Installation Instructions

ManualsBrandsFlorCraft ManualsPower Tools4-1/2" Hand Held Tile and Masonry Saw

ALWAYS WEAR ANSI Z87.1 APPROVED

EYE PROTECTION!

FLOR CRAFT

PRODUCT

MANUAL

SKU NUMBER

709-4249

SERIAL NUMBER

CAUTION:

FOR YOUR OWN SAFETY READ

INSTRUCTION MANUAL

COMPLETELY AND

CAREFULLY BEFORE

OPERATING THIS 4-1/2”

CIRCULAR TILE SAW

SAVE THIS MANUAL FOR

FUTURE REFERENCE.

SPECIFICATIONS

Voltage: 120V AC

Cycle: 60Hz, single phase

Power: 10 Amp

No Load Speed: 11,800 rpm

Blade Size: 4-1/2”

Arbor Size: 7/8”

Depth of Cut: 1-1/4”

Angle Capability: 0-45 Degrees

Cord length: 6 ft.

Weight: 7.7 lbs

4-1/2” CIRCULAR TILE SAW

. Operation

. Parts List and Diagram

For questions or problems please call our customer

service line at (888) 315-3080 M-F 8-5 Central Time.

PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn

Summary of content (8 pages)

PAGE 1
FLOR CRAFT® PRODUCT MANUAL SKU NUMBER 709-4249 SERIAL NUMBER CAUTION: FOR YOUR OWN SAFETY READ INSTRUCTION MANUAL COMPLETELY AND CAREFULLY BEFORE OPERATING THIS 4-1/2” CIRCULAR TILE SAW SPECIFICATIONS Voltage: 120V AC Cycle: 60Hz, single phase Power: 10 Amp No Load Speed: 11,800 rpm Blade Size: 4-1/2” Arbor Size: 7/8” Depth of Cut: 1-1/4” Angle Capability: 0-45 Degrees Cord length: 6 ft. Weight: 7.7 lbs SAVE THIS MANUAL FOR FUTURE REFERENCE. ALWAYS WEAR ANSI Z87.
PAGE 2
GENERAL SAFETY INSTRUCTIONS WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electrical shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS WORK AREA • Keep your work area clear, clean and well lit. Cluttered work surfaces and dark areas invite accidents. • Keep people not involved in the work, especially children away from the work area while operating a power tool. Distractions can cause you to lose control of the tool.
PAGE 3
• • • • Store the tool in a secure place out of reach of children. A secure storage location will prevent the unauthorized use by untrained users. Properly maintain tools. Keep all cutting tools sharp and clean. Remove contaminants from the tool and keep clean. Check for broken parts or binding of moving parts before use. If damaged, have the tool serviced before use. Prevent accidents caused by poorly maintained tools. Use only accessories recommended for your model.
PAGE 4
CONTENTS This package contains: ● 1 Marble/tile saw with water tube and hose attachment ● 1 Diamond blade 4-1/2” x 7/8”(bore) ● 1 Socket wrench ● 1 Box wrench ● 1 instruction manual Check the tool and accessories for damage, which could have occurred during transportation. USAGE TIPS ● Always cut one tile at time. ● Be sure motor has reached full speed before starting to cut tile. ● Let the saw blade run freely for a few seconds before cutting a piece of tile.
PAGE 5
● To re-install, fit the blade supplied onto the motor shaft . ● Fit the outer flange and spindle bolt. ● Tighten the spindle bolt by gripping outside flange with box wrench, place socket wrench on spindle bolt and turn socket wrench counter clockwise. Do not over-tighten! Trigger Button (On-Off) The tool can only be put into service if both the Lock Off button and the trigger are depressed. Depressing the trigger turns the tool “on”. Releasing the trigger turns the tool “off”.
PAGE 6
● Hold the tool firmly and turn on the tool. Don’t allow the blade to touch the material until it has attained full speed. ● Slowly and smoothly move the tool forward to cut, keeping the base plate flat on the surface. CAUTION: Don’t forget to open the water value to let the water flow onto the surface of the blade while you start cutting the tile material. The volume of water can be adjusted with the water valve. ● Keep the tool moving forward smoothly and evenly until the cut is complete.
PAGE 7
PARTS LIST No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Description Adjustable Depth Guide Locking Knob Washer Guide Plate Rivet Pole inner Flange Washer Pin Gear Box Sealing Loop Bearing Big Gear Key Spindle Bearing Sealing Washer Blade Guard Washer Spring Washer Screw Inner Flange Sticker Diamond Blade Outer Flange Spindle Bolt Wing Nut Valve Pole Washer Screw Pipe Stand Syphon No.
PAGE 8
SCHEMATIC DRAWING -8 - PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.