Instructions / Assembly

ManualsBrandsEverpure ManualsKitchenEC210 Pre-Filter Under-Sink Water Filter Cartridge (20-Pack)

Installation and Operation Guide

E10 & E20 Prefilter Systems

E-Series prefilters are designed to increase the life of Everpure carbon water filters in

areas with an unusual amount of dirt in the water. With a 10 micron (nominal) rating,

the Everpure prefilter traps much of the dirt which contributes to scale buildup in ice

makers, and clogs the delicate orifices of other water-using equipment.

Parts List

Description Part No.

Head EV3112-37

O-Ring (E-Series) EV3112-40

EC110 Coarse Prefilter Cartridge 40 pk. EV9534-40

EC110 Coarse Prefilter Cartridge 12 pk. EV9534-12

EC210 Coarse Prefilter Cartridge 20 pk. EV9534-20

EC210 Coarse Prefilter Cartridge 6 pk. EV9534-26

10” Bowl, clear EV3112-39

20” Bowl, clear EV3112-38

10” Bowl, opaque EV3112-56

20” Bowl, opaque EV3112-55

Reducer Bushing for inlet and outlet ports EV3105-91

3/4” NPT x 3/8” FPT (E10)

Reducer Bushing for inlet and outlet ports EV3098-23

3/4” NPT x 1/2” FPT (E20)

Filter wrench EV3112-41

*The Standard EC110 Cartridge is provided with each Model E10 Filter. It is rated at 10

microns nominally and has a more-than-adequate life when filtering water with "normal" or

average dirt loads. The EC210 cartridge is provided with each E20 filter, which is also rated

at 10 microns nominally.

Applications and Features

• General purpose coarse filtration

• Pre-filtration for fine filters

• Reduces dirt, rust, oxidized iron and sulfide

• High-strength materials

Installation

The E10 coarse prefilter (part number EV9795-80) includes two 3/8" FPT optional reducer bushings. The E20 course pre-

filter (part number EV9795-90) includes two 1/2” FPT optional reducer bushings. Before starting the installation, be sure

to shut off both power and water to the equipment being served by your E-Series prefilter. For servicing purposes, a man-

ual shut-off valve should be installed in the water line.

IMPORTANT: Always use a NSF approved pipe dope or Teflon tape at all thread connections.

1. Select a suitable location for mounting the prefilter and install mounting screws 2 1/4" apart. The prefilter should be

close to the machine served and mounted ahead of the carbon filters for optimum performance.

2. Remove the prefilter from the carton and separate the bowl and head assembly. Set the bowl and cartridge aside. If

installing the EV9795-80 coarse filter, assemble (2) 3/8" FPT x 3/4" MPT bushings to the head (as needed). If

installing the EV9795-90 coarse filter, assemble (2) 3/4” MPT x 1/2” FPT bushings to the head (as needed). Be sure

to use a NSF approved pipe dope or teflon tape.

3. Check to be sure the o-ring on the bowl is sufficiently lubricated. If additional lubrication is needed, use only a high

quality food grade silicone lubricant.

E20 Prefilter

EV9795-90

E10 Prefilter

EV9795-80

Summary of content (4 pages)

PAGE 1
Installation and Operation Guide E10 & E20 Prefilter Systems E-Series prefilters are designed to increase the life of Everpure carbon water filters in areas with an unusual amount of dirt in the water. With a 10 micron (nominal) rating, the Everpure prefilter traps much of the dirt which contributes to scale buildup in ice makers, and clogs the delicate orifices of other water-using equipment. Parts List Description Part No. Head O-Ring (E-Series) EC110 Coarse Prefilter Cartridge 40 pk.
PAGE 2
4. Position the cartridge on the guide seat in the bottom of the bowl. Then screw the bowl onto the head, by hand; snug with filter wrench (EV3112-41) 5. Connect the water line to the inlet of the prefilter. (Use 3/8" minimum piping on Coarse prefilter EV9795-80, use 1/2” minimum piping on EV9795-90). Connect outlet side to the next piece of equipment used. 6.
PAGE 3
Limited Warranty Commercial Water Treatment Equipment You have just purchased one of the finest water treatment units made. As an expression of our confidence in Everpure products, this product is warranted against defects in material and workmanship to the original end-user when installed in accordance with Everpure specifications. The warranty period commences from the date of purchase and is administered as follows: For a period of ONE YEAR Replaceable elements (i.e.
PAGE 4
This page contains materials and DCO information. IT DOES NOT PRINT AS PART OF THE DOCUMENT! VENDOR MUST SUBMIT A MATERIAL CERTIFICATE OF COMPLIANCE WITH EACH SHIPMENT.