Data Sheet

ManualsBrandsEnda ManualsAutomationPID Universal controller Pt100, J, K, L, T, S, R SSR, 8 A relay (W x H) 48 mm x 48 mm

Table Of Contents

EN 60584

DIN 43710

EN 60584

EN 60751

°C

°F

-199.9...600.0

-30.0....600.0°C

-30.0...999.9°C

-30.0...400.0°C

-200...600

-30....600°C

-30...1300°C

-30....400°C

-40...1700°C

°C

-22.0....999.9 °F

-22.0....752.0 °F

-199.9...999.9

-22....2372 °F

-22......752

-40....3092

-328....1112

-22....1112 °F

°F

Order Code : EUP

1 - Size

4420.....48x48x87mm

7420.....72x72x97mm

8420.....48x96x87mm

9420.....96x96x50mm

2 -

230VAC...90 - 250V AC

SM..........10-30V DC /

8-24V AC

Supply Voltage

3 -

RS........ RS-485

Blank....

Modbus (Optional)

Modbus Available

(Optional / Specify at order).

N/A

2 3

DIN 43710

ENDA EUP SERIES PID UNIVERSAL CONTROLLER

Thank you for choosing ENDA EUP Series Universal Controller Devices.

ase

bef

s p

wil

ida

mag

by n

wing

str

tio

ailed

man

. T

sible

for a

r losses

use

ch m

ay b

xpe

of t

ins

ion

duc

Dual setpoint value can be selected.

PT100 ,J, K, L, T, S, R sensor (thermocouple) types can be selected.

0-20mA, 4-20mA, 0-10V, 2-10V, 0-25mV and 0-50mV input selections.

Auto calculation for PID parameters (SELF TUNE).

Three different feature can be assigned to digital input.

Three different feature can be assigned to F function key.

Soft-Start feature.

Analogue, SSR or Relay Output Control selection.

0-20mA and 4-20mA Analogue Output Control selection.

Up to 16 steps Profile Control.

A1 Relay output programmable as first Alarm or Cooling control output.

C/A2 Relay output can be used as second Alarm or Temperature Control output.

Heating/Cooling control selection.

Zero point input shift.

In case of sensor failure, periodically, auto-periodically running or relay state can be selected.

Rs485 Modbus RTU communication protocol feature (Specify at order).

Self tune for automatic PID calculation or

manually enter PID parameters if known.

Input Type

Scale Range

J (Fe-CuNi) Thermocouple

L (Fe-CuNi) Thermocouple

J (Fe-CuNi) Thermocouple

L (Fe-CuNi) Thermocouple

K (NiCr-Ni) Thermocouple

T (Cu-CuNi) Thermocouple

S (Pt10Rh-Pt) Thermocouple

R (Pt13Rh-Pt) Thermocouple

PT100 Resistance Thermometer

0-20mA input

0-10V input

2-10V input

0-25mV input

0-50mV input

4-20mA input

-1999...+9999 (max. scale range 10000)

0,5% (for full scale)

1 digit

0,5% (for full scale)

1 digit

0,5% (for full scale) 1 digit

0,2% ( )for full scale

1 digit

0,2% ( )for full scale 1 digit

0,2% ( )for full scale

1 digit

Accuracy

ENVIRONMENTAL CONDITIONS

Height

Ambient/storage temperature

Max. Relative humidity

Rated pollution degree

ELECTRICAL CHARACTERISTICS

Supply

Power consumption

Wiring

Line resistance

Data retention

EMC

Safety requirements

OUTPUTS

A1 Output

Life expectancy for relay

C/A2 Output

ANL/SSR Output

CONTROL

Control type

Control algorithm

A/D converter

Sampling time

Proportional band

Control period

Hysteresis

Output power

HOUSING

Housing type

Dimensions

Weight

Enclosure material

90-250V AC, 50/60Hz or 10-30VDC / 8-24VAC ±%10 SMPS

Max. 5VA

Power screw-terminal connections: 2.5mm², Signal screw-terminal connections: 1,5mm².

EN 61326-1: 2013 (Performance criterion B satisfied for EN 61000-4-3 standard).

EEPROM (minimum 10 years)

Max. 100 Ohm

EN 61010-1: 2010 (Pollution degree 2, overvoltage category II)

Suitable for flush-panel mounting according to DIN 43 700.

