User's Guide LX Wallmount System 7 - 25 lbs* (2.3 - 11.3 kg) 2" - 8" * The lower most range of motion for vertical lift is decreased up to 4.5” (114 mm) when arm is adjusted to hold over 20lbs (9 kgs). (102 - 203 mm) 40 lbs (18 kg) 8.5” (216 mm) < 4.5” (114 mm) 0 - 5 lbs (0 - 2.3 kg) Includes Constant Force™ Technology 180° 360° 80° 13" (330 mm) 180° 180° 5° 360° 13" (330 mm) 180° 3° 5° 3° 90° English For the latest User Installation Guide please visit: www.ergotron.
Components A 1 C B 1x D 14x 1x 2x 14x 2x 2x 2 2x 3 1x 1x 2x 7x 4x 1x 3x 4 1/4-20 x 2" 4x M4 x 8mm 1x 5 2x 2x 1x 1/4-20 x 1/2" 1x 8x 2x 10-24 x 1/2" 2x 6 7x 9x 12x 2x 1x 2.5mm 1x 1/8” M10 x 16mm 4x 7 4x M4 x 10mm 6mm 4x 1x 2x 8 1x M4 x 10mm 4x 9 4mm 1x 4x 2x 4x 1x M4.2 x 25mm M3 x 6mm 1x 1x 1x 2x 10 1x 2x 1x M4 x 14mm Tools Needed 7mm 7/16" Ø 1/2” (12.
1 Mounting Height for Ergonomic Workstation This mounting height is a recommendation for an ergonomic workstation that accommodates user heights of 5'0"-6'1" (152-185cm) when set up for standing and user heights of 5’0”-6’4” (152-193cm) when set up for sitting. If user heights are different than this, you should change mounting height to accommodate user heights. (Change mounting height one inch for every one inch difference in user heights).
2 WARNING: Ensure that the wall structure is capable of supporting four times the total weight of mounted equipment. Mounting to wall surfaces that do not meet this criteria may result in an unstable, unsafe condition which could lead to personal injury and/or property damage. Consult a construction professional if you have any doubt about what this means in regard to your particular application. CAUTION: Make sure the wall mount bracket is level, flush and snug to the wall surface.
Wood Madera Bois Solide Holzbalkenträger Massief Houten Pilaren Due montanti in legno massiccio 木 木质 나무 Studs ≥ 25 gauge steel Pernos de acero de calibre ≥ 25 Goujons ≥ calibre 25 en acier Bolzen ≥ Blechlehre Nr.
Hollow Wall Pared Mur Wand Muur Parete 壁 墙壁 Requires minimum material thickness of 5/8” (16 mm). Requiere un grosor mínimo de 16 mm. Epaisseur minimum de 16 mm. Requer uma espessura mínima de 5/8” (16 mm). Mit einer Materialdicke von mindestens 16 mm. Vereist een minimale materiaaldikte van 1.6 cm. Richiede uno spessore del materiale non inferiore a 16 mm.
3 a b c 8x 1/4-20 x 1/2" 4x 10-24 x 1/2" 8x 10-24 x 1/2" 4x 10-24 x 1/2" NOTE: Fasteners may unwind due to vibration caused by movement of mounting solution over time. Inspect mounting solution for loose fasteners on a routine basis. If desired, apply a light duty thread locking adhesive to fasteners before installation to prevent back-out. d 888-45-184-W-05 rev.
4a b c 1x d 2x M10 x 16mm 1/8" 6mm e 12x Security Feature Función de seguridad Fonction de sécurité Sicherheitsmerkmal Beveiligingsfunctie Dispositivo antifurto セキュリティ機能 安全特性 8 of 17 f 2x g 1x 2" - 4" 4" - 8" (51 - 102 mm) (102 - 203 mm) 2x 7/16" 888-45-184-W-05 rev.
5 4x M4 x 10mm 4x M4 x 10mm M3 x 6mm 0° 6 a b 888-45-184-W-05 rev.
7 1x 4x M4 x 8mm 8 b a d e c f g 4x h i j k 10 of 17 888-45-184-W-05 rev.
9 4x 888-45-184-W-05 rev.
10 NOTE: Leave enough slack in cable to allow full range of motion. Caution: To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow these instructions may result in equipment damage or personal injury. 12 of 17 888-45-184-W-05 rev.
11 a Ø 7/32" (5.6 mm) b 1 b c d 2 e f M4.2 x 25mm 12 a 3 Flush with drywal M4.2 x 25mm b d e c 888-45-184-W-05 rev.
13 Adjustment Step Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
b Tilt – Forward and Backward 4mm Increase Friction If this product moves too easily, then you'll need to increase friction: Decrease Friction If this product is too difficult to move, then you'll need to decrease friction: CAUTION: DO NOT remove screw. Removing screw may cause damage to equipment. c Arm Swing – Side-to-side 2.
How to remove this tilting feature: 3° 3° Save these screws incase you want to add this feature later. 2x M4 x 14mm 16 of 17 888-45-184-W-05 rev.
Set Your Workstation to Work For YOU! Learn more about ergonomic computer use at: www.computingcomfort.org Height Position top of screen slightly below eye level. Position keyboard at about elbow height with wrists flat. Distance Position screen an arm's length from face—at least 20” (508mm). Position keyboard close enough to create a 90˚ angle in elbow. Angle Tilt screen to eliminate glare. Tilt the keyboard back 10° so that your wrists remain flat.