PG-C30XE SERVICE MANUAL SERVICE-ANLEITUNG S80H3PG-C30XE LCD PROJECTOR LCD PROJEKTOR MODEL MODELL PG-C30XE In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen Originalzustand gebracht werden.
PG-C30XE NOTE TO SERVICE PERSONNEL 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 Ë Lamp Replacement UV-RADIATION PRECAUTION 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 Note: Since the lamp reaches a very high temperature during units operation replacement of the lamp should be done at least one hour after the power has been turned off.
PG-C30XE Specifications Product type Model Video system Display method LCD panel Lens Projection lamp Contrast ratio Video input signal S-video input signal Horizontal resolution Audio output Computer RGB input signal Pixel clock Vertical frequency Horizontal frequency Computer control signal Speaker system Rated voltage Input current Rated frequency Power consumption Operating temperature Storage temperature Cabinet I/R carrier frequency Laser pointer of remote control Dimensions (approx.
PG-C30XE Location of Controls Projector LAMP REPLACEMENT indicator MUTE button TEMPERATURE WARNING indicator POWER indicator VOLUME buttons (+ / – ) POWER buttons (ON/OFF) KEYSTONE button MENU button AUTO SYNC button INPUT button FREEZE button RESIZE button ENLARGE button GAMMA button BLACK SCREEN button UNDO button ADJUSTMENT buttons ('/"/\/|) ENTER button Zoom knob Carrying handle Remote control sensor Kensington Security Standard connector Focus knob Foot release Front and Top View
PG-C30XE Operating the Wireless Mouse Remote Control Remote Control Front View Rear View MUTE button POWER buttons (ON/OFF) VOLUME buttons (+/–) KEYSTONE/BLACK SCREEN button LEFT-CLICK button LASER POINTER/ MENU button MOUSE/ ADJUSTMENT buttons ('/"/\/|) RIGHT-CLICK/ ENTER button UNDO button INPUT button AUTO SYNC button FREEZE button ENLARGE button RESIZE button TOOLS button GAMMA button MOUSE/ ADJUSTMENT switch BACKLIGHT button Top View Remote control signal transmitter Laser pointer wi
PG-C30XE Using the Remote Control as a Wireless Mouse The remote control has the following three functions: • Projector control • Wireless mouse • Laser pointer MOUSE/ADJUSTMENT switch (Remote control) MOUSE ADJ. MOUSE Wireless mouse Laser pointer ADJ. Projector control Remote Control/Mouse Receiver Positioning • The remote control can be used to control the projector within the ranges shown below.
PG-C30XE Use as a Wireless Mouse Effective buttons in MOUSE mode Be sure the supplied remote mouse receiver is connected to your computer. Remote control (Front view) (Slide the MOUSE/ADJUSTMENT switch on the remote control to the MOUSE position.) LASER POINTER MOUSE ADJ. BLACK SCREEN • The wireless mouse may not operate correctly if your computer serial port is not correctly set up. Refer to the computer’s operation manual for details of setting up/ installing the mouse driver.
PG-C30XE Connection Pin Assignments Analog Computer 1 and 2 Signal Input Ports: 15-pin mini D-sub female connector 1 6 11 5 10 15 Computer Input Analog 1. Video input (red) 2. Video input (green/sync on green) 3. Video input (blue) 4. Reserve input 1 5. Composite sync 6. Earth (red) 7. Earth (green/sync on green) 8. Earth (blue) 9. 10. 11. 12. 13. 14. 15. Component Input 1. PR (CR) 2. Y 3. PB 4. Not connected 5. Not connected 6. Earth (PR) 7. Earth (Y) 8. Earth (PB) 9. Not connected 10.
PG-C30XE Dimensions Rear View Top View 23 96.5 9 262 358.4 310 142 61 138.5 237.5 61 124.5 33.5 10 27.5 9 97.5 16 43 83 w 243.5 229 Front View 25 11 13 30 83 93 121 10.
PG-C30XE REMOVING OF MAJOR PARTS 1. Removing the Intake cover and lamp unit S H A R P 1-1. Detach the Intake cover. 1-2. Loosen the lamp cover screw and draw out the lamp cover in the direction of arrow (toward yourself). 1-3. Remove the two lamp unit lock screws. Detach the lamp unit. Lamp unit 1-3 1-3 1-2 Intake cover 1-1 Lamp cover Note: When replacing the lamp, make sure that there is a clearance of over 8mm between the terminal and the lamp snap-on spring (and other metallic parts).
PG-C30XE 2. Removing the top and rear cabinets 2-1. Remove the four rear cabinet lock screws. 2-2. Remove the four terminal board lock screws off the rear cabinet. Unhook and detach the rear cabinet from below. 2-3. Remove the four top cabinet lock screws from below. H S R A P Press both sides of the bottom cabinet in the directions of arrow to undo the hooks. Lift and detach the top cabinet. 2-1 2-3 Hook 2-2 2-4. Slowly lift the top cabinet and disconnect the operation key unit connector (KY).
PG-C30XE 3. Removing the PWB units 3-1. Disconnect the connectors from the output unit. 3-2. Remove the four PC I/F unit lock screws, and take out the PC I/F unit. 3-3. Remove the spacer (stud bolt) and the three screws off the output unit. Lift the output unit, together with the signal unit, off the position. 3-4. Remove the S-out/REG unit angle lock screw and take out the S-out/REG unit.
PG-C30XE 4. Removing the optical mechanism unit 4-1. Remove the six optical mechanism unit lock screws. Lift the unit off the position. 4-2. Remove the two lamp socket holder lock screws and take out the holder.
PG-C30XE 5. Removing the Power/Ballast unit assembly 5-1. Remove the Power/Ballast unit assembly lock screw. 5-2. Remove the (FG) lead lock screw. 5-3. Lift the Power/Ballast unit assembly off the position. 6. Removing the ballast unit and inlet unit 6-1. Disconnect the connector (PA) from the inlet unit. Take out the AC power switch. 6-2. Remove the Inlet unit lock screw. 6-3. Pull the inlet unit toward yourself off the position.
PG-C30XE RESETTING THE TOTAL LAMP TIMER When the lamp has been replaced, reset the total lamp timer in the following steps. Resetting procedure 1. While holding down the “ENTER”, “ADJ."” and “ADJ.|” keys on the set at the same time, turn on the main power switch (located side the AC inlet). 2. Now the total lamp timer is reset to zero. “000H” appears on the screen. LAMP POWER ON I TEMP.
PG-C30XE THE OPTICAL UNIT OUTLINE Layout of the optical system Note: Layout for positioning the optical system.
PG-C30XE CONVERGENCE AND FOCUS ADJUSTMENT » Start the convergence and focus adjustments with the top panel removed but the power on. Use the remote control to adjust the image. Take the following procedures. 1. Focusing the projection lens (A) Replacing all the 3 LCD panels 1. Before replacing all the 3 LCD panels, project an image on the screen and bring it into focus. 2. Replace the LCD panels with new ones.
PG-C30XE 4. With the G-LCD panel's screen center as refernce, adjust the R-LCD and B-LCD panels. 5. Finally tighten up the convergence lock screw "d". Notes : 1 The eccentric cam is used for convergence adjustment. This means that the cam's turning and the linear movement are not always uniform. 2 This model is not equipped with the LCD image adjustment mechanism. This is because the cross-dichroic prism is used for image formation.
PG-C30XE Convergence and Focus Adjustments at a Glance Adjustment directions Adjustment Direction X direction Convergence Y direction θZ direction Z direction Focus θX direction θY direction Definition Direction of LCD panel LCD right and left LCD top and bottom LCD turning axis LCD optical axis LCD top-to-bottom flapping LCD right-to-left flapping Rotation around Z axis Rotation around X axis Rotation around Y axis Convergence and Focus Adjustment for the Optical Mechanism Colour Adjustment Converg
PG-C30XE Replacing the LCD panels Detach the top panel and the optical mechanism unit in advance. (1) Remove the four prism holder lock screws. Detach the prism holder from the optical mechanism unit. (2) Remove the LCD panel lock screws (four each for the R-, G- and B-LCD panels). Detach the LCD panels from the prism holder. (3) Mount a new LCD panel in the reverse order of the above steps (1) and (2). ~ Readjust the convergence and focus.
PG-C30XE Adjusting the optical axis of the mirrors (M1, M5 and M4/M6) The optical axis must be readjusted if an eclipse happens with the R. G or B mirrors. Generally speaking, this adjustment is needed when any of the internal optical components has been replaced. Adjustment procedure required when any of the panels has been replaced or the convergence has been adjusted (1) Disconnect the flat cables of all the LCD panels. (2) Let the lamp light up.
PG-C30XE ELECTRICAL ADJUSTMENT Hook up a signal generator, or a DOSV or Mac personal computer to the projector in order to feed the signals specified in the Adjusting conditions. No. Adjusting point Adjusting conditions Adjusting procedure 1 EEPROM initialization 1. Turn on the power (make » Make the following settings: sure the lamp lights up) and Press SW5101 to call up the process mode and warm up the unit for 15 minexecute S2 in the SSS menu. Now the system, utes.
PG-C30XE No. 8 Adjusting point P SIGNAL Adjusting conditions Adjusting procedure 1. Connect the oscilloscope to » Adjust the PSIG waveform to the one shown below. TP1701 for red. (Adjust with PSIG-H.) TP1702 for green TP1703 for blue. PSIG 7.3±0.2V DC 2. Make the following choice: Group : OUTPUT 2 Subject : PSIG-H : PSIG-L 2.0V DC GND (Adjust with PSIG-L.) » For the green and blue colours, make sure their waveforms are similar to that of the red colour.
PG-C30XE No. Adjusting point Adjusting conditions Adjusting procedure 11 RGB countervoltage adjustment 1. Feed the black-and-red » Using the control switches or the remote controller (25%) stripe signal (XGA). buttons, adjust the data in order to minimize the 2. Make the following choice: flicker. Group : OUTPUT 3 Subject : RC (R) » Make the same adjustment for BC (B), GC (G), and RC-INV (B) and RC-INV (G).
PG-C30XE No. Adjusting point Adjusting conditions Adjusting procedure 16 Video brightness adjustment 1. Feed the baseband (split » Using the control switches or the remote controller colour bar) signal. (The ONbuttons, adjust the setting until the black signal AIR signal is not accepted becomes bit-less. because of its too much noise.) Group : VIDEO 2 Subject : VROS/VGOS/VBOS 2. Press the control switch or the remote control’s mute button (to set the gamma correction to the process setting).
PG-C30XE No. Adjusting point Adjusting conditions Adjusting procedure 22 Video input panel signal amplitude adjustment 1. Feed the NTSC 10-step sig- » Select R1-GAIN and adjust the setting so that the nal. R and G signals have the same amplitude. 2. Select the following group » For the blue colour, adjust the setting the same and subject. way. Group: VIDEO2 Subject: R1-GAIN B1-GAIN 3. Connect the oscilloscope to TP1101 (R) and TP1201 (G). 4.
PG-C30XE No. Adjusting point Adjusting conditions 1. Receive the RGB signal. Adjusting procedure » In the process mode and select L4. Check the picture, brightness, red, blue, clock, phase, horizontal position, and vertical position. 30 RGB performance check 31 Off-timer performance check 32 Thermistor performance check 1. Heat the thermistor using a » Make sure the “TEMP” is displayed. dryer. 33 Automatic synchronization 1.
PG-C30XE ADJUSTING THE PC BOARD (CPCi-0047CE02. PC I/F Unit) 1. Setting the oscilloscope Set the range to DC 1 V/div and 5µs/div. 2. Connecting the PC interface 1) Connect the PC interface to the projector. Make surethe CON2 (P8404), CON3 (P8502) and CON4 (P8405)connectors are all tight in position. 2) Connect the cable between the computer’s ANALOG OUTPUTterminal and the DSUB (INPUT1 on the projector)connector. 3) Set the projector’s input selector to the RGB1position.
PG-C30XE TROUBLE SHOOTING TABLE Checking the PWB performance Video input in trouble RGB input in trouble Through-output in trouble Remote control in trouble Go to "Checking the video unit Feed test pattern signal from Through-output circuit in Go to "Checking the remote circuit". PC. trouble. control". Is specified cable connected No between PC and projector? Yes Use specified cable. Is supply voltage as specified? No Yes Power circuit in trouble.
PG-C30XE TROUBLE SHOOTING TABLE (Continued) Checking the video system No Is the lamp on? Yes Go to "Lamp fails to light-up". No Is specified voltage fed to EA connectors? Yes Check the power circuit and its parts. Are there signal inputs at pins (3) and (29) of P402? No Yes Are there signals at pin (4) of IC401 and pin (4) of IC402? Are there signal outputs at pins (3) and (6) of IC816? Yes Yes No Go to "Checking IC801 (RGB signal output circuit)".
PG-C30XE TROUBLE SHOOTING TABLE (Continued) Checking IC801 (RGB signal output circuit) No Are there RGB output waveforms at No pins (31), (32) and (33) of IC801? Yes Go to "No colour or unusual tone", Check the data transfer and other "No Y signal" or "Out of sync". performance at pins (17) and (18) of Are there output waveforms at the emitters of Q1501, Q1502 and video IC801. No Q1503? Yes Check Q1501 thru Q1503, SC1501 and their peripheral circuits.
PG-C30XE TROUBLE SHOOTING TABLE (Continued) Checking IC806 (3-D noise reduction circuit) and its peripheral circuits Are there signal inputs at pins (40) (Y signal) and (45)(chroma signal) of No IC806? Yes Check the buffer circuit of Q814 thru Q816 as well as Q903 thru Q906. Are there signal outputs at pins (55) No (Y signal) and (51)(chroma signal) of IC806? Yes Check IC806, IC807 (memory) and their peripheral circuits.
PG-C30XE TROUBLE SHOOTING TABLE (Continued) No or unusual Y signal Is there Y signal input at pin (21) of No IC801? Yes Go back to the signal processing block. Is there Y signal output at pin (40) of No IC801? Yes Check IC801 and its peripheral circuits. Is there Y signal output at pin (17) of No IC803? Yes Check IC803 and its peripheral circuits as well as IC805 (AGC). Check IC803 and its peripheral circuits.
PG-C30XE TROUBLE SHOOTING TABLE (Continued) Checking the output PWB unit No Are there signal inputs at SC1404, SC1405, SC1501 and No SC1502? Are voltages applied to EA If there is no signal at SC1501 If there is no signal at SC1404 and SC1502, go to the video and SC1405, go to "Trouble system block. shooting table for PC I/F unit".
PG-C30XE TROUBLE SHOOTING TABLE (Continued) No audio output Are there audio signal inputs at pin No (2) of IC1411? Yes Check the input, the switching circuit of IC3303 and IC3304, and their peripheral circuit,SC3001,SC1502,etc. Are there audio signal outputs at pin No (2) of P5508? Yes Check the IC1411 control voltage,and its peripheral circuits. Are there audio signal outputs at pin No (6) of IC7301? Yes Check IC7301 and its peripheral circuits.
PG-C30XE TROUBLE SHOOTING TABLE (Continued) Power on Is the right input selected? No Yes Select the right input with remote control. Are the PC, video and LCP cables as No specified and properly connected? Yes Use the right cables or reconnect the cables. With the contrast control at maximum, Yes does the image appear? No Readjust the video system. Is the voltage at CON3 (P8502) No connector as specified? Yes Power circuit faulty. Hook up a personal computer.
PG-C30XE TROUBLE SHOOTING TABLE (Continued) Lamp fails to light-up Yes Turn on the power switch. Is discharging sound heard from the lamp? No Is the lamp out of socket? Yes No Is the ballast cooling fan No running? Reconnect the Replace the lamp into socket. lamp. Yes Check the power circuit. Is DC 360V voltage applied No between PL connector pins? Yes Yes Is 2V or higher voltage applied between pins (1) and (2) of ballast's D connector? No Replace the ballast.
PG-C30XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-1 Checking the clock circuit and its peripheral circuits Is X8001 (6MHz) oscillating? No X8001 or its peripheral part faulty. Yes Is X8003 (1.84MHz) oscillating? No X8003 or its peripheral part faulty. Yes Is X8004 (22.165MHz) oscillating? No X8004 or its peripheral part faulty. Yes Is X8005 (16.25MHz) oscillating? No X8005 or its peripheral part faulty. Yes Does pin (162) of IC8001 function? No IC8001 or its peripheral circuit faulty.
PG-C30XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-2 Checking the PLL circuit and its peripheral circuits Are there signals at pin(111) of IC8606 and TL8606? No Yes IC8025 or its peripheral circuit faulty. Are there signals at pins (100) and (101) of IC8606? No Yes IC8606 or its peripheral circuit faulty. Check the video circuit and its peripheral circuits.
PG-C30XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-3 Checking the SXGA's red video circuit and its peripheral circuits Is there signal at pin (139) of IC8606? Checking the VGA's red video circuit and its peripheral circuits No No Is there signal at pin (139) of IC8606? Yes Yes output PWB faulty.
PG-C30XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-4 Checking the SXGA's green video circuit and its peripheral circuits Is there signal at pin (124) of IC8606? Checking the VGA's green video circuit and its peripheral circuits No No Is there signal at pin (124) of IC8606? Yes Yes output PWB faulty.
PG-C30XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-5 Checking the SXGA's blue video circuit and its peripheral circuits Is there signal at pin (133) of IC8606? Checking the VGA's blue video circuit and its peripheral circuits No No Is there signal at pin (133) of IC8606? Yes Yes outpur PWB faulty. Are there signals at pins (45) thru (49), (51), thru (53), (56) thru (58), (60) thru (64) of IC8606? No Yes Are there signals at TL8048 and TL8049? No Yes IC8606 or its peripheral circuit faulty.
PG-C30XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-6 Checking the OSD circuit and its peripheral circuits Display OSD on the screen. Are there signals at pins (56), (58), (71) and (72) of IC8048? No Yes IC8029 or its peripheral circuit faulty. Are there signals at pins (12), (14) thru (17) and (20) of IC8048? No Yes IC8048 or its peripheral circuit faulty. Are there signals at pins (23) thru (42) of IC8048? No Yes IC8046, IC8047 or their peripheral circuit faulty.
PG-C30XE CHASSIS LAYOUT / CHASSIS-ANORDNUNG OUTPUT UNIT DUNTKA215DE02 H PC I/F UNIT CPCI-0047CE02 INLET UNIT RUNTK0677CEZZ G F SIGNAL UNIT DUNTKA211DE02 E S-OUT/REG UNIT DUNTKA214DE02 VIDEO UNIT DUNTK9769DE21 D C POWER UNIT RDENC0311CEZZ BALLAST UNIT RDENC0313CEZZ B PC TERMINAL UNIT DUNTKA212DE02 A 1 2 3 86 4 5 6 7 8 9 10 11 87 12
PG-C30XE BLOCK DIAGRAM / BLOCKSCHALTBILD H G F E D C B A 1 2 3 88 4 5 6 7 8 9 10 11 89 12
PG-C30XE OVERALL WIRING DIAGRAM / GESAMTSCHALTPLAN H G F E D C B A 1 2 3 90 4 5 6 7 8 9 10 11 91 12
PG-C30XE DESCRIPTION OF SCHEMATIC DIAGRAM BESCHREIBUNG DES SCHEMATISCHEN SCHALTPLANS H VOLTAGE MEASUREMENT CONDITION: SPANNUNGSMESSUNGEN: 1. Voltages at test points are measured at the supply voltage of AC 230V. Signals are fed by a colour bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester. 1.
