Table gaz ETG54i
TABLE DES MATIÈRES Informations de sécurité Consignes de sécurité Installation Description de l'appareil Utilisation quotidienne 2 4 7 12 12 Conseils Entretien et nettoyage En cas d'anomalie de fonctionnement Caractéristiques techniques Rendement énergétique 13 14 16 17 18 Sous réserve de modifications. INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies.
Sécurité générale • • • • • • • • • • • AVERTISSEMENT : L'appareil et ses parties accessibles deviennent chauds pendant son fonctionnement. Veillez à ne pas toucher les éléments chauffants. Les enfants de moins de 8 ans doivent être tenus à l'écart, à moins d'être surveillés en permanence. Ne faites pas fonctionner l'appareil avec un minuteur externe ou un système de commande à distance.
• AVERTISSEMENT : Utilisez uniquement les dispositifs de protection pour table de cuisson conçus ou indiqués comme adaptés par le fabricant de l'appareil de cuisson dans les instructions d'utilisation, ou les dispositifs de protection pour table de cuisson intégrés à l'appareil. L'utilisation de dispositifs de protection non adaptés peut entraîner des accidents. CONSIGNES DE SÉCURITÉ suffisamment d'espace entre le fond de l'appareil et le tiroir supérieur pour que l'air puisse circuler.
• • • • • • • • • surfaces brûlantes de l'appareil ou les récipients brûlants lorsque vous branchez l'appareil à des prises électriques situées à proximité. N'utilisez pas d'adaptateurs multiprises ni de rallonges. Veillez à ne pas endommager la fiche secteur (si présente) ni le câble d'alimentation. Contactez notre service après-vente agréé ou un électricien pour remplacer le câble d'alimentation s'il est endommagé.
• Les graisses et l'huile chaudes peuvent dégager des vapeurs inflammables. Tenez les flammes ou les objets chauds éloignés des graisses et de l'huile lorsque vous vous en servez pour cuisiner. • Les vapeurs dégagées par l'huile très chaude peuvent provoquer une combustion spontanée. • L'huile qui a servi contient des restes d'aliments pouvant provoquer un incendie à température plus faible que l'huile n'ayant jamais servi.
Mise au rebut • Coupez le câble d'alimentation au ras de l'appareil et mettez-le au rebut. • Aplatissez les tuyaux de gaz externes. AVERTISSEMENT! Risque de blessure ou d'asphyxie. Maintenance • Contactez votre service municipal pour obtenir des informations sur la marche à suivre pour mettre l'appareil au rebut. • Débranchez l'appareil de l'alimentation électrique. • Pour réparer l'appareil, contactez un service après-vente agréé. • Utilisez exclusivement des pièces d'origine.
Remplacement des injecteurs l'appareil ne fonctionne qu'au butane. Si l'appareil fonctionne au propane, utilisez un tuyau flexible avec un embout métallique approprié. Raccordement avec des tuyaux flexibles non métalliques : Si le raccordement peut être facilement contrôlé dans son ensemble, vous pouvez utiliser un tuyau flexible. Fixez fermement le tuyau flexible à l'aide de colliers. 1. Démontez les supports des casseroles. 2. Démontez les chapeaux et les couronnes du brûleur. 3.
A • • • 5. Si vous passez : • du gaz naturel G20/G25 20/25 mbar au gaz liquéfié, serrez entièrement la vis de réglage. • du gaz liquéfié au gaz naturel G20/G25 20/25 mbar, dévissez la vis de réglage d'environ 1/4 de tour (1/2 tour pour un brûleur multicouronne). 6. Réinstallez le joint et la manette. • • être adaptée au câble d'alimentation. Assurez-vous que la fiche est branchée dans une prise correcte. Utilisez toujours une prise de courant de sécurité correctement installée.
Montage 5. 1. 6. 2. 7. 3. min. 450 mm 8. min. 650 mm min. 55 mm A 30 mm 480 mm 560 mm 4.
9. A B min 30 mm min 5 mm (max 150 mm) 60 mm A. Panneau amovible B. Espace pour les branchements 10. Élément de cuisine avec four Les branchements électriques de la table de cuisson et du four doivent être installés séparément pour des raisons de sécurité et pour permettre un retrait facile du four de l'ensemble. ATTENTION! Installez l'appareil uniquement sur un plan de travail dont la surface est plane.
