APPENDIX ESPAÑOL FRANÇAIS ENGLISH LCD Projector User Manual X200 MODEL LVP-X200A 1
CAUTION ENGLISH RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
Contents Important safeguards ...........................................................................4 Overview of the projector ......................................................................6 Overview of the remote control ............................................................8 Battery installation ............................................................................................. 9 ENGLISH Preparing the projector for operation ...............................................
ENGLISH Important safeguards PLEASE READ ALL THESE INSTRUCTIONS REGARDING YOUR LCD PROJECTOR AND RETAIN THEM FOR FUTURE REFERENCE. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE LCD PROJECTOR. 10. Power sources This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your office, consult your appliance dealer or local power company. 1.
Do not operate if smoke, strange noise or odor comes out of your projector. It might cause fire or electric shock. In this case, unplug immediately and contact your dealer. Never remove the cabinet. This projector contains high voltage circuitry. An inadvertent contact may result in an electric shock. Except as specifically explained in the Owner's Guide, do not attempt to service this product yourself. Please contact your dealer when you want to fix, adjust or inspect the projector.
Overview of the projector lamp lid Caution: Do not replace the lamp right after using the projector. The lamp is very hot. Switch the projector to stand-by mode, wait at least 120 seconds for the lamp and LCD panel to cool. Then turn off the main power switch, unplug from the outlet and wait for another one hour or until the lamp is cool to the touch. See page 40. exhaust slits ENGLISH handle Hold here to carry this projector.
PC card eject Press to eject the PC card. See page 27. INPUT1 RGB1 IN AUDIO MAIN INPUT2 AUDIO O I L RGB2 IN R AC IN VIDEO RGB OUT S-VIDEO RS-232C 1 PC card insert slot This is where you insert the PC card. See page 27. RS-232C 2 LINE-OUT RGB1 IN AUDIO AUDIO O MAIN power I L RGB2 IN ENGLISH PC audio input (stereo mini jack) Use to input PC audio signals. See pages 13 - 15. video/audio input Use to input video and audio. See page 12.
Overview of the remote control operation indicator When the operation button is pressed, this indicator blinks. It also illuminates when the projector is in the personal computer mode or drawing mode which is able to have a cursor operation. See pages 25, 38. cancel select This operates in the same way as the right button on the computer mouse. If this button is pressed during drawing mode, the figure will diappear. See pages 25, 38.
Important: • To save battery power, turn off the operation indicator by pressing the START/STOP button when not in use. • To save battery power, the operation indicator will turn off if the remote control is not operated for a period of 5 minutes. Battery installation ENGLISH Use two AA size batteries. 1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the arrow. 2.
Preparing the projector for operation ENGLISH Orientation of the projector Picture size can be set by changing the distance between the screen and the projector. Front projection To find the approximate distance screen between the projector and screen: Multiply the width of the screen x 1.875 ~ 1.975 (max.) , Multiply the width of the screen x 2.468 ~ 2.57 (min.) , • Refer to the chart to recommended distances in maximum H (height) zoom and minimum zoom.
Adjusting the angle of projection Getting ready for projection Screen on a flat wall with a 90 degree angle to the floor by adjusting two foot adjustments on the bottom of the projector. If the angle cannot be corrected by them, adjust the height and angle of screen. 1. Connect the power cord provided to this projector with the power jack of the projector. 2. Connect the power cord to the wall outlet. ground terminal screen foot adjustment 1. Lift the projector to the right angle. 2.
Basic connections This projector can be connected to equipment such as VCRs, video cameras, videodisc players, and personal computers having analog RGB input. Projector + AV equipment Make sure that your equipment is turned off before connection. Important: S-video signals take priority over video signals. If you input both S-video signals and normal video signals at the same time, the normal video input automatically shuts off.
Projector + IBM PC or IBM PC compatibles Make sure that your equipment is turned off before connection. ENGLISH Important: • Connectors or analog RGB output adapters may be necessary depending on the personal computer connected to this projector. Please contact your dealer. • The audio input for a personal computer is the stereo mini-jack. There are some personal computers that have different types of audio outputs or none at all. Please ask your dealer for details.
Basic connections (continue) Projector + Macintosh Important: • A monitor output adapter is necessary for a Macintosh if it has no video port. Contact your dealer. • If you use the RGB conversion adapter provided, set the dip switch to the appropriate position. See page 12. • Connectors or analog RGB output adapters may be necessary depending on the personal computer connected to this projector. Please contact your dealer. • The audio input for a personal computer is the stereo mini jack.