PG-C30XE WAVEFORMS / WELLENFORMEN 1 SC1101 18-pin 2 SC1101 19-pin (RP SIG5) H : 10µsec/div V : 2V/div (RP SIG6) H : 10µsec/div V : 2V/div 5 SC1301 18-pin 7 P801 1-pin (BP SIG6) H : 10µsec/div V : 2V/div 9 P801 4-pin 8 P801 2-pin (R) H : 10µsec/div V : 0.5V/div 0 IC604 6-pin (B-Y) H : 20µsec/div V : 1V/div (GP SIG6) H : 10µsec/div V : 2V/div (GP SIG5) H : 10µsec/div V : 2V/div 6 SC1301 19-pin (BP SIG5) H : 10µsec/div V : 2V/div 4 SC1201 19-pin 3 SC1201 18-pin (G) H : 20µsec/div V : 0.
PG-C30XE Ë SIGNAL UNIT-1/2 / SIGNALEINHEIT-1/2 H G F E D C B A 1 2 3 94 4 5 6 7 8 9 10 11 95 12
PG-C30XE Ë SIGNAL UNIT-2/2 / SIGNALEINHEIT-2/2 H G F E D C B A 1 2 3 96 4 5 6 7 8 9 10 11 97 12
PG-C30XE Ë PC TERMINAL UNIT / PC-ANSCHLUßEINHEIT H G F E D C B A 1 2 3 98 4 5 6 7 8 9 10 11 99 12
PG-C30XE Ë SOUND OUT and REGULATOR UNIT / TONAUSGABE-und REGLEREINHEIT H G F E D C B A 1 2 3 100 4 5 6 7 8 9 10 11 101 12
PG-C30XE Ë OUTPUT UNIT-1/6 / AUSGABEEINHEIT-1/6 H G F E D C B A 1 2 3 102 4 5 6 7 8 9 10 11 103 12
PG-C30XE Ë OUTPUT UNIT-2/6 / AUSGABEEINHEIT-2/6 H G F E D C B A 1 2 3 104 4 5 6 7 8 9 10 11 105 12
PG-C30XE Ë OUTPUT UNIT-3/6 / AUSGABEEINHEIT-3/6 H G F E D C B A 1 2 3 106 4 5 6 7 8 9 10 11 107 12
PG-C30XE Ë OUTPUT UNIT-4/6 / AUSGABEEINHEIT-4/6 H G F E D C B A 1 2 3 108 4 5 6 7 8 9 10 11 109 12
PG-C30XE Ë OUTPUT UNIT-5/6 / AUSGABEEINHEIT-5/6 H G F E D C B A 1 2 3 110 4 5 6 7 8 9 10 11 111 12
PG-C30XE Ë OUTPUT UNIT-6/6 / AUSGABEEINHEIT-6/6 H G F E D C B A 1 2 3 112 4 5 6 7 8 9 10 11 113 12
PG-C30XE Ë VIDEO UNIT / VIDEOEINHEIT H G F E D C B A 1 2 3 114 4 5 6 7 8 9 10 11 115 12
PG-C30XE Ë POWER and INLET UNIT / NETZ-und EINGANGSEINHEIT (POWER) H G F E D C (INLET) B A 1 2 3 116 4 5 6 7 8 9 10 11 117 12
PG-C30XE Ë PC I/F UNIT-1/9 / PC-I/F EINHEIT-1/9 H G F E D C B A 1 2 3 118 4 5 6 7 8 9 10 11 119 12
PG-C30XE Ë PC I/F UNIT-2/9 / PC-I/F EINHEIT-2/9 H G F E D C B A 1 2 3 120 4 5 6 7 8 9 10 11 121 12
PG-C30XE Ë PC I/F UNIT-3/9 / PC-I/F EINHEIT-3/9 H G F E D C B A 1 2 3 122 4 5 6 7 8 9 10 11 123 12
PG-C30XE Ë PC I/F UNIT-4/9 / PC-I/F EINHEIT-4/9 H G F E D C B A 1 2 3 124 4 5 6 7 8 9 10 11 125 12
PG-C30XE Ë PC I/F UNIT-5/9 / PC-I/F EINHEIT-5/9 H G F E D C B A 1 2 3 126 4 5 6 7 8 9 10 11 127 12
PG-C30XE Ë PC I/F UNIT-6/9 / PC-I/F EINHEIT-6/9 H G F E D C B A 1 2 3 128 4 5 6 7 8 9 10 11 129 12
