Multi-Angle Utility Bench MPORTANT: Read all instructions carefully before using this product. Retain this owner’s manual for future reference. The specifications of this product may vary from this photo and, subject to change without notice. 2861.
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE. If you need help with product information, assembly, or replacement parts. Please contact customer service. Email us at: Service@paradigmhw.
TABLE OF CONTENTS SERVICE-------------------------------------------------------------------- 2 LABEL PLACEMENT----------------------------------------------------- 3 PRODUCT SAFETY------------------------------------------------------ 4 ASSEMBLY PREPARATION-------------------------------------------- 5 OVERVIEW----------------------------------------------------------------- 6 HARDWARE PACK-------------------------------------------------------- 8 PART LIST---------------------------------------
SERVICE IMPORTANT: FOR NORTH AMERICA ONLY For damage or defective product, questions, replacement parts or any other service support, please contact our customer service department (8:00 AM - 5:00 PM Pacific Standard Time, Open Daily) by below methods: For Best Service Email: Service@paradigmhw.com Website: www.paradigmhw.
LABEL PLACEMENT 3
PRODUCT SAFETY WARNING: Before using this equipment you should consult with your physician to see if this Bench is appropriate for you. Do not use this equipment without your physician’s approval.
ASSEMBLY PREPARATION Warning: It is highly recommend that you have assistance during the assembly of this strength equipment. 1. Tools for assembly: General tools you may need for the assembling this strength equipment: • Metric Allen Key Set • Metric Wrench Set and Adjustable Wrench • Flat Screwdrivers • Phillips Screwdrivers • Rubber Mallet • Silicone Spray Oil 2. Insert the bolts into the frame as illustrated in the drawing of each of the steps. 3.
OVERVIEW DRAWING 6
OVERVIEW DRAWING 7
HARDWARE PACK NO.120 Round Cap D25.4xD65x31.
PART LIST Part# Description Q’ty. Part# Description Q’ty. A Main Frame 1 7 Hex Bolt M12x1.75x80L 2 B Front Stabilizer 1 8 Hex Bolt M12x1.75x105L 4 C Rear Stabilizer 1 9 Hex Bolt M12x1.75x110L 2 D Backrest Frame 1 10 Hex Bolt M12x1.75x125L 1 E Seat Plate 1 12 Allen Bolt M8x1.25x40L 2 F Seat Adjustment Arc 1 13 Bolt M5x0.8x10L 2 G Backrest Post 1 50 Flat Washer D18xD8.5x1.2T 10 H Sleeve 1 52 Flat Washer D24xD13.5xD2.
PART LIST Part# Description Q’ty. Part# Description Q’ty. 157 Square Cap 50x50x20L 2 220 Square Bushing 60x60x200L 1 180 Buffer 52x52x5T 1 221 Wheel D70.5x23 2 181 Buffer 75x75x5T 2 222 Foam Roller D23xD100x200L 4 182 Buffer D70x5T 2 223 Sleeve D100x200 4 1 270 2 271 183 201 203 Buffer D20x10LxM8x1.25 Hand Grip D24x100x3T Hand Grip 3Tx125L 1 10 Bushing D29xD12.1x9T Bushing D22.2xD8.
11
STEP 1 1A. Attach Front Stabilizer (B) onto the Main Frame (A) by using: 2 - (8) Hex Bolt M12x1.75x105L 2 - (76) Nylon Nut M12x1.75x12T 4 - (52) Flat Washer D24xD13.5x2.5T 1B. Attach Rear Stabilizer (C) onto the Main Frame (A) by using: 2 - (8) Hex Bolt M12x1.75x105L 2 - (76) Nylon Nut M12x1.75x12T 4 - (52) Flat Washer D24xD13.5x2.
STEP 1 Open Wrench 2PCS NO.8 Hex Bolt M12x1.75x105L 4PCS NO.76 Nylon Nut M12x1.75x12T 4PCS 13 NO.52 Flat Washer D24xD13.5x2.
STEP 2 2A. Remove twist ties From Main Frame (A), but leave the two Bushing (270) parts in place. 2B. loosen the Ball Knob Pop Pin (102) on the Main Frame (A) to allow for the insertion of the Seat Adjustment Arc (F). 2C. Insert the Seat Adjustment Arc (F) into the slot on the Main Frame (A) and secure it in place by inserting it into one of the holes of Seat Adjustment Arc (F) and tighten the Ball Knob Pop Pin (102), as shown in Fig AA-2 2D.
