FANAWAY EVO2 CEILING FAN • • • • INSTALLATION OPERATION MAINTENANCE WARRANTY INFORMATION CAUTION READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION. V1.0 - Published on 04.
Fanaway EVO2 Installation Instructions THANK YOU FOR PURCHASING Thank you for purchasing this quality Fanaway product. To ensure correct function and safety, please read and keep all instructions before using the product. SAFETY PRECAUTIONS Read and Save These Instructions This product conforms to UL standard 507. 1. WARNING -To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breaker of the fuse box to the outlet box. 2.
Fanaway EVO2 Installation Instructions PARTS LIST Unpack your ceiling fan and carefully identify the parts. Please refer to Fig 1. Fig.
Fanaway EVO2 Installation Instructions 1 Mounting bracket x 1 11 Lamp shade x 1 2 Canopy x 1 12 • Wood screw x 2 3 Down rod with ball joint x 1 • Machine screw x 2 4 Bolt and pin cover x 1 • Flat washer 5 Bolt x 1 • Spring washer x 2 6 Pin x 1 13 Wire nut x 6 7 Fan assembly x 1 14 Balance tape x 4 8 Lamp base x 1 15 Receiver 9 Light kit cover x 1 16 Remote 10 Screw for light kit cover x 3 17 LED bulb x 3 x2 x1 x 1 set INSTALLING THE MOUNTING BRACKET If there isn’t
Fanaway EVO2 Installation Instructions To hang your fan where there is an existing fixture but no ceiling joist, you may need an installation hanger bar (C) as shown in Fig.5. Make sure the hanger bar you purchase has been designed for use with ceiling fans. Fig. 5 INSTALLING THE FAN Installing the down rod 1) Feed the down rod (5) through the canopy (4) and the bolt and pin cover (6).
Fanaway EVO2 Installation Instructions HANGING THE FAN Pass the power supply wires (C) from the ceiling outlet box (B) through the center of the ceiling mounting bracket (D). Install the ceiling mounting bracket (D) on the outlet box (B) with the mounting screws (F) provided with the outlet box and washers (E) provided with fan. Fig. 7 Fig. 8 Fig. 7 Lift the fan assembly onto the mounting bracket.
Fanaway EVO2 Installation Instructions ELECTRICAL WIRING DIAGRAM WARNING: To avoid possible electrical shock, be sure you have turned off the power at the main circuit panel. Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape. Make sure there are no loose wire strands or connections. 1. Connect the household live supply wire (black) to receiver input wire (black, AC IN L) as shown in Fig. 10.
Fanaway EVO2 Installation Instructions FINISHING THE INSTALLATION Slide and align the canopy up to the mounting bracket. Ensure all electrical wiring is tucked inside the canopy and that the wires are not damaged during this step. Secure the canopy to the hanger bracket using the screws provided. Fig.
Fanaway EVO2 Installation Instructions INSTALLING THE REMOTE BATTERY 2 x AAA 1.5V (size) batteries are required to operate the remote control. Remove the battery cover from the back of the remote and insert 2 x AAA batteries. Ensure the polarities are correct as shown in the battery compartment. (Batteries included.) OPERATING THE REMOTE: Before you start using the remote, take the time to read through this section and get familiar with the buttons and function of each button.
Fanaway EVO2 Installation Instructions INSTALLING THE TRANSMITTER HOLDER Install the holder to the wall with two screws provided, hang up the transmitter by the holder. Fig. 16 AFTER INSTALLATION WOBBLE: NOTE: ceiling fans tend to move during operation due to the fact that they are mounted on a rubber grommet. If the fan was mounted rigidly to the ceiling it would cause excessive vibration. Movement of a few centimetres is quite acceptable and DOES NOT suggest any problem.
Fanaway EVO2 Installation Instructions CARE AND CLEANING: 1) Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to avoid scratching the paint finish. Please turn OFF electricity power when you do so. 2) Do not immerse your ceiling fan in the water. It could damage the motor or the blades and create the possibility of an electrical shock. 3) Ensure that the fitting does not come in contact with any organic solvents or cleaners.
Fanaway EVO2 Installation Instructions GRACIAS POR SU COMPRA Gracias por adquirir este producto de calidad Fanaway. Para garantizar un funcionamiento correcto y seguro, lea y respete todas las instrucciones antes de usar el producto. MEDIDAS DE SEGURIDAD Lea y guarde estas instrucciones Este producto cumple con la norma 507 de UL. 1. ADVERTENCIA - Para evitar posibles descargas eléctricas, corte la corriente que va a la caja eléctrica desde el disyuntor o la caja de fusibles. 2.
