Use and Care Manual

Single Color Selection Feature
Find your favorite color on the remote’s color pad and simply push that
button to set all of the lights the same color.
NOTE: Within this feature, you can also press the dimming button to adjust
from 10 dierent light levels. The dimming option is only available for
single- and dual-color selection.
Dual-Color Selection Feature
A - Press Color 1, then select a color from the color pad to set the color of every
other bulb starting with the first bulb.
B - Press Color 2, then select a color from the color pad to set the color of every
other bulb starting with the second bulb.
C - During the selection feature, press the dimming button to choose one of 10
dierent light levels.
Strobe Selection Feature
By pressing the Strobe button, the lights will strobe through all of the colors
in a random pattern.
Fade Selection Feature
By pressing the Fade button, the lights will fade in and out through all of the
colors in a random pattern.
Modes Selection Feature
Press the “modes” button repeatedly to cycle through the following preset modes:
•Twinkle •Multi Fade •Christmas •St. Patrick’s Day
•Red, white and blue •Fall •Spring •Multi
Timer Selection Feature
A - By pressing the 2 Hour Timer button, you will activate a two-hour countdown
until lights turn o.
B - By pressing the 4 Hour Timer button, you will activate a four-hour countdown
until lights turn o.
10 - Once you have customized your settings and are ready to power o your lights,
press the red ON/OFF button located at the top of the remote.
NOTE: Your Café Lights will automatically remember the last customized settings
and will turn back on in the same mode and/or color scheme.
Step 3 - INSTALLING MULTIPLE CAFÉ LIGHT SETS
Extend the length of your lights by connecting more
than one strand together to form one continuous string
up to 750ft! Simply follow the above installation steps,
making sure each connection between strands is secure
and that the end female receptacle is securely covered
using the receptacle cover.
Step 4 - REMOVING CAFÉ LIGHTS
1 - Always unplug Café Lights from their receptacle prior to removing.
2 - Carefully remove each light individually from the mounting hardware.
NOTE: For your safety, never pull or jerk lights from mounting hardware.
3 - Store lights in a dry location.
Congratulations on your recent purchase of Enbrighten Café Lights. Enbrighten
Café Lights are designed to provide lighting for life with no bulbs to replace ever
again! Purchase additional lights to form one continuous string up to 750ft!
IMPORTANT: Before installation, please read all the warning statements included at the
bottom of these instructions.
In order to ensure proper installation, please follow each step below:
Step 1 - INITIAL SETUP
1 - Carefully unpack Café Lights from box. Remove the wire ties (see warning on
reverse side).
2 - When installing Café Lights outside, a Ground Fault Circuit Interrupter (GFCI)
receptacle should be used. Before installing, plug the Café Lights into the GFCI
receptacle to ensure all lights work properly. IMPORTANT: Unplug the Café Lights
prior to mounting.
Step 2 - INSTALLING CAFÉ LIGHTS
1 - IMPORTANT: Only mount Café Lights to a solid support
structure such as joists, beams, studs or other solid
mounting surfaces.
2 - Each Café Light is designed with a universal keyhole
for mounting with lights hanging downward. Hardware
options include screws, nails, zip ties, hooks and more
(not included).
3 - Use keyhole ear tabs or keyholes to mount power supply.
4 - Guide wires in compliance with local electrical and
building codes may also be used to support Café Lights.
5 - Once appropriate GFCI outlet location, mounting surface and hardware are
determined, mount your Café Lights.
6 - When finished mounting, place the female receptacle cover firmly over the
unused outlet and plug the male plug into the GFCI receptacle.
7 - Locate the remote. Remove the back cover of the remote and insert
two AAA batteries (included) into the empty compartment. Be sure
to note polarity. Do not mix old and new batteries. Firmly replace the
back cover.
8 - To power on your Café Lights, press the red ON/OFF button located
at the top of the remote.
NOTE: Keep remote indoors when not being used. Remote is not
waterproof.
9 - Now that your lights are installed and powered on, take time to
explore the following settings that are programmable via your remote:
SAVE THESE INSTRUCTIONS
See below for electrical rating
Keyhole Ear Tabs
Keyholes
2
3
/
8
in / 6cm
Available in multiple lengths at
www.cafelights.com
Enbrighten Café Lens Shade
Stainless Steel
Model #35917
Enbrighten Café Lens Shade
Oil-Rubbed Bronze
Model #35877
Express your
unique style with a
variety of shapes
and finishes of
Enbrighten Café
decorative shades.
Express your
unique style with a
variety of shapes
and finishes of
Enbrighten Café
decorative shades.
Simplify your Café Light experience by automating your on and o times and add a
decorative shade to give your lights a distinctive style.
We recommend the following models, available at your select retailers or at www.cafelights.com:
Length, feet Bulbs Model Number
366321836
377902448
377911224
Input watt, Max. Location Use
Wet
Model No.
