Product Label

HEAVY DUTY ASBESTOS ENCASEMENT COATING
Wetting Agent
Heavy Duty Encapsulant
Asbestos Encapsulant
SerpiLoc
TROWELABLE
6
2
11131
94235
2418-5
SerpiMastic Heavy Duty Asbestos Encasement Coating
is a high solids, water based, high performance mastic
coating. SerpiMastic dries to an ultra durable, weather-
resistant protective coating that provides high impact
protection for asbestos, cement asbestos board and
thermal/insulations on boilers, pipes and ducts.
SerpiMastic’s one coat system saves valuable time and
greatly reduces costs when compared to removal and
re-insulation of pipes and boilers.
SURFACE PREPARATION
Warning! If you scrape, sand, or remove old paint from
any surface, you may release lead dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH approved respirator to
control lead exposure. Carefully clean up with a wet
mop or HEPA vacuum. Before you start, nd out how
to protect yourself and you family by contacting the
U.S. EPA/Lead Information Hotline at 1-800-424-LEAD
(5323) or log on to www.epa.gov/lead.
Surfaces to be protected should be free of excessive
loose dirt or oil. SerpiMastic Coating will bond tightly
to virtually any surface.
For repairs of large damaged areas, weak insulation
or areas requiring greater mechanical strength apply
Fiberlock Lag-Kloth or Serpi Wet-Wrap ‘N’ Seal prior to
SerpiMastic.
APPLICATION TOOLS
Apply with trowel or brush. SerpiMastic Trowelable
can be applied using any ordinary steel mason’s
trowel or similar spreading tool. For smoother nish
use a wet trowel.
PRODUCT APPLICATION
SerpiMastic is supplied ready to use, thinning is not
required or recommended.
SerpiMastic is a water-based coating material. Coating
application thickness, temperature and humidity will
aect drying rate. Drying time can be minimized by
applying several thinner coats, with 24 hours drying
time between each coat. SerpiMastic Trowelable can
be applied in a single application up to 500 mils (12.7
mm) thick without cracking or shrinking.
COVERAGE
18.5 ft
2
/gal. @ 63 dry mils
DRYING TIME @ 70
o
F 50% R.H.
To Touch: 2 Hours
Completely Dry: 48 Hours
High humidity may retard drying
CLEANUP
Clean tools and drippings with warm soapy water
before SerpiMastic dries. The coating and any
contaminated diking material should be thoroughly
air dried and collected into drums. The drums should
be sealed and labeled and land-lled or incinerated
according to local, regional and national regulations.
PRECAUTIONS
Do not ingest. Do not apply to energized electrical
conductors. Always use goggles or suitable eye
protection. If product is accidentally ingested, unless
contraindicated, administer two or more glasses
of water and induce vomiting. If more than trace
amounts have been ingested seek medical advice.
Wash areas of skin contact with soap & water. Consult
Safety Data Sheet for additional information.
Do not add water. Keep lid on until ready to use.
Stir thoroughly. Do not mix with any other coatings,
solvents or colors in oil. Apply on when air and surface
temperature are below 40°F and 90°F. Do not apply
when drying conditions are poor. Use adequate
ventilation during application. Store in a dry place at
temperatures between 40°F and 90°F. Keep closures
tight and containers upright to prevent leakage.
Product is non-combustible.
Approved respirators must be used to prevent
inhalation of asbestos bers that may be present in the
air. Protective clothing should be worn.
All asbestos abatement activities must be performed in accordance with all applicable regulations including EPA,
OSHA, Federal, State and Local. For more information always contact the appropriate agencies prior to beginning
any abatement project.
DO NOT ADD WATER. KEEP LID ON UNTIL READY TO USE.
CAUTION!
KEEP OUT OF REACH OF CHILDREN.
Do not take internally. Close container after each use.
Keep from freezing. Store between 40°F and 90°F
24 hour Emergency “CHEM-TEL” - 1-800-255-3924
Calculated VOC: 20 g/l
• One Coat System
• Indoor or Outdoor Use
• Contains No Plasticizers or Fiberglass
• Weather Resistant
• Trowel or Brush Application
• UL Approved UL1479, ASTM E814 &
E119, Time Temperature Curve
2418-5
White
NET CONTENTS: 5 Gallons (18.9 L)
For Professional Use Only
ENCAPSULANT MATERIALS
FIRE RESISTANCE CLASSIFICATION
FOR USE WITH CLASSIFIED SPRAY-APPLIED FIRE-RESISTIVE MATERIALS
ABILITY OF THIS MATERIAL TO ACT AS A SEALANT HAS NOT BEEN INVESTIGATED
SEE UL FIRE RESISTANCE DIRECTORY
95S1
For Technical Information call 800.342.3755
These suggestions and data are based on information we believe to be reliable. They are offered in good faith, but without
guarantee, as conditions and methods of use of this product are beyond our control. Neither Fiberlock Technologies, nor its
agents shall be responsible for the use of this product or any procedures or apparatus mentioned. We recommend that the
prospective user determine the suitability of this product , for each specific project and for the health and safety of personnel
working in the area.
For additional information check Safety Data Sheet (SDS) or Product Data Sheet (PDS) available online at www.serpisystems.
SerpiMastic , the Serpi Mastic Logo and other marks in this literature are trademarks of ICP Construction, Inc.
FIBERLOCK SERPI-MASTIC TROWELABLE 2418
DANGER | DANGER
H319 - Causes serious eye irritation.
H350 - May cause cancer.
H360 - May damage fertility or the unborn child.
H373 - May cause damage to organsthrough prolonged or
repeated exposure.
H411 - Toxic to aquatic life with long lasting eects.
Obtain special instructions before use.; Do not breathe
dust/fume /gas/mist/vapours/spray.; Use personal
protective equipment as required.; Avoid release to the
environment.; Wear protective gloves/protective clothing/
eye protection/face protection.; See SDS for full list of P
phrases
IF exposed or concerned: Get medical advice/attention.; IF
IN EYES: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do. Continue
rinsing.; Get medical advice/attention if you feel unwell.; If
eye irritation persists: Get medical advice/attention.; Collect
spillage.; See SDS for full list of P phrases
Canadian Contact Info:
4050-B Sladeview Crescent Suite 200
Mississauga, ON L5L 5Y5 Canada
H319 - Provoque une sévère irritation des yeux.
H350 - Peut provoquer le cancer.
H360 - Peut nuire à la fertilité ou au fœtus.
H373 - Risque présumé d’eets graves pour les organes à la
suite d’expositions répétées ou d’une exposition prolongée.
H411 - Toxique pour les organismes aquatiques, entraîne
des eets néfastes à long terme.
Se procurer les instructions avant utilisation.|Ne pas respirer
les poussières/fumées/gaz/brouillards/vapeurs
/aérosols.|Utiliser l’équipement de protection individuel
requis.|Éviter le rejet dans l’environnement.|Porter des gants
de protection/des vêtements de protection/un équipement
de protection des yeux/du visage.|Voir SDS pour la liste
complète des phrases P
EN CAS d’exposition prouvée ou suspectée: Consulter un
médecin.|EN CAS DE CONTACT AVEC LES YEUX: rincer avec
précaution à l’eau pendant plusieurs minutes. Enlever les
lentilles de contact si la victime en porte et si elles peuvent
être facilement enlevées. Continuer à rincer.|Consulter un
médecin en cas de malaise.|Si l’irritation oculaire persiste:
consulter un médecin.|Recueillir le produit répandu.|Voir
SDS pour la liste complète des phrases P
150 Dascomb Rd.
Andover, MA 01810
[phone]
www.fiberlock.com
Rev. 10.17.18
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov