Installation Guide
Table Of Contents
- 1 Safety and warnings
- 2 Components
- 3 Tools
- 4 Appliance and cavity dimensions
- 5 Cabinetry options
- 6 Door panel dimensions
- 7 Custom door panel installation dimensions — RS32A72
- 7 Custom door panel installation dimensions — RS36A72
- 8 Custom door panel installation template (RS32A72)
- 8 Custom door panel installation template (RS36A72)
- 9 Door clearance
- 10 Electrical and plumbing
- 11 Before installation
- 12 Cavity preparation
- 13 Water supply connection
- 14 Power supply connection
- 15 Installation preparation
- 16 Top trim installation
- 17 Positioning into cabinetry
- 18 Aligning inside cabinetry
- 19 Door panel installation — stainless steel
- 20 Door panel installation — custom
- 21 Fixing to cabinetry
- 22 Water filter installation
- 23 Toe kick installation
- 24 Covers and trims installation
- 25 Cabinet trims installation — [A] flexible spring clip method
- 26 Cabinet trims installation — [B] fixed screw method
- 27 Final checklist
- 1 Consignes de sécurité et mises en garde
- 2 Pièces
- 3 Outils
- 4 Dimensions de l’appareil et de la cavité
- 5 Options d’armoires
- 6 Dimensions de panneau de porte
- 7 Dimensions d’installation de panneau de porte sur mesure — RS32A72
- 7 dimensions d’installation de panneau de porte sur mesure — RS36A72
- 8 GABARIT D’INSTALLATION DE PANNEAU DE PORTE sur mesure — RS32A72
- 8 GABARIT D’INSTALLATION DE PANNEAU DE PORTE sur mesure — RS36A72
- 9 DÉGAGEMENT DE LA porte
- 10 Raccordement électrique et plomberie
- 11 Avant l’installation
- 12 Préparation de la cavité
- 13 Connexion d'alimentation en eau
- 14 Connexion d'alimentatioN
- 15 préparation de l'installation
- 16 installation de la garniture supérieure
- 17 positionnement dans les armoires
- 18 alignement dans les armoires
- 19 installation de panneau de porte — En acier inoxydable
- 20 Installation de panneau de porte — sur mesure
- 21 Fixation aux armoires
- 22 Installation du filtre à eau
- 23 Installation de la plinthe
- 24 INSTALLATION DES GARNITURES DE PORTE ET TIROIR
- 25 Installation des garnitures de bâti — [A] méthode avec clip de fixation flexible
- 26 Installation des garnitures de bâti — [B] méthode avec vis fixée
- 27 Liste de vérification finale
19
!2 CAVITY PREPARATION
Internal box
A
Anti tip
bracket kit
Anti-tip bracket
(1)
Masonry plug
(4)
#10x40
Pan Head
Philips Screw
#10x40
Pan Head
Philips Screw
#10x40 cross-head screw
(4)
Tools
Cross-head screwdriver
Powered driver (optional)
Pencil
IMPORTANT!
●
The anti-tip bracket and fittings supplied must be fitted to the wall
ofthefinished enclosure to withstand 220lbs (100kg) load.
●
Ensure that anti-tip bracket is installed correctly to prevent the
appliancetipping forward when door is open.
●
Ensure the bracket is secured to structural beams or wall studs
nearesttothe center of the alcove.
WARNING!
Read the following before fastening with masonry plugs and / or screws:
●
Ensure the screws avoid electrical, gas and water conduits.
●
Ensure lightweight masonry material such as cinder block
andnewconcrete (no curing time) are not used in installation.
●
Do not use metallic materials that may corrode, stain and / or
damagetheenclosure.
Attach anti-tip bracket
If the minimum 60mm
overlap cannot be
achieved, install a solid
spacer to the wall stud
behind the bracket.
IMPORTANT!
When positioning the appliance
in the cabinetry, ensure that the
anti-tip bracket overlaps the
appliance by a minimum 2 3/8"
(60mm) for a secure hold.
.
2 3/8" (60mm)
overlap
.
2 3/8" (60mm)
overlap
Anti-tip
bracket
Spacer
Anti-tip
bracket
D
E
B
C
1
Project horizontally from the bottom edge of the finished enclosure towards
the center of the back wall (A). This will locate the contact surface between
the bracket and appliance.
2
Mark the location for placement of the anti-tip bracket. Place the bracket so
the top edge of the contact surface aligns with the mark (B).
3
Mark the locations of the screw holes on the wall based on the most central
wall stud (C).
4
Drill screw holes to the marked locations.
5
For wooden/plaster board wall installation:
– Fix the bracket to the wall with 10x40 pan head cross-head screws, and
screw tightly (D).
6
For solid wall installation:
– Hammer masonry plugs into the wall until flush.
– Fix the bracket to the wall with 10x40 pan head cross-head screws
(4x), and screw tightly (E).
Anti-tip
bracket
A