Projector + NEC PC-98 series Make sure that your equipment is turned off before connection. ENGLISH Important: • Connectors or analog RGB output adapters may be necessary depending on the personal computer connected to this projector. Please contact your dealer. • The audio input for a personal computer is the stereo mini jack. There are some personal computers that have different type or no audio outputs. Please ask your dealer for details.
To operate projector power ON Numbers 1 - 9 correspond to the instruction numbers below. 2, 9 Left side ENGLISH INPUT1 RGB1 IN AUDIO MAIN INPUT2 AUDIO O I L RGB2 IN R AC IN VIDEO RGB OUT S-VIDEO RS-232C 1 RS-232C 2 LINE -OUT LAMP TEMP CARD 1 RGB VIDEO CARD MENU CARD 2 FOCUS AUTO /ZOOM POSITION FINE ENTER 3, 7, 8 4 4 1. Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red. 2. Turn on the equipment connected to the projector. 3.
5. Press the FOCUS/ZOOM button to FOCUS. “FOCUS” will appear on the display. 6. Adjust with the ª or º buttons on the control panel (or { or } buttons on the remote control) to get a fine picture. • Focus and zoom adjustment by using the buttons on the control panel or the remote control is possible in the normal picture mode only. In PinP, EXPAND or cursor operation mode, the adjustment is impossible. Caution: • When you have finished using this equipment, wait 120 seconds for the exhaust fans to stop.
Menu operation Basic operation Several settings can be adjusted using Menu. EXAMPLE: Brightness adjustment 7. Press the or buttons on the control panel (or $ or % buttons on the remote control) to select the desired color R, G or B. ENGLISH 1. Press the MENU button. SIGNAL PinP/ EXPAND PICTURE PC CARD AUTO PLAY AUDIO BRIGHTNESS 2. Press the or buttons on the control panel (or $ or % buttons on the remote control) to select PICTURE.
MENU SIGNAL PinP/ EXPAND PICTURE or or Q PC CARD AUTO PLAY or W AUDIO or E R INSTALLATION OPTION or or Y T Ver. or U or I AUTO HORIZ. POSITION VERT. POSITION FINE SYNC. TRACKING RGB/Y,CB,CR AUTO SXGA70a 0 0 0 0 Y,CB,CR USER RGB ENTER /STILL MEMORIZE USER1 ENGLISH Q SIGNAL Qa DELETE USER2 SIGNAL RESET PinP/ EXPAND PICTURE PC CARD AUTO PLAY AUDIO INSTALLATION OPTION Ver. AUTO .................. Use to select AUTO, USER 1 or USER 2. HORIZ. POSITION ....
Menu operation (continue) E PinP/EXPAND This menu appears when either the display enlargement or PinP functions are used. ZOOM MODE 1 ON 2 2 2 OFF 3 3 4 ENGLISH PICTURE AUTO PIP SIZE 1 3 SIGNAL POSITION 1 PinP/ EXPAND 4 5 PC CARD AUTO PLAY AUDIO INSTALLATION OPTION Ver. ZOOM MODE ..... Selects the desired type of expand mode, type1, 2, 3 or 4 (Actual size display). POSITION .......... Selects the desired position of the sub image in expand or PinP mode. SIZE ....................
U OPTION SQUEEZE MENU POSITION AUTO POWER OFF REMOTE POSITION VIDEO SIGNAL MOTION ON STILL OFF 1 ON 2 OFF 5 min. FRONT SIGNAL PICTURE PC CARD AUTO PLAY AUDIO LANGUAGE NTSC AUTO PAL RGB1 Español SECAM RGB2 Deutsch English 4.43NTSC Français PAL-M Italiano REAR PinP/ EXPAND RGB OUTPUT AUTO AUTO INSTALLATION PAL-N OPTION Ver. MOTION/STILL . Select MOTION when motion images are mainly projected. Select STILL when still images such as PC-CARD images are mainly projected.
Picture adjustment Adjustment from personal computer ENGLISH Although this projector sets proper signal systems automatically for the image signal from personal computers, it cannot be applied to some of personal computers. In this case, press AUTO POSITION button. If the images are still not projected correctly, use MENU display to adjust the projected images from personal computers. Also available to memorize the setting.
