Installation Guide

ManualsBrandsEverbilt ManualsAppliancesDesigner Series 1/2 HP Continuous Feed Garbage Disposal with Brushed Nickel Sink Flange and Attached Power Cord

NOTE: This Garbage Disposal has been designed to operate on 110-120 Volt, 60 Hz

exclusively. Using any other voltage or Hz adversely affects performance.

IMPORTANT: Read all instructions thoroughly. Keep this guide for future reference.

CAUTION: Be sure to review SAFETY INSTRUCTIONS FIRST PERTAINING TO A RISK OF

FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS before using disposer.

Record important disposer information here

Model Number* Serial Number*

IMPORTANT SAFETY INSTRUCTIONS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK OR INJURY

TO PERSONS. SAVE THESE INSTRUCTIONS.

WARNING – When using electrical appliances,

basic precautions should always be followed,

including the following:

1. Read all instructions before using the appliance.

2. To reduce the risk of injury, close supervision is

necessary when an appliance is used near children.

3. Do not put fingers or hands into a waste disposer.

4. Turn the power switch to the off position before

attempting to clear a jam or remove an object from the

disposer.

5. When attempting to loosen a jam in a waste disposer,

use a long wooden object such as a wooden spoon or

the wooden handle of a broom or mop.

6. When attempting to remove objects from a waste

disposer use long-handled tongs or pliers. If the

disposer is magnetically actuated, non-magnetic tools

should be used.

7. To reduce the risk of injury by materials that may be

expelled by a waste disposer, do not put the following

into a disposer: clam or oyster shells; caustic drain

cleaners or similar products; glass, china or plastic;

large whole bones; metal, such as bottle caps, tin

cans, aluminum foil or utensils; hot grease or other

hot liquids; whole corn-husks.

8. When not operating a disposer, leave the stopper in

place to reduce the risk of objects falling into the

disposer.

9. DO NOT operate disposer unless splash guard is in

place.

10. For proper grounding instructions see the ELECTRICAL

CONNECTIONS portion of this manual.

The receptacle to which this appliance is

connected must be controlled by a switch.

*Above information appears on the label affixed to the bottom of the disposer. For your convenience,

write down the model and serial number prior to installation.

Proof of purchase is required for

Warranty. Staple receipt or proof of purchase to this manual for easy reference.

Warranty is non-transferable.

Instruction Manual

Having Problems? Don't go back to the store.

Call us toll-free at 1-833-240-6222 for assistance.

M-F 8:00am-5:00pm PST English & Spanish

GARBAGE DISPOSAL

Summary of content (9 pages)

PAGE 1
GARBAGE DISPOSAL Instruction Manual NOTE: This Garbage Disposal has been designed to operate on 110-120 Volt, 60 Hz exclusively. Using any other voltage or Hz adversely affects performance. IMPORTANT: Read all instructions thoroughly. Keep this guide for future reference. CAUTION: Be sure to review SAFETY INSTRUCTIONS FIRST PERTAINING TO A RISK OF FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS before using disposer.
PAGE 2
1. REMOVAL OF OLD UNIT TYPICAL INSTRUCTIONS, YOUR MODEL MAY VARY. Before starting this step, turn off electrical power at the circuit breaker or fuse box. Unplug disposer. NOTE: If your old mount is the same type (3-Bolt Mount) as the mount on your new disposer and you wish to continue using the old mount, just remove your old disposer as shown below in parts 1A,-1B, & 1C then skip to Step 3 on page 5.
PAGE 3
2. INSTALLATION OF MOUNTING ASSEMBLY READ CAREFULLY AND COMPLETELY BEFORE STARTING A STOPPER B REMOVABLE SPLASH GUARD NOTE: As the mounting assembly is properly assembled at the factory, please pay close attention to the order of the mounting system parts.
PAGE 4
(2. CONTINUED) INSTALLATION OF MOUNTING ASSEMBLY A. The Cushion Ring and the Lower Mount Ring will remain attached to the disposer during installation. Take apart the A1 other parts of the mounting assembly by rotating the Lower Mount Ring (J on page 3) clockwise until the Lower Mount Ring Tabs slide off from the Upper Mount Ring ramp (A1). This allows you to pull the Sink Flange up and out of the remaining Lower Mount Assembly. Note the order of these parts as they are arranged in the required order.
PAGE 5
3. DISHWASHER CONNECTION PREPARATION If you are utilizing a dishwasher, complete the following procedure. KNOCK OUT PLUG Using a blunt instrument (steel punch or wooden dowel), knock out entire plug. Do not use a screwdriver or sharp instrument. (When knockout plug falls into disposer, you may remove it or grind it up when the disposer is used. This will not damage the disposer in any way, but it may take some time to grind). WOOD OR METAL DOWEL 4.
PAGE 6
. DISCHARGE ELBOW & DISHWASHER CONNECTIONS A. Connect bottom of the elbow by tightening the slip nut (see 6A). If you are connecting to a dishwasher, see B. If not, make sure all plumbing connections are tight and in accordance with all plumbing codes and ordinances. Run water and check for leaks. B. Connect dishwasher hose (6B) using a hose clamp. Make sure all plumbing connections are tight and in accordance with all plumbing codes and ordinances. Run water and check for leaks.
PAGE 7
PERMANENT WIRE INSTALLATION INSTRUCTIONS (CONTINUED) 1. 2. 3. Turn off or disconnect all power to the wall junction box serving the disposer. Open the junction box in the wall and remove the wire nuts or electrical tape or whatever is tying the old disposer wire to the electrical wire inside of the junction box. Open the end bell plate at the bottom or the disposer. If you are using flexible armored (BX) cable: 1. Install cable fitting in the disposer end bell hole. 2.
PAGE 8
10. TROUBLESHOOTING Before seeking repair or replacement, we recommend that you review the following: LOUD NOISES: (Other than those during grinding of small bones and fruit pits): These are usually caused by accidental entry of a spoon, bottle cap or other foreign object. To correct this, turn off electrical switch and water. After disposer has stopped, remove splash guard, remove object with long handled tongs, and replace splash guard.
PAGE 9
WARRANTY Proof of purchase is required! Staple receipt or proof of purchase to this manual. Tracking is handled through the serial number affixed to the bottom of the disposer and/or on the power cord label. Conveniently record your model number and serial number on the front of this manual for your records. If you need warranty service, call us toll-free at 833-240-6222. Have serial number and receipt available for the technician. Warranty is non-transferable. 1.