INTRODUCTION Thank you for purchasing the ETON Car Power Amplifier. If, after reading your manual, you still have questions regarding this product, we recommend that you see your ETON dealer. The serial number can be found on the outside of the box. Please record it in the space provided below as your permanent record. This will serve as verification of your factory warranty and may become useful in recovering your amplifier if it is ever stolen.
DESIGN FEATURES A. Power Fuse: If the Fuse should blow, never replace with one of greater value than the original B. Power Connector terminals: Connects Power, Ground, and Remote. D. RCA Input Jacks - Line Level from Radio Pre-outs: The industry standard RCA jack provides an easy connection for signal level input. They are platinum to resist the signal degradation caused by corrosion. E. Level Control: This can be adjusted to match output levels from a variety of source units. F.
INSTALLATION INSTALLATION CONSIDERATIONS The following is a list of tools needed for installation: Volt/Ohm Meter Hand held drill w/assorted bits Wire strippers 1/8” diameter heat-shrink tubing Wire crimpers Assorted connectors Wire cutters Adequate Length-Power wire #2 Phillips screwdriver Adequate Length-Remote Turn-on Wire Battery post wrench Adequate Length-Grounding Wire This section focuses on some of the vehicle considerations for installing your new Amplifier.
INSTALLATION BATTERY AND CHARGING To maximize the performance of your amplifier, we suggest the use of a heavy duty battery and an energy storage capacitor. WIRING THE SYSTEM CAUTION: If you do not feel comfortable with wiring your new unit, please see your local Authorized ETON Dealer for installation. CAUTION: Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.
INSTALLATION NOTE: Mono amplifier speaker outputs (A & B) are wired in parallel internally.
O P E RAT I O N ADJUSTING LEVEL To adjust the level setting, turn the amplifier levels all the way down. Turn the source unit volume up until distortion is audible and then turn it down a bit until the distortion is inaudible This will be about two thirds all the way up on most source units Next, turn the amplifier level setting until once again distortion is audible and then back it down until the distortion is inaudible.
REMOTE LEVEL CONTROL (EC 1200.1D Only) Mounting and installation 1. Find a location, either under the dash or near the center console, that gives easy access to the remote. 2. Using the screws supplied, install the mounting clip with the tabs towards the back. 3. Route the cable for the remote and connect to both the remote and amplifier. 4. Slip the remote onto the mounting clip until it snaps into place. STRAPPING AMPLIFIERS (EC 1200.1D Only) CAUTION: Two EC 1200.
Model No. RMS power per channel Power @1Ω / channel EC 300.2A EC 500.4S ED 1200.1D N/A N/A 1135W x 1 Power @2Ω / channel 225W x2 115Wx2 + 230W x2 730W x1 Power @4Ω / channel Bridge RMS Power /channel Power @ 2Ω / channel Power @ 4Ω / channel Maximum current Signal to noise ratio THD Damping Factor Channel Separation Freq. Response (+/- 1.0 dB) Input sensitivity Fuses Input Connector Impedance LED Display RCA Input / Output Level control Slide Switch for HPF / Flat / LPF Variable Freq.
Einleitung Vielen Dank, dass Sie sich für eine ETON Endstufe entschieden haben. Bitte lesen Sie vor Gebrauch des Verstärkers die Bedienungsanleitung sorgfältig. Sie enthält viele Hinweise für den produktgerechten Umgang mit Ihrem Verstärker. Die Seriennummer finden Sie an der Außenseite der Verpackung. Bitte notieren Sie diese Nummer in dem dafür vorgesehenen Feld. Serien-Nummer: _______________________________________ Model-Nummer: _______________________________________ Inhalt Einleitung.
Designcharakteristiken A. Hauptsicherung: Sollte diese Sicherung auslösen, müssen Sie vor erneuern der Sicherung die Ursache feststellen. Kontaktieren Sie im Zweifelsfall Ihren Fachhändler. Erneuern Sie die Sicherung nie durch eine Sicherung mir höherer Amperezahl. B. Stromanschlüsse: Zum Anschluss der Plus- und Minus-Spannungsversorgung, sowie für die Einschaltspannung. D. Cinch-Eingangsbuchsen: Signaleingang von den Vorverstärkerausgängen des Radios oder anderer Signalquellen, wie z.B. DVD –Spieler, usw.
EINBAU Dieser Abschnitt konzentriert sich auf Erwägungen hinsichtlich des Einbaus Ihres neuen Verstärkers im Fahrzeug. Vorausplanung Ihres Systemlayouts und der besten Verkabelungsrouten spart Zeit beim Einbau. Prüfen Sie bei der Wahl eines Layouts für Ihr neues System, ob alle Komponenten leicht erreichbar sind, um Einstellungen vorzunehmen. VORSICHT: Sollten Sie nicht sicher sein den Verstärke richtig zu installieren, dann wenden Sie sich bitte an Ihren Fachhändler.
EINBAU BATTERIE UND AUFLADUNG Verstärker belasten Batterie- und Ladesysteme zusätzlich. Prüfen Sie deshalb Batterie und Lichtmaschine auf deren Kapazität um Ihren Verstärker sicher betreiben zu können. Um die Leistung Ihres Verstärkers ausnutzen zu können, empfehlen wir die Verwendung von hochbelastbaren Batterien, sowie einen zusätzlichen Kondensator. VERKABELUNG DES SYSTEMS VORSICHT: Sollten Sie nicht sicher sein den Verstärker richtig zu installieren, dann wenden Sie sich bitte an Ihren Fachhändler.
EINBAU HINWEIS: Monoverstärkerlautsprecherausgänge (A u. B) sind parallel angeschlossen.
BETRIEB LAUTSTÄRKE (LEVEL) EINSTELLEN Drehen Sie den Levelregler auf die niedrigste Verstärkung. Drehen sie danach die Lautstärke Ihres Zweikanal - überbrückt Steuergerätes solange hoch, bis erste Verzerrungen hörbar sind. Drehen Sie nun den Levelregler so weit auf, bis wiederum erste leichte Verzerrungen hörbar sind und drehen ihn dann zurück, bis keine Verzerrungen mehr hörbar sind. HINWEIS: Detailliertere Informationen zum Einstellungsverfahren erhalten Sie vom ETON Fachhändler.
EINBAU Externe Lautstärkeregler (nur im LP-Tiefpassmodus verwendbar) (Nur bei Modell EC 1200.1 D) Einbau und Installation 1. Eine Stelle unter dem Armaturenbrett oder nahe wählen, die leichten Zugriff auf erlaubt. der Mittelkonsole die Fernbedienung 2. Mit den beiliegenden Schrauben die Befestigungsklemme mit den Spitzen nach hinten einbauen. 3. Das Kabel für die Fernbedienung verlegen und Fernbedienung, als auch am anschließen. sowohl an der Verstärker 4.
Model No. Ausgangsleitstung (RMS) Stereo 1 Ohm Stereo 2 Ohm Stereo 4 Ohm Gebrückt (bridged) Power @ 2Ω / channel Power @ 4Ω / channel Maximale Strohmaufnahme Signal Rauschabstand THD Dämpfungsfaktor Kanalabstand Frequenzgang (+/- 1.0 dB) Eingangsempfindlichkeit Schutzschaltung Eingang Stecker Impedanz LED Display RCA Input / Output Level control Umschalter für HPF / Flat /LPF Variable Freq. Kontrolle: HPF /LPF Frequenzgang Flankensteilheit 7.0 Subsonic Filter: Frequenzgang Flankensteilheit EC 300.