Signal mode TV60 TV50 HiVision PC98 CGA70 CGA84 CGA85 VGA60 VGA72 VGA75 VGA85 SVGA56 SVGA60 SVGA72 SVGA75 SVGA85 XGA43i XGA60 XGA70 XGA75 XGA85 SXGA70a SXGA75a SXGA85a SXGA60a SXGA75a SXGA43i SXGA60 SXGA75 SXGA85 UXGA48i UXGA60 UXGA65 UXGA70 UXGA75 UXGA80 UXGA85 MAC13 MAC16 MAC19 MAC21 HP75 HP72 SUN66a SUN76a SUN66 SUN76 SGI72 SGI76 IBM60 resolution (H x V) – – – 640 x 400 640 x 400 640 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024
Picture adjustment (continue) GAMMA CORRECTION menu The proportion of the brightness of input signals to that of output signals can be corrected effectively by adjusting GAMMA. 1. Select GAMMA CORRECTION of PICTURE menu and then press the ENTER button. (The GAMMA CORRECTION menu appears on-screen display.) ENGLISH GAMMA CORRECTION - USER MASTER R G B 0 10 20 30 40 50 60 70 80 90 100 RETURN If you wish to change the color balance, follow the steps below. 6.
Advanced feature for presentation Cursor operation To draw line or frame 1. Press the CURSOR button. The cursor appears on the screen. 2. Press the START/STOP button to ON. The operation indicator will be illuminated. (The operation indicator will turn off if the remote control is not used for a period of five minutes.) 3. Move the cursor by using the remote control. Move to left 2. Press the START/STOP button to ON. The operation indicator will be illuminated. 3. Press the DOUBLE CLICK button.
Advanced feature for presentation (Continue) Super impose (Picture in Picture) Expand One of the special features of this unit is the picturein-picture (PinP) mode. PinP allows you to view different sources at the same time. The sub image will become a still picture. By pressing the EXPAND button on the remote control, you can view the detailed image of the picture. ENGLISH 1. Press the PinP button on the remote control. • Pressing the PinP button repeatedly will select on and off. 2.
PC-CARD The projector can play back an image by using the PCCARD. Play back 1. Insert the prerecorded PC-card. Using the PC-CARD Use only the flash memory card of PCMCIA•ATA compatible type II. • Due to PC-CARD type, some images can not be properly recorded. Please contact your dealer. 2. Press the CARD button repeatedly until PC-1 (or PC-2) appear on the screen. 2. Open PC-CARD cover on the left side of the projector. 3. Make sure the PC card is going to be inserted in right side.
PC-CARD (Continue) To automatically change the image, follow the steps as shown below. 1. Press the MENU button. SIGNAL ENGLISH 2. Press the PICTURE or PinP/ EXPAND PC CARD AUTO PLAY buttons on the control panel (or $ or % buttons on the remote control) to select PC CARD AUTO PLAY. SIGNAL PICTURE PinP/ EXPAND PC CARD AUTO PLAY 3. Press the ª or º buttons on the control panel (or { or } buttons on the remote control). AUTO SLIDE TIME 33 sec. SIGNAL 4.
Advanced feature with PC There are three types of application software provided. 1. PCV (PC Card Viewer) 2. PCGC (Personal Computer Graphic Controller) 3. SpacePointer (Driver for PC control by the remote controller) A. Environment Installation of software The following system software and hardware are necessary to use the projector. For Windows 95 or Windows NT 1. Start up Windows.
Advanced feature with PC (Continue) Starting up PCV (For Windows) For Windows 95 or Windows NT 1. Start up Windows. 2. Insert the PC card to the PC Card slot on the personal computer. ENGLISH 3. Start up Program Manager. Click the [Start] button and select the [Program (P)]➔[Pcv]➔[PCV]command. For Windows 3.1 1. Start up Windows. 2. Insert the PC card to the PC Card slot on the personal computer. 3. Double click the [PCV] icon in the PCV folder.
Recording the image (For Windows) When you wish to record the image of the display to a PC-CARD. 9. Click the return button. The presentation window will open. The recorded image appears on the presentation window. Drive bar • If you are using Windows 3.1, select ‘Select card drive‘ in Option menu of PCV main wimdow. 2. Choose [New presentation...] under the [File] menu. The new presentation window will open. 3. Choose [Add image] under the [Image] menu and then choose [Screen capture...].
Advanced feature with PC (Continue) Editing the presentation (For Windows) Delete the image 1. Select the image to be deleted. Preview an image 1. Double click the image. The preview image appears on the displays. ENGLISH 2. Choose [Delete image...] under the [File] menu. • If you are using Windows 3.1, choose [Delete image] under the [Option] menu. Sequencing A. Exchange images You can exchange the images among images next to each other. 1. Select an image to be exchanged. 2.
4. Click the properties button. Starting up PCV (For Macintosh) 1. Start up Macintosh. 2. Insert the PC card to the PC Card slot on the personal computer. 5. If necessary, set the Resolution, Expand, File Format or JPEG Quality. 6. Click OK button on the PCV driver Properties dialog box. 7. Click OK button. 8. Cooose the PC-CARD drive. 9. Click OK button. • The presentation data will be saved as PCVdrv on PC card. • PCVdrv is a temporaly file.