EUP4420 : W48xH48xD87mm, EUP7420 : W72xH72xD97mm,

EUP8420 : W48xH96xD87mm, EUP9420 : W96xH96xD50mm.

Approx. 400g (250g for EUP4400) After packing.

Self extinguishing plastics

Single Setpoint and Alarm Control.

On-Off / P, PI, PD, PID (selection).

14 bit.

Min. 100ms.

Can be adjusted between %0.0 and %100.0 . If Pb=%0.0 , ON-OFF control is selected.

Can be adjusted between 1 and 125secs.

Can be adjusted between 1 and 50°C/F.

Setpoint value ratio can be adjusted between %0 and %100 .

Relay : 250V AC, 8A (for resistive load), NO+NC (Control or Alarm2 Output selection).

Relay : 250V AC, 8A (for resistive load), NO (Alarm1 and Cooling Control Output selection).

Max. 2000m

0 ... +50°C/-25 ... +70°C

According to EN 60529; Front panel : IP65, Rear panel : IP20

Max. SSR Output ; 0-20mA, 4-20mA, 24V 20mA. Max. load resistance ; 600 Ohm (12 bit 0.2% accuracy).

Relative humidity 80% for temperatures up to 31°C decreasing linearly to 50% relative humidity at 40°C.

Without load 30.000.000 switching; 250V AC, 8A (resistive load) 300.000 switching.

KEEP AWAY device from exposed to corrosive, volatile and flammable gases or liquids and DO NOT USE the device in similar hazardous locations.

DO NOT clean the device with solvent (thinner, gasoline, acid etc.) and / or abrasive cleaning agents.

Please see EUPx420

Series Modbus Address

Map and Connection

Diagram Guide for

Modbus feature.

UNIVERSAL CONTROLLER

ENDA

EUP7420

C/A2

SSR

C/A SET

SET

A1 DEL.

A2 INS.

START

STOP

UNIVERSAL CONTROLLER

ENDA

C/A SET

SET

EUP4420

C/A2

SSR

1200

START

STOP

A1 DEL.

A2 INS.

C/A2

SSR

UNIVERSAL CONTROLLER

EUP9420

ENDA

SET

C/A SET

START

STOP

A1 DEL.

A2 INS.

EUP8420

ENDA

UNIVERSAL CONTROLLER

SET

C/A SET

C/A2

SSR

START

STOP

A1 DEL.

A2 INS.

english

1. / 7

E-mail : info@suran-elektronik.de

Internet : www.suran-elektronik.de

Tel.: +49 (0)7451 / 625 617

Fax: +49 (0)7451 / 625 0650

SURAN Industrieelektronik

Dettinger Str. 9 / D-72160 Horb a.N

EUPx420-E-08092021

up to date: 08.09.2021, modification reserved and can be change any time previous notice !

Summary of content (12 pages)