Fanaway EVO2 Installation Instructions 13 | P a g e 0003/10/XXX/01 LD-
Fanaway EVO2 Installation Instructions LISTA DE PIEZAS Desembale su ventilador de techo e identifique perfectamente sus componentes. Consulte la Fig. 1. Fig.
Fanaway EVO2 Installation Instructions 1 Soporte mural x 1 11 Pantalla de la lámpara x 1 2 Florón x 1 12 • Tornillo para madera x 2 3 Tija con junta esférica x 1 • Tornillo para metal x 2 4 Tapa de perno y pasador x 1 • Arandela plana x 2 5 Perno x 1 • Arandela de resorte x 2 6 Pasador x 1 13 Tuerca de alambre x 6 7 Unidad del ventilador x 1 14 Cinta de equilibrado x 4 8 Base de la lámpara x 1 15 Receptor x 1 9 Cubierta x 1 16 Mando a distancia x 1 set 10 Tornillos de l
Fanaway EVO2 Installation Instructions más larga para mantener el espacio necesario entre el extremo del aspa y el techo. NOTA: El ventilador de techo debe instalarse en un lugar donde los extremos de las aspas queden a 300 mm como mínimo de las paredes y otros objetos. NOTA: Para la instalación en techos inclinados, la abertura del soporte del ventilador (B) debe apuntar hacia el pico del techo.
Fanaway EVO2 Installation Instructions CÓMO COLGAR EL VENTILADOR Pase los cables de corriente (C) de la caja eléctrica del techo (B) por el centro del soporte mural del techo (D). Instale el soporte mural del techo (D) en la caja eléctrica (B) con los tornillos de montaje (F) incluidos con la caja eléctrica y las arandelas (E) incluidas con el ventilador. Fig. 7 Fig. 8 Fig. 7 Levante el conjunto del ventilador y móntelo en el soporte mural.
Fanaway EVO2 Installation Instructions DIAGRAMA DE CONEXIONES ELÉCTRICAS ADVERTENCIA: Para evitar posibles descargas eléctricas, asegúrese de que la corriente esté cortada en el cuadro de distribución. Siga los pasos siguientes para conectar el ventilador al cableado doméstico. Utilice las tuercas de conexión de alambre suministradas con su ventilador. Asegure los conectores con cinta aislante. Asegúrese de que no haya hilos de cable o conexiones sueltos. 1.
Fanaway EVO2 Installation Instructions CÓMO FINALIZAR LA INSTALACIÓN Deslice hacia arriba y alinee el florón con el soporte mural. Asegúrese de que todo el cableado eléctrico quede insertado dentro del florón y de que los cables no se dañen durante este paso. Fije el florón al soporte del colgador utilizando los tornillos suministrados. Fig.
Fanaway EVO2 Installation Instructions Fig. 12 Fig. 13 Fig. 13 Cambie la posición de los interruptores DIP en el transmisor remoto y el receptor. Asegúrese de que los interruptores DIP coincidan en el receptor remoto y en el transmisor. Si no coincidieran, el transmisor no funcionará. Fig. 13 INSTALLING THE REMOTE BATTERY 2 x AAA 1.5V (size) batteries are required to operate the remote control. Remove the battery cover from the back of the remote and insert 2 x AAA batteries.
Fanaway EVO2 Installation Instructions INTERRUPTOR D/ON : El interruptor con el símbolo D/ON controla la función de regulación de las luces. Si las bombillas utilizadas no son regulables, utilice un bolígrafo de punta de bola o un destornillador pequeño para ajustar el interruptor a «D» y deshabilitar la función de regulación de la luz. Si utiliza bombillas halógenas regulables, ajuste el interruptor a «ON» para habilitar la función de regulación de la luz. Fig. 15 Fig. 15 Fig.
Fanaway EVO2 Installation Instructions INSTALACIÓN DEL PORTAMANDO Instale el soporte en la pared con los dos tornillos suministrados y cuelgue el transmisor junto al soporte. Fig. 16 DESPUÉS DE LA INSTALACIÓN BAMBOLEO: NOTA: Los ventiladores de techo tienden a moverse cuando están funcionando debido a que están montados sobre una arandela de goma. Si el ventilador está montado rígidamente al techo, se podrían generar unas vibraciones excesivas.
Fanaway EVO2 Installation Instructions ruido del motor del ventilador. Esto es algo normal. Por favor, permita un período de rodaje de 24 horas, transcurridos los cuales la mayoría de los ruidos asociados con su nuevo ventilador deberían desaparecer. Todos los motores eléctricos son audibles hasta cierto punto. Entienda que esto no es un fallo del producto y, por lo tanto, no está cubierto por la garantía.