USE AND CARE GUIDE
Safety Information Pre-Installation Hardware included Celing Hanging the Fan ················································ ················································ ................................................
The supplier warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a lifetime after the date of purchase by the original purchaser.The supplier also warrants that all other fan parts,excluding any glass or acrylic blades,to be free feom defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the original purchaser.
e\ HARDWARE INCLUDED components table NOTE: Hardware not shown to actual size.
Installation of the hanging bracket (suspension part) LLLLLLLLLLLLLLLLLL LL ~~~~~~~~ LL ~~ LLLL cct:DDO:a:e::rn:::ceHinacc LLL~LLLLLLL ~ ~LL ~ LL For wooden ceiling, use wood screw to drill on the wooden beam or the "junction box" to fix the hanging bracket (selection is made according to actual requirements of the customers). Washers STEP 1A-WOODEN CEILING Se" J: ~ 1 : ' ' f ' · ,; SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX.
1 Making the electrical connections WARNING:Each wire not supplied with this fans is designed to accept up to one 12-gauge house wire and two wires from ~ the fan.If you have larger than 12-gauge house wiring or more than one house wire to connect to the fan wiring,cnsult an electrician for the proper size wire nuts to use. A\ A\ WARNING:Remove the rubber motor stops on the bottom of ~ fan before installing the blades or testing the motor.
, 1 Attaching the blades to the arms 9I I f I 0 I d 1 :Pass the red washer through the screw. 2:Tighten the screw through the blade and tighten it on the arms. 3:Repeat the above steps to tighten the four sets of blades. 01 I I I I I I 1- -:1~ 2 Fastening the blade arms to the motor A\ WARNING:Remove the rubber motor stops on the bottom Ll.1 of the fan before installing the blades or testing the motor. NOTE:Your fan features revolutionary advancements for quick and easy blade installation.
f4ti14hi§PW1, - bht•il - · 1 Connecting lamp wire 1 Attaching the light kit fitter assembly CAUTION :To reduce the risk of electric shock.disconnect the electrical circuit to the fa before installing the light fixture. 1.lnsert the "white" line in the switching box of the motor into the "white"line of the light and tie insulated rubber tape. 2.lnsert the "bule"line in the switching box of the motor into the "blue"line of the light and tie insuklated rubber tape. 2 Tighten the screw of the box cover. 1.
Install the shade WARNING:Allow the shatter resistant bowl to � cool completely before removing. A A CAUTION: Make sure the power is off before attaching or removing the shatter resistant bowl. CAUTION:Do not over tighten the hex nut,overtightening the hex nut may cause the shatter resistant bowl to break. [2] t E26 MAX 60W*3PCS (hand pull chain only) OPERATING YOUR FAN Turn on the power and check the operation of the fan.The fan pull chain controls the fan speed as follows: 1.
remote control ILOwl IMEDI [Bil ISTOPI LIGHT NO/OFF [8] ~ ~ ru:i) FanSpeed Low Level FanSpeed Middle Level FanSpeed High level FanSTOP LIGHT NO/OFF Auto off after 1hr Auto off after 2hr Auto off after 4hr Auto off after 8hr From controller FOR AC IN L FOR AC INN Ground wire 1 :The 2:The 3:The 4:The 5:The motor "green" wire to the "Ground wire"wire From outside Outlet Box.
WARN I NG:Make sure the power is off before cleaning your fan. □ Because of the fan's natural movement, some connections may become loose.Check the support connections,brackets,and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the celling. □ Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor or the wood, or possibly cause an electrical shock.
Series general specifications USE AND CARE GUIDE