PAGE 1
english Please read this document carefully before using this product. The guarantee will be invalidated if the device is damaged by not following instructions detailed in the manual. The company shall not be responsible for any damage or losses however caused, which may be experienced as a result of the installation or use of this product. ENDA EUP SERIES PID UNIVERSAL CONTROLLER Thank you for choosing ENDA EUP Series Universal Controller Devices. Dual setpoint value can be selected.
PAGE 2
ENTERING TO PROGRAMMING MODE SET If SET key is pressed while holding C/A SET key, the "Programming Mode" is entered. F C/A SET F Page 3 Con.o. A2 INS. STOP Al1.o. A F A2 s.lo. = Lower limit for C/A2 C.s.Lo. C. Output control, setpoint value. -30 Can be adjusted between 0 and C.s.Hi. Upper scale value. A2 if the C.O.SE. parameter set to A.Con. , this menu can not be displayed (disabled). A1.S.L limit. -30 Can be adjusted between 0 and A1.S.H parameter value.
PAGE 3
RUNNING MODE During in "Programming Mode", if no key is pressed for 20 sec, settings automatically saved and device returns to the "Running Mode" (to the SET home screen). Alternatively, by pressing key "Running Mode" is entered and by pressing both keys at once, settings automatically F F C/A SET saved and device returns to the "Running Mode" (to the home screen). SET F C/A SET P. 2 s.tun. A2 P.CnF.. E INS. F A2 STOP s.t.us. F A2 s.t.us. = Self tune Control Parameter. if the P.Con.
PAGE 4
TERMS AND DISPLAY ( 1 ) Indicates measured value and set values in “Running Mode”. Indicates the parameters and names in “Programming Mode”. EUP4420 C/A2 1200 1200 AN/SSR (7) A1 ( 2 ) Lights up, if timer is displayed and flashes while timer is running. PV ( 3 ) Increment key in “Running and Programming Mode”. Parameter selection key in “Programming Mode”. ( 4 ) Decrement key. By pressing this key in “Running Mode”, software version can be displayed. Parameter selection key in “Programming Mode”.
PAGE 5
MOTORIZED VALVE CONNECTION AND SETTINGS N OPEN L 13 AC 250V 8A RESISTIVE LOAD C/A2 (VALVE OPEN) 14 15 16 CLOSE A1 AC 250V 8A RESISTIVE LOAD (VALVE CLOSE) 17 Motorized valve connection must be applied as shown figure above (if the motorized valve electrical values are incompatible with EUPx420 contact output values, an additional contactor must be connected). And C.o.SE. parameter in the EUPx420 must be selected as A.con..
PAGE 6
MULTI-STEP PROFILE CONTROL OUTPUT GRAPHICS Target Temperature Time A1 A2 Step1 Step2 Step3 tE.01 =100 ti.01 = 30 ON OFF tE..02 =100 ti.02 = 20 OFF ON Step4 tE..03 =300 ti.03 = 60 OFF OFF Diagram-5 Step5 tE..04 =300 ti.04 = 40 ON ON tE..05 =100 ti.05 = 60 OFF OFF S.num parameter should be set to 5 for five step program. If A1.P.c parameter is set as on , A1 runs according to profile program value. If A1.P.c parameter set asindE , A1 output will be activated according to A1.SE. value. A1 If C.
PAGE 7
DIMENSIONS Depth 1 2 EUP4420 C/A2 58mm 48mm SSR A1 To removing the device from the panel: - While pressing both side of the device in direction 1 , and push it in direction 2 . 1200 1200 Connection Cables PV Flush mounting clamp SV A1 SET C/A SET F ENDA DEL. A2 INS.
PAGE 8
ENDA EUPx420 SERIES PID TEMPERATURE CONTROLLER MODBUS PROTOCOL ADDRESS MAP 1.1 Memory Map for Holding Registers Parameter Holding Register Data Adress Type Number Data Content Configuration Parameters A2 Output Parameters A1 Output Parameters Control Output Parameters Decimal (Hex) Read / Write Parameter Default Value Name Permission 0000d (0000h) Word Control output, temperature setpoint value R/W C1.SE. 400 0001d (0001h) Word Control output, 2nd temperature setpoint value R/W C2.SE.
PAGE 9
ENDA EUPx420 SERIES PID TEMPERATURE CONTROLLER MODBUS PROTOCOL ADDRESS MAP 1.
PAGE 10
ENDA EUPx420 SERIES PID TEMPERATURE CONTROLLER MODBUS PROTOCOL ADDRESS MAP 2.1 Memory Map for Profile Control Holding Registers Step Control Parameters Holding Register Data Parameter Adress Number Decimal (Hex) Type Read / Write Parameter Default Value Permission Name Data Content PH0 PH1 0100d (0064h) Word Profile time base set value. (0 = 0000s,1 = 00m59s, 2 = 0000m, 3 = 99m59s) Maximum number of steps (can be adjusted between 0 and 16.
PAGE 11
ENDA EUPx420 SERIES PID TEMPERATURE CONTROLLER MODBUS PROTOCOL ADDRESS MAP 2.2 Memory Map for Step Control Bits Parameter Coil Address Data Type Number Read / Write Parameter Default Name Permission Value Data Content 0100d PC0-PC15 0115d (0064h) (0073h) Bit 0116d PC16-PC31 0131d (0074h) (0083h) Bit PC32 0132d (0084h) Bit PC33 0133d (0085h) Bit PC34 0134d (0086h) Bit A1 alarm output programming coils in profile steps ; If PC0=1, A1 output is ON at 1st step....
PAGE 12
ENDA EUPx420 SERIES PID TEMPERATURE CONTROLLER MODBUS PROTOCOL ADDRESS MAP 4. MODBUS ERROR MESSAGES Modbus protocol has two types error, communication error and operating error. Reason of the communication error is data corruption in transmission. Parity and CRC control should be done to prevent communication error. Receiver side checks parity and CRC of the data. If they are wrong, the message will be ignored.