User Manual

RGB 500 Series • Specifications
RGB 500 Series • Specifications
Specifications, cont’d
A-3
Specifications
A-2
Max. rise/fall time ....................... 3.5 nS
Polarity
AKM models ....................... RGBHV...................... Polarity follows
input when RGBHV
is input and the sync
polarity switch is set
to Off. Sync polarity
is negative if the
sync polarity switch
is set to On.
RGBS, RGsB .............. Negative
All other models ............... RGBHV...................... Polarity follows
input when RGBHV
is input and the
bottom panel sync
polarity jumper is
set to follow (pin 1
jumpered to pin 2).
Sync polarity is
negative if the sync
polarity jumper is
set to negative (pin 2
jumpered to pin 3).
RGBS, RGsB .............. Negative
Audio
Gain................................................ Unbalanced 0dB, balanced +6dB
Frequency response .................... 20 Hz to 20 kHz, ±0.05dB
THD + Noise................................. 0.03% @1 kHz, 0.3% @ 20 kHz at rated
maximum output drive
S/N ................................................ >90dB at rated maximum output (14dBm),
balanced
Stereo channel separation .......... >95dB @ 1 kHz to 20 kHz
Audio input
Number/signal type ................... 1 PC level stereo, unbalanced
Connectors ................................... 1 3.5 mm stereo jack, 2 channel; tip (L),
ring (R), sleeve (ground)
Impedance .................................... 10 kohms, DC coupled
Maximum level ............................ +8.5dBu,(unbalanced) at stated %THD+N
Audio output
Number/signal type ................... 1 stereo (2 channel), balanced/unbalanced
Connectors ................................... 1 3.5 mm stereo captive screw connector,
5 pole, for left and right output
Video
Gain................................................ Unity (0.70V p-p), (0.725V p-p) 50%
peaking, (0.75V p-p) 100% peaking
Bandwidth..................................... 300 MHz (-3dB)
Video input
Number/signal type ................... 1 analog RGBHV, RGBS, RGsB, RsGsBs
Connectors
RGB 500, RGB 500 Dual, RGB 508, RGB 500 AKM
1 9-pin D male, MBC/LBC cable or buffer
RGB 560, RGB 560 Dual, RGB 568, RGB 560 AKM
1 15-pin HD female
Minimum/maximum levels....... Analog ....... 0.3V to 1.5V p-p with no
offset
Impedance .................................... 75 ohms or High Z, switchable (set to 75
ohms if no local monitor is connected)
Horizontal frequency.................. Autoscan 15 kHz to 130 kHz
Vertical frequency ....................... Autoscan 30 Hz to 120 Hz
Return loss .................................... -30dB @ 5 MHz
Maximum DC offset.................... 4.0V
Video output
Number/signal type ................... 1 analog RGBHV, RGBS, RGsB
Connectors
All models ........................ 5 BNC female
RGB 560, RGB 560 Dual, RGB 568, RGB 560 AKM
1 15-pin HD female for buffered local
monitor output
Minimum/maximum levels....... 0.70V to 0.75V p-p with no offset and 0.7V
p-p input
Impedance .................................... 75 ohms
Return loss .................................... -30dB @ 5 MHz
Sync
Input type ..................................... RGBHV TTL (±), RGBS TTL (-), RGsB 0.3V
(-), RsGsBs 1.3V (-)
Output type .................................. RGBHV (±), RGBS(-), RGsB (-)
Input level ..................................... 2V to 5.5V p-p with ±0.3VDC offset (max.)
Output level .................................. 4V to 5V p-p
Input impedance .......................... 10 kohms
Output impedance ....................... 75 ohms
Max. input voltage....................... 5.7V p-p
Max. propagation delay.............. 48 nS