User manual

ManualsBrandsFLUKE ManualsTest & Measurement Accessoriesi1010KITClip-on ammeter adapter 1 - 600 A (up to 10kHz) (±2% +0.5 A) 30 mm

i410/i1010

AC/DC Current Clamp

Instruction Sheet

Read First: Safety Information

• Avoid working alone to ensure that assistance can be rendered.

• Do not use the clamp if the clamp or leads appear damaged, or if you

suspect that the clamp is not operating properly.

• Use extreme caution when working around bare conductors or bus

bars. Accidental contact with the conductor could result in electric

shock.

• Use caution when working with voltages above 30V rms or 60V dc.

Such voltages pose a shock hazard.

• Never use the clamp on a circuit with a voltage higher than 600V

(CAT. III) or a frequency higher than 400 Hz (i410) or 2 kHz (i1010.)

The clamp may be damaged if these limits are exceeded.

• Use the clamp only as specified in this instruction sheet; otherwise,

the protection provided by the clamp may be impaired.

• Read the operating instructions before use and follow all safety

information.

• CAT. III - Industrial Locations (IEC 1010-1).

PN 617677 September 1996, Rev.1, 4/97



Summary of content (8 pages)

PAGE 1
® i410/i1010 AC/DC Current Clamp Instruction Sheet P Read First: Safety Information • Avoid working alone to ensure that assistance can be rendered. • Do not use the clamp if the clamp or leads appear damaged, or if you suspect that the clamp is not operating properly. • Use extreme caution when working around bare conductors or bus bars. Accidental contact with the conductor could result in electric shock. • Use caution when working with voltages above 30V rms or 60V dc. Such voltages pose a shock hazard.
PAGE 2
Features and Connections A Jaw Lever B Jaw Centering Marks CAT C ON Indicator 600V 600A D ON/OFF Switch E Zero Adjust F Battery Access A ZERO G Output Cable i410 CLAMP METER 600V Minimum voltmeter requirements: 76 TRUE RMS MULTIMETER • Accepts safetyshrouded banana plugs. • Can display 1 mV (0.1 mV preferred) • Accuracy ≥ 0.75% • Input impedance ≥ 1 MΩ, ≤100 pF. V ar001i.
PAGE 3
Measuring DC Current Maximum: 400A dc (i410) or 1000A dc (i1010) CAT 600V 600A A ZERO i410 CLAMP METER 600V 76 CAT TRUE RMS MULTIMETER 600V 600A mV A ZERO i410 CLAMP METER 600V ar002i.eps A Connect to voltmeter. B Select mV dc. C Set ON. D Adjust ZERO (jaws empty.) A ZERO ar006i.eps E Clamp and center around conductor. F Read voltmeter (1 mV = 1A.
PAGE 4
Measuring AC Current Maximum: 400A ac rms (i410) or 600A ac rms (i1010) 4 5 6 7 8 9 10 0 Speed i410 76 TER MP ME 600V CLA i410 CAT A ZE RO 600V 600A 600V CAT CLAMP METER A ZERO 600V 600A 3 2 1 TRUE RMS MULTIMETER V ar003i.eps A Connect to voltmeter. B Select mV ac (or V ac, but resolution may be limited to 1A.) C Set ON. D Clamp and center around conductor. E Read voltmeter (1 mV = 1A.
PAGE 5
Testing the Battery A Set OFF. CAT B Select V dc. 600V 600A 76 C ≤ 7.0V dc = replace battery. TRUE RMS MULTIMETER (Voltmeter input impedance ≥ 1 MΩ) A ZERO i410 CLAMP METER V 600V ar004i.eps Replacing the Battery For specified battery life, use an alkaline battery. 1. 2. 3. ar005i.
PAGE 6
If the Current Clamp Does Not Work Check Battery = OK? Voltmeter connections? Voltmeter function/range? CV Correct Refer to “Testing the Battery.” Red to + or Black to mV dc mV ac (or V ac) Storage During longer periods of non-use (> 60 days), remove and store the battery separately. Cleaning Periodically wipe the case with a damp cloth and mild detergent. Do not use abrasives or solvents. Service and Parts The Current Clamp should be serviced only by a qualified service technician.
PAGE 7
i410 i1010 Specified Current Range: Usable Current Range: DC Accuracy (zero adjusted, conductor centered) AC Accuracy 1 - 400A ac rms * 1 - 400A dc 0.5 - 400A 1 - 600A ac rms * 1 - 1000A dc 0.5 - 1000A 3.5% + 0.5A (0 - 400A) 2.0% + 0.5A (01000A) 3.5% + 0.5A, 45 - 400 Hz, Crest Factor ≤ 3. (0 - 400A) Bandwidth 3 kHz 2.0% + 0.5A, 45 - 400 Hz, Crest Factor ≤ 3. 3.0% + 0.5A, 400 Hz 2 kHz sine wave.
PAGE 8
LIMITED WARRANTY & LIMITATION OF LIABILITY Each Fluke product is warranted to be free from defects in material and workmanship under normal use and service. The warranty period is one year and begins on the date of shipment. Parts, product repairs and services are warranted for 90 days.