Specification

ManualsBrandsFastStone+ ManualsFlooringBlack Line 6 in. x 9 in. Slate Peel and Stick Wall Tile (4.5 sq. ft. / pack)

575 Broadhollow Road (Rt. 110), Farmingdale, NY 11735 Tel: 631-390-5925 Fax: 631-390-8522 Email: info@richterrevo.com Website: www.richterrevo.com

Product Information | Technical Datasheet

FastStone+ is bonded with 3M PE Form Tape. It sticks fast and hard so accurate placement “the rst time” is

required because it will not come o easily and damage may occur to the surface it was applied to while trying to

remove the FastStone+.

Before applying to the surface, make sure that the surface it is being applied to is free of dust, dirt and oils. After

peeling o the protective cover on the backing, be careful as to the placement of the product since the adhesion is

immediate and permanent.

Fast and easy direct application on all at, clean, oil and dust free surfaces. For decorative designs of all kinds,

ideal for walls, ceilings, displays or for “DIY”. If used for direct application, it is recommended to use exact cut-

to-size sheets.

FastStone+ COLLECTION: Indian Autumn, Copper, Black Line, Silver Shine. All other colors available on a

special order basis. Minimum quantaties may apply.

Above mentioned FastStone+ is available in sizes 3” x 6”, 6” x 6”, 6” x 9”, 12” x 12”, 12” x 24”.

Sizes can be produced as per customers requirements. Minimum quantities may apply.

COMPOSITION

FastStone+ is natural stone veneer laminated to a berglass/polyester resin substrate bonded with 3m PE foam

tape adhesive.

Summary of content (8 pages)

PAGE 1
Product Information | Technical Datasheet FastStone+ is bonded with 3M PE Form Tape. It sticks fast and hard so accurate placement “the first time” is required because it will not come off easily and damage may occur to the surface it was applied to while trying to remove the FastStone+. Before applying to the surface, make sure that the surface it is being applied to is free of dust, dirt and oils.
PAGE 2
PREPARATION Before application it may be necessary to clean, brush, or degrease any surface of dust or oils. To obtain optimum adhesion, the bonding surfaces must be clean, dry and well unified. Some typical surface cleaning solvents are isopropyl alchohol or N-heptane. Note: Carefully read and follow the manufacturer’s precatutions and directions for use when working with solvents.
PAGE 3
CUTTING Cutting straight lines and curves is best done using long nosed tin snips. FastStone+ can also be cut with a metal shear, wet saw, or table saw with carbide blade. Stone-Veneer can be worked with any commercially available tools (DIY tools). Sawing, drilling, milling, cutting, bending, pressing. For industrial processing we recommend using diamond blade tools due to strong wear on wood blades.
PAGE 4
VARIATIONS Since FastStone + is a natural product DESIGNED BY NATURE, color and texture variances are not defects within the material, but are inherent to it and part of the natural beauty of quarried materials. cannot be guaranteed to match dye-lot to dye-lot, so it is recommended that orders take into account future maintenance or re-fit possibilities. UV & TEMPERATURE The stone surface of FastStone + like most stone elements, acts as a UV inhibitor and will resist high sun conditions for years.
PAGE 5
Application Techniques: Bond strength is dependent upon the amount of adhesive-to-surfqace contact developed. Firm application pressure helps develop better adhesive contact and improves bond strength. Application Ideas - 1600T series tapes are specially formulated for many indoor/outdoor high performance purpose mounting and joining applications, including binding to many Plastics, where moderate temperature and shear performance are required.
PAGE 6
Test Method: US code of federal regulations Part. 1500.44, Titel 16 Flammability Test on Rigid and Pliable Solids: Sample Burning Rate: Polyester Resin based Metalized Panel: PASS inch/sec 0.004 *A sample is considered to have passed the test if the burning rate is not more a 0.10 inch per Second. Test method: As specified in AOAC 16th Ed. Section 973.32 & 973.82 Polyester resin-based- metallized panel / bowl Lead and Cadmium content in earthenware quantilation by AAS: PASS SGS Laboratory No.
PAGE 7
Migration of Certain Elements Soluble Lead (Pb), mg/kg Soluble Antimony (Sb), mg/kg Soluble Arsenic (As), mg/kg Soluble Barium (Ba), mg/kg Soluble Cadmium (Cd), mg/kg Soluble Chromium (Cr), mg/kg Soluble Mercury (Hg), mg/kg Soluble Selenium (Se), mg/kg 04249 12.7 <5 60 0.2 <0.5 <0.5 7.5 <0.5 <0.5 Limit 90 mg/kg mg/kg 25 mg/kg 1000 mg/kg 75 mg/kg 60 mg/kg 60 mg/kg 500 mg/kg Methodology: with reference to EN 71 Part 3.
PAGE 8
Test conducted at testing laboratory which is ISO 9001:2000 approved internationally SLATE QUARTZITE 7. Waterabsorption in % bu wt 2.50 1.90 ASTM C-121 8. Waterabsorption in % Test carried out on thin slate specimen pasted on marble piece 0.17 0.12 ASTM C-97 9. Abrasion Test Average wear, mm Max wear on individual specimen, mm 0.70 0.80 0.90 1.00 IS: 9162-1979 guidelines TEST VALUE 10. Density (mass per unit area Kg/m2 1.45 1.