INSTALLATION INSTRUCTIONS Backguard for Professional Ranges BGRV2 models US CA www.dcsappliances.com 591091A 04.
1 ! SAFETY AND WARNINGS ● WARNING! ● Cut Hazard Take care - panel edges are sharp. Failure to use caution could result in injury or cuts. ● ● IMPORTANT SAFETY INSTRUCTIONS! ● ● ● ● Save these instructions for the local inspectors use. To avoid hazard, follow these instructions carefully before installing or using this product. Please make this information available to the person installing the product - doing so could reduce your installation costs.
MODEL IDENTIFICATION RANGE MOUNT LOW BACKGUARD BGRV2-1230 BGRV2-1236 BGRV2-1248 BGRV2-3036 BGRV2-3048 WALL MOUNT HIGH BACKGUARD LOW SHELF BGRV2-3030 WALL MOUNT HIGH BACKGUARD HIGH SHELF AND ANGLED VENT TRIM BGRV2-3030H BGRV2-3036H BGRV2-3048H 3
INSTALLATION SCENARIOS AND USE OF BACKGUARDS WALL INSTALLATION Combustible Surface Non-combustible surface* (required) Range Mount Low Backguard Min.
4 INSTALLATION SCENARIOS AND USE OF BACKGUARDS Important notes ● ● All ranges come fitted standard with with either an Integral Flat Vent Trim or an Angled Vent Trim (RGCV2-305 models only) There are three different backguards available for purchase: Range Mount Low Backguard ● Wall Mount High Backguard with Low Shelf ● Wall Mount High Backguard with High Shelf, also supplied with an Angled Vent Trim.
5 PRODUCT DIMENSIONS WALL MOUNT HIGH BACKGUARD LOW SHELF RANGE MOUNT LOW BACKGUARD WIDTH WIDTH 5 7/8” (150mm) 10 3/8” (263mm) 10 15/16” (278mm) 29 1/8” (740mm) 8 13/16” (224mm) 1/2” (13mm) FRONT PROFILE 1/2” (13mm) FRONT PROFILE WALL MOUNT HIGH BACKGUARD HIGH SHELF WIDTH 5 3/8” (136mm) 26 1/2” (673mm) 9 1/16” (230mm) FRONT 6 1 5/16” (33mm) PROFILE SUITABLE RANGE RANGE MOUNT LOW BACKGUARD WALL MOUNT HIGH BACKGUARD LOW SHELF WALL MOUNT HIGH BACKGUARD HIGH SHELF BACKGUARD WIDTH 30” models
6-A RANGE MOUNT LOW BACKGUARD - ASSEMBLY 1 Attach low backguard to the rear of the range 1 Align the backguard with the range, so that it rests on the vent trim. 2 Fasten the bottom of the backguard to the rear of the range using all the screws provided, as shown. The two center screws come already attached to the range for your convenience. Finally position range 3 Push the range into position. Follow the rest of the instructions shown in the range installation instructions.
6-B 1 WALL MOUNT HIGH BACKGUARD WITH LOW SHELF - ASSEMBLY 1 Recommended installation order: 1] VENT HOOD 2] BACKGUARD 3] RANGE VENT HOOD #10 machine screws End cap Locate and Mark the two mounting screw locations 2 Use the diagram below depending on your particular model. Center stanchion BACKGUARD Rod Attach rod etc 3 Attach rod, end caps and center stanchion to backguard with #10 machine screws supplied. End cap 3 RANGE continued over...
6-B Upper mounting screws WALL MOUNT HIGH BACKGUARD WITH LOW SHELF - ASSEMBLY 1/16” (2mm) 6 5 Ensure backguard is snug tight with the bottom of the vent hood and wall 4 Mount Backguard to wall 4 Use the marked holes to locate the upper mounting screw locations on the wall. Pre-drill and install flange head screws (not supplied), leaving 1/16” (1mm) between the screw head and wall. 5 Place the backguard onto the screws by lining up the screw heads with the rear mounting slots.
6-C WALL MOUNT HIGH BACKGUARD WITH HIGH SHELF - REPLACE THE VENT TRIM 2 Remove the flat vent trim 1 If using the high backguard with high shelf, you must install the angle trim (supplied) first. First, remove the two screws at the back of the trim as shown. 2 Carefully lift off the flat vent trim and also the pan supports/griddle/grill frame etc. Flat Vent Trim IMPORTANT! Be careful not to touch any exposed electrical wiring or internals at this stage.
6-C WALL MOUNT HIGH BACKGUARD WITH HIGH SHELF - ASSEMBLY Choose slots VENT HOOD 1 1 Recommended installation order: 1] VENT HOOD 2] BACKGUARD 3] RANGE 2 Back section 30 ” 36 MOD /48 EL ”M S= OD 16 EL ” (4 S = 06 32 mm ”( 813 ) mm BACKGUARD ) RANGE 1/4” (6mm) Locate and Mark the mounting screw locations for backguard back section 2 After unpacking all backguard parts, position the back section so that it’s 1/4” (6mm) and centered above the Vent Trim attached to the range.
7 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER GENERAL Correct and suitable placement of the appliance and backguard. Specified clearances maintained to cabinet surfaces. Specified clearances maintained to either combustible or non-combustible surfaces. Backguard centered under hood and level - front to back, side to side and is securely fastened to the appliance (Range Mount Low Backguard only) or to the wall. All packaging material and tie straps removed.
INSTALLATION INSTRUCTIONS Backguard for Professional Cooktops BGCV2 models US CA www.dcsappliances.com 591091A 04.
1 ! SAFETY AND WARNINGS ● WARNING! ● Cut Hazard Take care - panel edges are sharp. Failure to use caution could result in injury or cuts. ● ● IMPORTANT SAFETY INSTRUCTIONS! ● ● ● ● Save these instructions for the local inspectors use. To avoid hazard, follow these instructions carefully before installing or using this product. Please make this information available to the person installing the product - doing so could reduce your installation costs.
3 MODEL IDENTIFICATION WALL MOUNT LOW BACKGUARD BGCV2-1230 BGCV2-1236 BGCV2-1248 BGCV2-3036 BGCV2-3048 WALL MOUNT HIGH BACKGUARD LOW SHELF BGCV2-3030 WALL MOUNT HIGH BACKGUARD HIGH SHELF BGCV2-3030H BGCV2-3036H BGCV2-3048H 3
4 COOKTOP INSTALLATION SCENARIOS AND USE OF BACKGUARDS WALL INSTALLATION Combustible Surface Non-combustible surface* (required) Wall Mount Low Backguard Min. 6” (152mm) Clearance cooking surface cooking surface Non-combustible surface* (required) cooking surface Min.
4 COOKTOP INSTALLATION SCENARIOS AND USE OF BACKGUARDS Important notes ● There are three different backguards available for purchase: ● Wall Mount Low Backguard ● Wall Mount High Backguard with Low Shelf ● Wall Mount High Backguard with High Shelf. ● For installations against non-combustible* surfaces only, you may install the cooktop without a backguard or choose any of the three backguards.
5 PRODUCT DIMENSIONS WALL MOUNT HIGH BACKGUARD LOW SHELF WALL MOUNT LOW BACKGUARD WIDTH WIDTH 5 7/8” (150mm) 12" (305mm) 10 15/16” (278mm) 15/16" (23mm) 30” (762mm) FRONT PROFILE 8 13/16” (224mm) 15/16” (23mm) FRONT PROFILE WALL MOUNT HIGH BACKGUARD HIGH SHELF WIDTH 5 3/8” (136mm) 30” (762mm) 9 1/16” (230mm) FRONT 15/16” (23mm) PROFILE 6 WALL MOUNT HIGH BACKGUARD LOW SHELF WALL MOUNT HIGH BACKGUARD HIGH SHELF SUITABLE RANGE WALL MOUNT LOW BACKGUARD 30” models BGCV2-1230 BGCV2-3030 BG
6-A WALL MOUNT LOW BACKGUARD - ASSEMBLY Use slots to correctly position 1 Back section VENT HOOD 2 30 ” 36 MOD /48 EL ”M S= OD 16 EL ” (4 S = 06 32 mm ”( 813 ) mm ) 1 Recommended installation order: 1] VENT HOOD 2] BACKGUARD 3] COOKTOP Locate and Mark the mounting screw locations for back section 2 After unpacking all backguard parts, position the back section so that it’s 1/4” (6mm) and centered 1/4” above the cooktop trim.
6-B WALL MOUNT HIGH BACKGUARD WITH LOW SHELF/HIGH SHELF - ASSEMBLY Use slots to correctly position 1 Back section VENT HOOD 1 Recommended installation order: 1] VENT HOOD 2] BACKGUARD 3] COOKTOP 2 30 ” 36 MOD /48 EL ”M S= OD 16 EL ” (4 S = 06 32 mm ”( 813 ) mm BACKGUARD ) COOKTOP 1/4” (6mm) Locate and Mark the mounting screw locations for back section 2 After unpacking all backguard parts, position the back section so that it’s 1/4” (6mm) and centered above the cooktop trim.
7 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER GENERAL Correct and suitable placement of the appliance and backguard. Specified clearances maintained to cabinet surfaces. Specified clearances maintained to either combustible or non-combustible surfaces. Backguard centered under hood and level - front to back, side to side and sits flush with the top of the cooktop trim. All packaging material and tie straps removed. Front section of backguard is securely attached to the back section.
10
11
