QUICK Install Guide 400A FILL VALVE VIDEO HOW-TO VIDEO VISIT: FLUIDMASTER.COM *See back page for important legal information.
GETTING STARTED STEP 1: PREPARE TANK TOOLS NEEDED PARTS OVERVIEW Tank Water Level Adjustment Screw Bucket Sponge Towel Scissors A: TURN OFF WATER TURN (Optional) CLOCKWISE B: DRAIN WATER Flush toilet to drain most of the water from the tank.
STEP 2: REMOVE OLD FILL VALVE A: REMOVE CONNECTOR Remove water supply connector from bottom of fill valve by twisting connector nut to the left (clockwise). Towel (Optional) STEP 3: ADJUST HEIGHT OF NEW FILL VALVE A: TWIST FILL VALVE TO ADJUST HEIGHT Top of fill valve cap should measure roughly 3" above top of overflow pipe when installed. LEFT NOTE: Inspect water supply connector. Replace it if it is worn, or you don’t know how old it is, to prevent flooding and property damage.
STEP 4: INSTALL NEW FILL VALVE A: B: C: A: ATTACH WATER SUPPLY CONNECTOR TO FILL VALVE Twist to the right (counterclockwise) PUSH REFILL TUBE ONTO FILL VALVE REFILL PORT B: Refill Tube TOP DOWN VIEW E: **Lever Hole Water Level Overflow Pipe Scissors (Optional) INSTALL LOCKNUT Screw locknut to the right (counterclockwise) onto fill valve shank (below tank). RIGHT *Hand-tighten only. DO NOT OVER TIGHTEN. * Over tightening may crack the fill valve or tank causing flooding.
STEP 6: FINE-TUNE TANK WATER LEVEL STEP 7: FLUSH THE TOILET A: FLUSH THE TOILET If you’re satisfied with the flush, YOU’RE DONE! A: FLUSH THE TOILET TO CHECK THE TANK WATER LEVEL After the water stops filling the tank, the water level should be roughly ½ inch below the top of overflow pipe to ensure a proper flush. 1/2" Overflow Pipe See Step 5C for Full Tank view B: WATER LEVEL IS TOO LOW Turn the tank water level adjustment screw clockwise to raise the float. Flush to reset water level.
TROUBLESHOOTING REPLACE FILL VALVE SEAL IF THE FILL VALVE: • DOES NOT TURN ON • WON’T TURN OFF • WON’T REFILL TANK Turn off water supply. B: Flush toilet. C: With right hand push float up, grip and hold shaft under float. D: With left hand twist cap and lever arm counterclockwise to unlock cap. Let cap hang on float cup. E: Hold empty cup upside down over uncapped valve to prevent splashing. F: Turn water supply on and off a few times. G: Turn water supply off. H: Replace valve cap.
TROUBLESHOOTING FOR CANISTER FLUSH VALVES The Fluidmaster refill clip is not required for installation. If you’ve already installed the refill clip onto the refill tube, simply pull it or cut it off. FOR MANSFIELD® Push refill tube into refill hole at the top of the flush valve cap. ADDITIONAL QUESTIONS? For installation assistance, contact our technical services department. FOR KOHLER® AQUAPISTON EMAIL, CHAT or CALL Push refill tube onto yellow nipple on flush valve. www.fluidmaster.
GUÍA DE INSTALACIÓN RÁPIDA GUÍA DE INSTALACIÓN RÁPIDA VÁLVULA DE LLENADO 400A PASO 1: PREPARE EL TANQUE A: B: INSTALE CON CONFIANZA *Consulte la última página para obtener información legal importante. HERRAMIENTA NECESARIA Balde, Esponja, Toalla, Tijeras EMPEZANDO: RESUMEN DE PIEZAS C: VIDEO VIDEO DE CÓMO HACERLO PASO 2: REMUEVA LA VÁLVULA DE LLENADO ANTIGUA VISITE: FLUIDMASTER.
GUÍA DE INSTALACIÓN RÁPIDA SOLUCIÓN DE PROBLEMAS E: SI LA VÁLVULA DE LLENADO: (PÁGINA 10) INSTALE LA CONTRATUERCA. Atornille la contratuerca hacia la derecha en el vástago de la válvula de llenado (debajo del tanque). *Apriete solo con las manos. NO APRIETE DEMASIADO. PASO 5: PASOS PARA TERMINAR A: • NO SE PRENDE • NO SE APAGA • NO RELLENA EL TANQUE (PÁGINA 7) SUJETE EL CONECTOR DEL SUMINISTRO DE AGUA A LA VÁLVULA DE LLENADO. Gire a la derecha. *Apriete solo con las manos.
SOLUCIÓN DE PROBLEMAS A: B: C: REEMPLACE EL SELLO DE LA VÁLVULA DE LLENADO (PÁGINA 11) Remueva la tapa. Reemplace el sello con un sello *genuino 242 de Fluidmaster. Vuelva a colocar la tapa de la válvula. • Coloque el ensamble de la tapa sobre el cuerpo gris de la válvula alineando el brazo de la tapa y el tornillo de ajuste al lado de la manguera de relleno. • Presione hacia abajo sobre la tapa mientras gira la tapa y el brazo en el sentido de las manecillas del reloj hasta que se asegure.
WARNING DO NOT USE IN-TANK DROP-IN TOILET BOWL CLEANERS CONTAINING BLEACH OR CHLORINE. Use of such products will: (1) RESULT IN DAMAGE to tank components and MAY CAUSE FLOODING and PROPERTY DAMAGE and (2) VOID FLUIDMASTER WARRANTY. Fluidmaster Flush ‘n Sparkle Toilet Bowl Cleaning System is recommended for those choosing to use in-tank bowl cleaners and WILL NOT VOID the FLUIDMASTER WARRANTY because it will not damage the components. DO NOT overtighten nuts or tank/ bowl may crack.