PG-C30XE Ë PC I/F UNIT-7/9 / PC-I/F EINHEIT-7/9 H G F E D C B A 1 2 3 130 4 5 6 7 8 9 10 11 131 12
PG-C30XE Ë PC I/F UNIT-8/9 / PC-I/F EINHEIT-8/9 H G F E D C B A 1 2 3 132 4 5 6 7 8 9 10 11 133 12
PG-C30XE Ë PC I/F UNIT-9/9 / PC-I/F EINHEIT-9/9 H G F E D C B A 1 2 3 134 4 5 6 7 8 9 10 11 135 12
PG-C30XE PRINTED WIRING BOARD ASSEMBLIES/ LEITERPLATTENEINHEITEN H G F E Signal Unit (Wiring Side)/ Signaleinheit (Leiterbahnseite) D C PC Terminal Unit (Wiring Side)/ PC-Anschlußeinheit (Leiterbahnseite) B A Video Unit (Wiring Side)/ Videoeinheit (Leiterbahnseite) 1 2 3 4 136 5 6
PG-C30XE H G F E Signal Unit (Component Side)/ Signaleinheit (Bestückungsseite) D C PC Terminal Unit (Component Side)/ PC-Anschlußeinheit (Bestückungsseite) B A Video Unit (Component Side)/ Videoeinheit (Bestückungsseite) 1 2 3 4 137 5 6
PG-C30XE H G F E D C B A Output Unit (Wiring Side)/ Ausgabeeinheit (Leiterbahnseite) 1 2 3 4 138 5 6
PG-C30XE H G F E D C B A Output Unit (Component Side)/ Ausgabeeinheit (Bestückungsseite) 1 2 3 4 139 5 6
PG-C30XE H G F E PC I/F Unit (Wiring Side)/ PC-I/F-Einheit (Leiterbahnseite) D C B A PC I/F Unit (Component Side)/ PC-I/F-Einheit (Bestückungsseite) 1 2 3 4 140 5 6
PG-C30XE H G F E Sound Out/Regulator Unit (Wiring Side)/ Tonausgabe/Reglereinheit (Leiterbahnseite) D C B A Sound Out/Regulator Unit (Component Side)/ Tonausgabe/Reglereinheit (Bestückungsseite) 1 2 3 4 141 5 6
PG-C30XE H G F E Sound Out/Regulator Unit (Wiring Side)/ Tonausgabe/Reglereinheit (Leiterbahnseite) D C B A Sound Out/Regulator Unit (Component Side)/ Tonausgabe/Reglereinheit (Bestückungsseite) 1 2 3 4 141 5 6
PG-C30XE H G F Power Unit (Wiring Side)/ Netzeinheit (Leiterbahnseite) E D C B Power Unit (Component Side)/ Netzeinheit (Bestückungsseite) A 1 2 3 4 142 5 6
PG-C30XE H G F Inlet Unit (Wiring Side)/ Eingangseinheit (Leiterbahnseite) E D C B Inlet Unit (Component Side)/ Eingangseinheit (Bestückungsseite) A 1 2 3 4 143 5 6
PG-C30XE Ref. No. Part No. ★ Description PARTS LIST Code Ref. No. Part No. ★ Description Code ERSATZTEILLISTE PARTS REPLACEMENT AUSTAUSCH VON TEILEN Replacement parts which have these special safety characteristics identified in this manual: electrical components having such features are identified by "å" in the Replacement Parts Lists.
PG-C30XE Ref. No. ★ Part No.
PG-C30XE Ref. No. ★ Part No.
PG-C30XE Ref. No. Part No.