DESCRIPTION DE L'APPAREIL Description de la table de cuisson 1 1 2 3 4 5 2 3 Brûleur multi-couronne Brûleur rapide Brûleur semi-rapide Brûleur auxiliaire Manettes de commande 4 5 Manette de commande Symbole Symbole Description Description alimentation en gaz mini‐ male pas d'alimentation en gaz / position Arrêt position d'allumage / ali‐ mentation en gaz maxi‐ male UTILISATION QUOTIDIENNE AVERTISSEMENT! Reportezvous aux chapitres concernant la sécurité.
Allumage du brûleur ATTENTION! En cas de coupure d'électricité, vous pouvez allumer le brûleur sans dispositif électrique : pour cela, approchez une flamme du brûleur, tournez la manette vers la gauche jusqu'à la position d'arrivée de gaz maximale et enfoncez-la. Maintenez la manette de commande enfoncée pendant environ 10 secondes pour permettre au thermocouple de chauffer. Allumez toujours le brûleur avant de poser un récipient dessus.
Ustensiles de cuisson ATTENTION! Assurez-vous que les récipients de cuisson sont bien centrés sur le brûleur afin de garantir leur stabilité et de réduire la consommation de gaz. ATTENTION! N'utilisez pas de plats en fonte, en stéatite, en grès, de grils ou de plats à gratin. L'acier inoxydable peut ternir s'il est trop chauffé. Diamètres des récipients AVERTISSEMENT! Ne placez pas le même récipient sur deux brûleurs.
Supports de casserole Les supports de casserole ne sont pas adaptés au lavage dans un lave-vaisselle. Ils doivent être lavés à la main. 1. Retirez les supports de casserole pour nettoyer facilement la table de cuisson. Replacez les supports de casserole avec soin afin de ne pas endommager le dessus de la table de cuisson. 2. Lorsque vous lavez les supports de casserole à la main, faites bien attention lorsque vous les essuyez, car le revêtement en émail peut présenter des bords coupants.
Entretien périodique d'arrivée de gaz et du régulateur de pression si votre installation en est équipée. Contactez périodiquement votre service après-vente pour contrôler l'état du tuyau EN CAS D'ANOMALIE DE FONCTIONNEMENT AVERTISSEMENT! Reportezvous aux chapitres concernant la sécurité. En cas d'anomalie de fonctionnement Problème Cause probable Solution Il n'y a aucune étincelle lors‐ que vous essayez d'activer le générateur d'étincelle.
Étiquettes fournies dans le sachet des accessoires Collez les étiquettes adhésives comme indiqué ci-dessous : A B MOD. MOD. PROD.NO. PROD.NO. SER.NO SER.NO DATA DATA C 0049 MOD. PROD.NO. SER.NO. TYPE IP20 03 IT MADE IN ITALY A. Collez-la sur la carte de garantie et envoyez cette partie (le cas échéant). B. Collez-la sur la carte de garantie et conservez cette partie (le cas échéant). C. Collez-la sur la notice d'utilisation.
Autres caractéristiques techniques PUISSANCE TOTA‐ LE : Gaz d'origine : G20/G25 (2E+) 20/25 mbar = 11,7 kW Gaz de remplace‐ ment : G30 (3+) 28-30 mbar = 832 g/h G31 (3+) 37 mbar = 818 g/h Alimentation électri‐ que : 220-240 V ~ 50/60 Hz Catégorie de l'appa‐ reil : II2E+3+ Raccordement au gaz : G 1/2" Classe de l'appareil : 3 Brûleurs à gaz pour GAZ NATUREL G20/G25 20/25 mbar BRÛLEUR PUISSANCE NOR‐ MALE kW Multi couronne PUISSANCE MINI‐ MALE kW CARACTÉRISTIQUE DE L'INJECTEUR 4,0 1,4 146
Type de table de cuisson Table de cuisson intégrée Nombre de brûleurs à gaz 5 Efficacité énergétique selon le brû‐ leur à gaz (EE gas burner) Milieu gauche - Multi couronne 54.4% Arrière central - Semi-rapide 56.1% Arrière droit - Rapide 55.2% Avant central - Semi-rapide 57.7% Avant droit - Auxiliaire non applicable Efficacité énergétique de la table de cuisson (EE gas hob) 55.
*
867345865-A-452018 ETG54i Art. 8003029; CE0476 Réf.