Quick Start Manual

ManualsBrandsEpson ManualsPrintersEpson Epson Stylus Pro 4000 Professional Edition

Load Roll Paper

1 Slide the black paper stop off the end of

the spindle.

2 If the paper has a 2-inch core, remove the adapters

by pressing the four tabs.

Note: Make sure your hands are clean, and avoid touching the printable surface of the paper.

Try to handle paper by the edges. Make sure you don’t rub or scratch the coating or dent the

edges of the paper.

3 Position the roll so the paper unwinds as shown,

then slide it onto the spindle.

4 Slide the black paper stop back onto the spindle.

Insert it firmly into the end of the roll.

5 Open the roll paper cover.

6 Place the paper and spindle in the printer as

shown, with the gray end on the right.

7 Make sure the printer is powered on and

ready. Press the Paper Source button until

the or roll paper icon appears.

8 Release the paper lever.

9 Hold both sides of the paper and feed it into the slot until the paper

is aligned with the OTHER mark and the vertical line on the paper tray

cover. Then move the paper lever to the secured position.

10 Raise the roll paper support on top of the

paper tray. Then close the roll paper cover.

EPSON Stylus

Pro 4000

Unpack

1 Make sure you have all the parts shown below for your EPSON Stylus Pro 4000:

Warning: The printer weighs about 85 pounds, and should be lifted by two people.

2 Remove all the packing materials and

tape. Save the box and packaging in case

you need to ship the printer.

3 Loosen the two screws and remove the

carriage retainer bracket.

4 Unlock the print head carriage by

pulling the green tab to the left. Do

not remove the tab.

Note: To lock the print head carriage

for transportation, push the green tab to

the right.

Set Up and Plug In

1 Connect the power cord to the AC

inlet on the back of the printer.

2 Plug the other end of the power

cord into a properly grounded

electrical outlet.

3 Attach the exhaust port cover by sliding it

along the slots on the back of the printer.

4 Insert the paper tray into the slots at

the front of the printer.

Paper tray

Printer

Ink cartridges

Power cord

Roll paper spindle

Spindle adapters

(attached to spindle)

Start Here

Power button

AC inlet

Paper

Source

button

Roll paper cover

Exhaust port cover

vertical line

OTHER mark

CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 1

Summary of content (6 pages)

PAGE 1
CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 1 EPSON Stylus Pro 4000 ® Start Here Load Roll Paper Unpack 1 1 Slide the black paper stop off the end of the spindle. 2 If the paper has a 2-inch core, remove the adapters by pressing the four tabs. Make sure you have all the parts shown below for your EPSON Stylus Pro 4000: Note: Make sure your hands are clean, and avoid touching the printable surface of the paper. Try to handle paper by the edges.
PAGE 2
CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 1 EPSON Stylus Pro 4000 ® Start Here Unpack 1 Install Ink Load Roll Paper Use the ink cartridges that came with your printer for initial ink charging. During the initial installation process, it is normal for up to one-third of the ink in each cartridge to be used. 1 Slide the black paper stop off the end of the spindle. 1 2 If the paper has a 2-inch core, remove the adapters by pressing the four tabs. Press the Power button to turn on the printer.
PAGE 3
Load Roll Paper 1 Slide the black paper stop off the end of the spindle. 2 If the paper has a 2-inch core, remove the adapters by pressing the four tabs. Note: Make sure your hands are clean, and avoid touching the printable surface of the paper. Try to handle paper by the edges. Make sure you don’t rub or scratch the coating or dent the edges of the paper. 3 Position the roll so the paper unwinds as shown, then slide it onto the spindle. 4 Slide the black paper stop back onto the spindle.
PAGE 4
CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 2 Load Cut Sheet Paper When you are ready to print on cut sheet paper, make sure you release the paper lever and wind up the roll paper. Then return the paper lever to the secured position and close the roll paper cover. Note: Some papers cannot be used with the paper tray. You need to load them through the front or top manual feed slots. See the Printer Guide for details. 1 Make sure the printer is on and ready to print.
PAGE 5
CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 2 Connect to Your System You can use either of the following connections. Make sure your system has the appropriate port, and you have a standard, shielded cable 10 feet long or less: USB cable IEEE FireWire® cable If you have the optional EpsonNet Ethernet card, you can connect the printer directly to your network. You’ll need a standard RJ-45 network cable. 1 Make sure that both the printer and the computer are off.
PAGE 6
CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 2 10 Pull down the menu and select the connection you are using—either EPSON USB, EPSON FireWire, or EPSON TCP/IP. The Stylus Pro 4000 appears on the Printer List screen. 11 Click Stylus Pro 4000, then open the Page Setup pull-down menu. 12 Select All, then click Add. Windows 1 Make sure your printer is turned off. 2 Turn on your computer. 3 Insert the printer software CD-ROM in your computer. The installer starts automatically.