PG-C30XE Ref. No. ★ Part No.
PG-C30XE Ref. No. Part No.
PG-C30XE Ref. No. ★ Part No.
PG-C30XE Ref. No. Part No.
PG-C30XE Ref. No. ★ Part No.
PG-C30XE Ref. No. Part No.
PG-C30XE Ref. No. Part No. ★ Description Code Ref. No. Part No.
PG-C30XE Ref. No. Part No.
PG-C30XE Ref. No. Part No. ★ Description Code Ref. No. Part No.
PG-C30XE Ref. No. Part No.
PG-C30XE Ref. No. Part No. ★ Description Code Ref. No. ★ Part No.
PG-C30XE Ref. No. R6007 R6008 R6011 R6047 R6049 R6050 R6051 R6052 R6053 R6054 R6055 R6056 R6057 R6058 R6059 R6060 R6061 R6062 R6063 R6064 R6069 R6070 R6071 R6072 R6073 R6074 R6075 R6076 R6081 R6082 R6085 R6087 R6088 R6089 R6090 R6091 R6092 R6094 R6095 R6096 Part No. ★ Description Code Ref. No. ★ Part No.
PG-C30XE Ref. No. ★ Part No.
PG-C30XE Ref. No. ★ Part No.
PG-C30XE Ref. No. Part No.
PG-C30XE Ref. No. Part No. ★ Description Code Ref. No.
PG-C30XE Ref. No. Part No.
A 1 2 58 20 3 165 9 F SP 4 5 25 SO 33 48 45 C B 3-6 3-19 3-2-14 3-7 3-23 3-8 3-9 1-3 F 3-24 3-10 3-2-5 3-17 3-5 3-25 3-16 1-6 L 3-2-2 3-2-1 3-2-9 3-2-9 3-2-13 3-2-12 1-1-6 6 3-2 3-2-4 3-2-7 1-1 C 3-11-2 3-12 3-2-8 3-22 3-11 3-20 3-21 3-2-6 3-2-11 A 3-2-10 59 2-2 2-1 3-11-1 3-3 3-1 3-1-2 3-1-4 3-1-3 43 3 E 3-1-1 3-1-1-1 3-1-1-3 3-1-1-4 3-1-1-2 29 57 2-1-1 2-1-2 35 Part No. ★ Description Code Ref. No. Part No.
PG-C30XE Ref. No. ★ Part No.
1 2 A 6-86 6-11 B 3 167 4 6-57 6-12 6-53 6-75 6-89 6-68 6-90 6-45 6-83 6-79 6-79 6-91 6-47 6-78 6-85 6-39 6-54 6-19 6-18 6-17 6-26 6-1 6-24 6-29 6-30 6-2 6-14 6-16 6-14 6-49 6-32 6-31 6-23 6-27 6-54 6-25 6-54 6-92 6-35 6-20 6-22 6-25 6-32 6-51 6-66 6-51 6-14 6-51 6-21 6-73 6-80 6-10 5 6-8 6-81 6-15-2-1 6-15-4 6-15-5 6-15-7 6-15-2-3 6-15-2 6-77 6-52 6-15-9 6-15-12 6-15-2-2 6-15-10 6-72 6-15-3 6-15-6 6-15-8 6-88 6-79 6-79 6-87 6-1
PG-C30XE Ref. No. Part No.
PG-C30XE Part No. ★ Description Ref. No. Part No. POWER/BALLAST UNIT Code PARTS/ TEILE FÜR NETZ-/BALLASTEINHEIT ★ Ref. No.
PG-C30XE Ref. No. Part No. ★ Description Code å J Extra Air Filter AE J AC Cord (For Europe) AZ J AC Cord BA (For U.K.
PG-C30XE Part No. ★ Description Ref. No. Part No. ★ Description PACKING OF THE SETCode / VERPACKEN DES GERÄTS Ref. No.
PG-C30XE Ref. No. Part No. ★ Description Code Ref. No. ★ Part No. Description Code COPYRIGHT © 2000 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. D Japan P Japan TQ0974-S Sep.