STEP 2 Open Wrench 2PCS NO.10 Hex Bolt M12x1.75x125L 1PC NO.76 Nylon Nut M12x1.75x12T 1PC 15 NO.52 Flat Washer D24xD13.5x2.
STEP 3 3A. Remove twist ties From Backrest Post (G), but leave the two Bushing (270) parts in place. 3B. Attach Backrest Post (G) onto the Backrest Frame (D) by using: 1 - (9) Hex Bolt M12x1.75x110L 1 - (76) Nylon Nut M12x1.75x12T 2 - (52) Flat Washer D24xD13.5x2.5T Note: Make sure the circular hand grip tube of Backrest Post (G) is on the underside during installation.
STEP 3 Open Wrench 2PCS NO.9 Hex Bolt M12x1.75x110L 1PC NO.76 Nylon Nut M12x1.75x12T 1PC 17 NO.52 Flat Washer D24xD13.5x2.
STEP 4 4A. Attach the Attachment Holder (I) to the front of Main Frame (A) and Fixing Plate (J) to the rear of Main Frame (A) by using: 2 - (7) Hex Bolt M12x1.75x80L 2 - (76) Nylon Nut M12x1.75x12T 4 - (52) Flat Washer D24xD13.5x2.5T Note: If you do not intend on using the Leg Hold Down, do not install the Attachment Holder (I).
STEP 4 Open Wrench 2PCS NO. 7 Hex Bolt M12x1.75x80L 2PCS NO.76 Nylon Nut M12x1.75x12T 2PCS 19 NO.52 Flat Washer D24xD13.5x2.
STEP 5 5A. Attach the Seat Pad (L) onto the Seat Plate (E) by using: 4 - (3) Hex Bolt M8x1.25x25L 4 - (54) Spring Washer D15.4xD8.2x2T 4 - (50) Flat Washer D18xD8.5x1.2T Note: loosely install all the hardware by hand prior to tightening with tools.
STEP 5 Open Wrench 1PC NO. 3 Hex Bolt M8x1.25x25L 4PCS NO.54 Spring Washer D15.4xD8.2x2T 4PCS 21 NO.50 Flat Washer D18xD8.5x1.
STEP 6 6A. Attach the Backrest Pad (K) and Head Pad (M) onto the Backrest Frame (D) by using: 6 - (3) Hex Bolt M8x1.25x25L 6 - (54) Spring Washer D15.4xD8.2x2T 6 - (50) Flat Washer D18xD8.5x1.2T Note: loosely install all the hardware by hand prior to tightening with tools.
STEP 6 Open Wrench 1PC NO. 3 Hex Bolt M8x1.25x25L 6PCS NO.54 Spring Washer D15.4xD8.2x2T 6PCS 23 NO.50 Flat Washer D18xD8.5x1.
STEP 7 7A. Loosen Ball Knob Pop Pin (102) then mount Leg Hold Down (P) into Attachment Holder (I) and Secure into position by tightening the Ball Knob Pop Pin (102). 7B. Insert a Foam Roller Tube (Q) midway along its length into the upper holes on the Leg Hold Down (P). Use Two Foam Roller (222 & 223) and slide one on to each exposed side of the Foam Roller Tube (Q). Insert a Round Cap (120) on to each side of Foam Roller Tube (Q) using: 2 - (120) Round Cap D25.4xD65x31.
STEP 7 NO.120 Round Cap D25.4xD65x31.
ADJUSTMENTS 1. Seat Adjustment (View AA-8) Lift or lower the Seat Pad (L) to desired position and secure it in place with Ball Knob Pop Pin (102) before using the Multi-angle Utility Bench. 2. Backrest Adjustment (Views AA-4, AA-5, AA-6, and AA-7) Lift or lower the Backrest Post (G) to the desired angle for the Backrest Pad (K) before using the Multi-angle Utility Bench.
ADJUSTMENTS 3. Leg Hold Down Adjustment Lift or lower the Leg Hold Down (P) to desired position and secure it in place with Ball Knob Pop Pin (102) before using the Multi-angle Utility Bench. 4. Transporting the Bench (AA-9) Grab and hold Front Stabilizer (B), then carefully lift the Front Stabilizer (B) until the wheels on the Rear Stabilizer (C) make contact with the ground.
WARRANTY MANUFACTURER’S LIMITED WARRANTY Paradigm Health & Wellness guarantees to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s Manual.
PART REQUEST FORM Paradigm Health & Wellness, Inc. EMAIL THIS FORM WITH YOUR RECIEPT OF PURCHASE TO Service@paradigmhw.