Advanced feature with PC (Continue) When you wish to record the image from existing files. 1. Choose [Create New presentation...] under the [File] menu. The new presentation window will open. 2. Choose [Open image file] under the [File] menu. ENGLISH 3. Select the image you wish to record. B. Move images You can move images to another position. 1. Select an image to be moved. 2. Drag the image and drop it on the other image (except next or previous image).
B. PCGC (Personal Computer Graphic Control) By connecting to personal computer is RS-232C port, you can operate your computer with the projector remote control. Also you can set the menu setting of the projector by computer. Connection ENGLISH Projector + IBM PC or IBM PC compatibles (DOS/V) to RS-232C 1 IN terminal to Com1 Comport Note: RS-232C cable If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required.
Advanced feature with PC (Continue) Installation of software Starting up PCGC For Windows 95 1. Start up Windows. Double click the [PCGC] icon in the setup folder to start up PCGC. 2. Insert the Projector driver CD-ROM into your CDROM drive. • Do not use SpacePointer during the PCGC operation. ENGLISH 3. Start up Program Manager. Click the [Start] button and select the [Run (R)] command. Then the [Run] dialog box is displayed. 4.
C. SpacePointer The remote control provides remote PC operation for presentation from PC. Connection Projector + IBM PC or IBM PC compatibles (DOS/V) RS-232Ccable(option) RS-232C adapter for Macintosh to Com1 Comport to RS-232C 2 terminal to RS-232C 1 terminal to Com1 Comport Note: ENGLISH When connecting two personal computers RS-232C cable If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required.
Advanced feature with PC (Continue) Installation of software Operation of PC by remote control For Windows 95 1. Start up Windows. The remote control provides remote PC operation for presentation from PC. 1. Press the RGB button to select RGB1 or RGB2. 2. Insert the Projector driver CD-ROM into your CDROM drive. ENGLISH 3. Start up Program Manager. Click the [Start] button and select the [Run (R)] command. Then the [Run] dialog box is displayed. 4.
Uninstallation of software For Windows 95 1. Start up Windows. 2. Insert the Projector driver CD-ROM into your CDROM drive. ENGLISH 3. Start up Program Manager. Click the [Start] button and select the [Run (R)] command. Then the [Run] dialog box is displayed. 4. If you inserted the CD-ROM to drive D, type [D: Win95\Sp\Spuninst] in the "command line" text box and click the "OK" button. The letter [D] may be different according to the drive you use. 5.
Replacement of a light source lamp ENGLISH The light source lamp is designed to project the image on the LCD panel. When the light source lamp no longer functions, replace it with a new one to ensure optimum performance. Caution: • Do not remove the light source lamp from inside of this equipment immediately after using the projector, you may get burned because of the high temperature of the light source lamp.
How to reset the operation time meter Plug in the power cord, switch on the projector and reset lamp time by pressing the , and POWER buttons simultaneously. Caution: • The light source lamp is fragile. Be careful not to cut yourself with the fragments. • The lamp life depends on the environment. For replacement lamps, please contact your dealer. The projector automatically shuts off when the lamp is used up in about 1,300 hours and not used until lamp replacement.
ENGLISH Maintenance Caution: Be sure to turn off the projector and unplug the power cord from the wall outlet before you perform any maintenance on the projector. Caution: Be sure to use the projector with an air-filter. If not, dust may get inside the projector, causing a fire or a breakdown. Cleaning the air-filter Cleaning the projector and the ventilation slots Clean the air-filter frequently.
Troubleshooting The following offers solutions to some of the common problems you may encounter. We suggest that you consult this chart before contacting your dealer. CAUSE The power is off. • The air intake vents, exhaust vents or air filter is clogged with dust or some object. Power indicator does not light up. • Power cord is unplugged from the outlet. • Power cord is disconnected from the projector. • The main switch is turned off. • The lamp lid is open. Power indicator blinks red.
Indicators The projector has three indicators each of which shows the working condition of the projector. ENGLISH The following offers solutions to possible problems. If a problem persists, turn the projector off and consult your dealer. LAMP TEMP RGB INDICATOR TEMP INDICATOR VIDEO SHOWS blinking red CONDITION • Unusual temperature The power is turned off and the POWER indicator lights up red. • The ventilation slots or air filter is clogged with dust or debris.
Type LCD projector Model LVP-X200A Rated power supply AC100 ~ 240V, 50 / 60Hz Rated input 5.0A LCD panels 1.3-inch LCD panel: 3 pieces (for R, G, B) ENGLISH Specifications Pixels 1,024 × 768 = 786,432 pixels Total 2,359,296 pixels Active pixel rate: 99.99 % or more (each panel) Projection lens F 2.3~2.
