Specifications

routing wires. Personal injury and/or damage to the equipment could result from dropping or
mishandling it.
• Make sure the screen is completely closed before placing it on or lifting it off the wall or ceiling mount.
• Do not route the included power cables through the wall or ceiling. ey are not rated for this purpose.
Deliberate mis-installation could result in fire or other safety hazards. Either route the power cables
through the included wire management tracks, or plug them directly into nearby outlets.
• Some of the components included with this system may be packaged in plastic bags. Keep plastic bags
away from small children to avoid any risk of suffocation.
• is product should be operated only from the type of power source indicated on the marking label.
• If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of
the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode. See the drawing below
An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact
with them might be fatal.
• Do not place the components of this system near sources of heat or in direct sunlight.
• Make sure nothing blocks the ventilation openings on any of the components. Allow for sufficient heat
dispersion when components are installed on a rack. Do not block or cover the heatsink on the back of
the subwoofer.
• Where the mains plug is used as the disconnect device, the disconnect device shall remain readily operable.
• When unplugging the power cord of any system component, handle it carefully. Hold the plug when
unplugging the cord.
• is product should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of power supplied in your home, consult your product dealer or local
power company.
• Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk
of fire or electric shock.
• Keep the system components free from moisture, water, and dust.
• Do not let insecticides, benzene, or thinner come in contact with any components of the system.
• Never push objects of any kind through openings in the system components as they may touch dangerous
voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind
on the product.
• Except as specifically explained in these instructions, do not attempt to service this product yourself. Refer
all servicing to qualified service personnel.
• Never disassemble or modify the product in any way. Dangerous electrical voltages inside the components
can severely injure you.
• When replacement parts are required, be sure the service technician has used replacement parts specified by
the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, or other hazards.
• When closing the screen, be careful not to pinch your fingers where the screen closes against the case.
• Do not touch the white part of the screen with your hands. Oil from your skin could damage it.
• Never look into the projector lens when the lamp is turned on. e bright light can damage your eyes.
Never let children look into the lens when it is on.
• Don’t use the projector outside of the required temperature range of 41 to 95 °F (5 to 35 °C). Doing so
may cause an unstable display and could lead to projector damage.
• e lamp(s) in this product contain mercury. Please consult your state and local regulations regarding
disposal or recycling. Do not put in the trash.
• Allow the projector lamp to cool for one hour before replacing it.
WARNING: Handling the cord on this product or cords associated with accessories sold with this product, will
expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive
harm. Wash hands after handling. (is notice is provided in accordance with Proposition 65 in Cal. Health &
Safety Code § 25249.5 and following.)
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS