ 2650 rpm 87 octane 1-6-5-10-2-7-3-8-4-9 1.3-1.4 mm (0.052-0.056 inch) Coil on plug 9.
Capacities and specifications F250-Crew cab Dimension (1) Overall height (2) Track (Front / Rear) (3) Overall width (4) Wheelbase (5) Overall length a b 1 1 1 1 1 3 4 6 6 Body Crew Cab 4x2 960 mm (77.2 in)a / 883 mm (74.1 in)b 745 mm (68.7 in)/ 729 mm (68.1 in)a,b 988 mm (78.3 in)a,b 967 mm (156.2 in )a / 379 mm (172.4 in)b 242 mm (245.8 in)a / 654 mm (262.0 in)b style Crew Cab 4x4 2 053mm (80.8 in)a / 2 052 mm (80.8 in)b 1 736 mm (68.4 in)/ 1 729 mm (68.1 in)a,b 1 988 mm (78.3 in)a,b 3 967 mm (156.
Capacities and specifications (5) Overall length 5 732 mm (225.7 in) 5 754 mm (226.5 in) 5 879 mm (231.4 in)a / 6 288 mm (247.6 in)b 6 291 mm (247.7 in) a Short wheel base Long wheel base c Single rear wheels d Dual rear wheels b F350-Crew cab Dimension (1) Overall height (2) Track (Front / Rear) (3) Overall width (4) Wheelbase (5) Overall length a b 1 1 1 1 3 4 6 6 Body Crew Cab 4x2 929 mm (75.9 in) 745 mm (68.7 in)/ 729 mm (68.1 in)a,b 988 mm (78.3 in)a,b 967 mm (156.2 in )a / 379 mm (172.
Capacities and specifications (4) Wheelbase (5) Overall length 3 576 mm (140.8 in) 5 732 mm (225.7 in)a 6 341 mm (249.6 in)b a Short wheel base b Long wheel base 4 186 mm (164.8 in) - 4 475 mm (176.2 in) - 4 475 mm (176.2 in) - Body Chassis Cab 4x4 2 075 mm (81.6 in) 1 736 mm (68.3 in) / 1 879 mm (74 in) 2 376 mm (93.5 in) 3 576 mm (140.8 in) - style Crew Cab 4x2 2 067 mm (81.4 in) 1 736 mm (68.4 in) / 1 610 mm (63.4 in) 2 376 mm (93.5 in) 4 475 mm (176.2 in) - Crew Cab 4x4 2 066 mm (81.
Capacities and specifications 1 2 3 4 5 221
Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side. MFD. BY FORD MOTOR CO. IN U.S.A.
Customer assistance GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.
Customer assistance Ford extended service plan You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada).
Customer assistance Getting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. When you need warranty repairs your selling dealer would like you to return to it for that service, but you may also take your vehicle to another Ford Motor Company dealership authorized for warranty repairs. Certain warranty repairs require special training though, so not all dealers are authorized to perform all warranty repairs.
Customer assistance Please have the following information available when contacting Ford Customer Assistance: • Your telephone number (home and business) • The name of the dealer and the city where the dealership is located • The year and make of your vehicle • The date of vehicle purchase • The current odometer reading • The vehicle identification number (VIN) If you still have a complaint involving a warranty dispute, you may wish to contact the Dispute Settlement Board (U.S.
Customer assistance • sales disputes between customer and dealer except those associated with warranty repairs or concerns with the vehicle’s performance as designed • a request for reimbursement of consequential expenses unless a service or product concern being reviewed • items not covered by the New Vehicle Limited Warranty (including maintenance and wear items) • alleged personal injury/property damage claims • cases currently in litigation • vehicles not used primarily for family, personal or household
Customer assistance Your dealership and a Ford Motor Company representative are asked to submit statements at this time.
Customer assistance the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law. To Request a DSB Brochure/Application For a brochure/application, speak to your dealer or write/call to the Board at the following address/phone number: Dispute Settlement Board P.O.
Customer assistance FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. Telephone: (313) 594-4857 FAX: (313) 390-0804 If you are in another foreign country, contact the nearest Ford dealership. If the dealership employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S.
Customer assistance A wide selection of accessories is available through your local authorized Ford, Lincoln-Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle. In addition, each accessory is made from high quality materials and meets or exceeds Ford’s rigid engineering and safety specifications.
Customer assistance Travel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adaptors Fog lights Framed luggage covers Heavy-duty battery Neutral towing transfer case kit (Explorer 4.
Customer assistance Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front end covers (full and mini) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl floor mats Rallye bars Rear air deflectors Rear decklid spoilers Side window air deflectors Spare tire lock Step bumpers Step/sill plates Tailgate covers Tailgate lock Tailgate protector Tonneau covers Touch-up paint Universal floor mats For maximum vehicle performance, keep the following information in mi
Customer assistance • The Federal Communications Commission (FCC) and Canadian Radio Telecommunications Commission (CRTC) regulate the use of mobile communications systems - such as two-way radios, telephones and theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician.
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Index Accessory delay ..........................75 Air bag supplemental restraint system ..........................92 and child safety seats ..............93 description ................................92 disposal ......................................96 driver air bag ............................94 indicator light ......................10,95 operation ...................................94 passenger air bag .....................94 passenger deactivation switch ...96 Air cleaner filter ......................
Index Ford Extended Service Plan ...224 Getting assistance outside the U.S. and Canada .....................229 Getting roadside assistance ...223 Getting the service you need ...225 Ordering additional owner’s literature .................................234 The Dispute Settlement Board ...226 Dipstick engine oil .................................172 Doors door ajar warning .....................13 Driveline universal joint and slip yoke ....................................
Index GAWR (Gross Axle Weight Rating) .....132 calculating ...............................134 definition .................................132 driving with a heavy load ......132 location ....................................132 GVWR (Gross Vehicle Weight Rating) ..........................132 calculating ........................132,134 definition .................................132 driving with a heavy load ......132 location ....................................132 Hazard flashers .........................
Index Parking brake ............................114 Parts (see Motorcraft parts) ....212 Power distribution box (see Fuses) ........................................149 Power door locks ........................75 Power steering ..........................115 fluid, checking and adding ....182 fluid, refill capacity ................212 fluid, specifications ..........215,217 Radio ............................................29 Relays ........................................145 Remote entry system ............
Index Vehicle Identification Number (VIN) ..........................................222 Vehicle loading ..........................132 Ventilating your vehicle ...........111 Warning chimes ...........................13 Warning lights (see Lights) .........8 Washer fluid ..............................177 Water, Driving through .............134 240 Windows power .........................................74 Windshield washer fluid and wipers checking and cleaning ............189 operation ....................
Filling station information Item Required fuel Fuel tank capacity Information Unleaded fuel only - 87 octane Refer to Refill capacities in the Capacities and specifications chapter. Engine oil (includes 5.7L (6.0 quarts). Use Motorcraft 5W30 Super filter change) Premium Motor Oil, Ford specification WSS-M2C153-G. Tire size and pressure Refer to the Certification Label inside of driver’s door Hood release Pull handle under the left side of the instrument panel.