RGB /*/6/*/*
RGB /*/9/*/*
RGB /*/12/*/*
RGB /*/18/*/*
RGB /*/24/*/*
RGB /*/3/*/*
RGB /*/8/*/*
RGB /*/16/*/*
RGB /*/4/*/*
6W
9W
12W
17W
23W
3W
4W
8W
15W
GE Bluetooth Outdoor
Smart Switch (Plug-in)
Model #13868
myTouchSmart Outdoor
Timer (Plug-in)
Model #26898
myTouchSmart
Timer (In-Wall)
Model #26893
GE Bluetooth
Smart Switch (In-Wall)
Model #13869
Wirelessly schedule
and control outside
lights or other devices
from your smartphone
or tablet.
The myTouchSmart
plug-in timer is the
easiest to set timer
on the market. Simply
select your time and go.
The myTouchSmart
In-Wall Timer provides
easy-set controls if
your receptacle is
controlled by a switch.
The GE Bluetooth
In-Wall version
provides the same
Bluetooth control if
your receptacle is
controlled by a switch.
Refer to the manual or visit www.byjasco.com for limitations and restrictions on warranties and the product registration information.
WARNING: When using outdoors use portable luminaires, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and
personal injury, including the following:
a) Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or outlet(s) to be used for the wet location portable luminaire.
Receptacles are available having built-in GFCI protection and are able to be used for this measure of safety.
b) Use only with an extension cord for outdoor use, such as an extension cord of cord type SEW, SEOW, SEOOW, SOW, SOOW, STW, STOW, STOOW, SJEW,
SJEOW, SJEOOW, SJW, SJOW, SJOOW, SJTW, SJTOW, or SJTOOW.
WARNING: Keep these bags away from babies and children. Do not use in cribs, beds, carriages, or playpens. The thin film may cling to nose and mouth and
prevent breathing.
NOTE: Ensure the Café Light’s receptacle cover is firmly installed and well seated when not being used to connect additional strings.
Warranty Information: This Jasco product is warrantied for three (3) years with a limited-lifetime replacement warranty on Enbrighten LED light source only.
This product is intended (and/or designed) for horizontal hanging. Vertical hanging of the product can void the product warranty.
RISK OF ELECTRIC SHOCK
• RECEPTACLE OUTLETS USED FOR POWERING
CAFÉ LIGHTS SHALL COMPLY WITH ALL NATIONAL
AND LOCAL ELECTRICAL CODES. CONSULT
LOCAL ELECTRICIAN IF UNSURE OF COMPLIANCE
REQUIREMENTS.
• FOR USE ONLY ON GFCI PROTECTED CIRCUITS.
• DO NOT SUBMERSE.
• DO NOT USE AROUND AQUARIUMS.
• CAFÉ LIGHTS ARE A WET LOCATION PRODUCT AND
HAVE NO SERVICEABLE PARTS.
• DO NOT USE WITH EXTENSION CORD NEAR WATER
OR WHERE WATER MAY ACCUMULATE.
• KEEP LAMPS AT LEAST 16 FEET FROM POOLS AND
SPAS.
• KEEP PLUGS AND RECEPTACLES DRY.
• AVOID DAMAGE TO THE CORDS AND LAMP
ASSEMBLIES DURING INSTALLATION. PERIODICALLY
INSPECT THE CAFÉ LIGHTS FOR PHYSICAL DAMAGE
OR OTHER DAMAGE CAUSED BY OUTDOOR
EXPOSURE TO THE ELEMENTS.
• REPLACE ANY DAMAGED CAFÉ LIGHT STRINGS.
• DO NOT INSTALL IN LOCATIONS WHERE CAFÉ
LIGHTS CAN BE STEPPED ON.
• ENSURE CAFÉ LIGHTS ARE UNPLUGGED FROM
POWER DURING INSTALLATION.
• CAFÉ LIGHTS SHOULD BE INSTALLED OUT OF THE
REACH OF CHILDREN OR NOT ALLOWING CHILDREN
TO PLAY WITH THEM.
• UL RECOMMENDS TESTING GFCI CIRCUITS AND
RECEPTACLES EVERY MONTH TO ENSURE PROPER
OPERATION.
• DO NOT OPERATE WITHOUT BULB SECURELY
SCREWED IN.
RISK OF FIRE
• CAFE LIGHTS ARE DESIGNED TO BE
MOUNTED WITH THEIR INDIVIDUAL
KEYHOLE MOUNTING FEATURE, DO NOT
MOUNT CAFÉ LIGHTS BY USING THE MAIN
ELECTRICAL CORD OR THE INDIVIDUAL
DROP CORDS.
• CAFÉ LIGHTS ARE DESIGNED TO BE
LINKED BY USING THEIR ELECTRICAL
PLUGS AND RECEPTACLES TO A
MAXIMUM DISTANCE OF 750 FEET.
• CAFÉ LIGHT INTERCONNECTING
RECEPTACLES ARE INTENDED ONLY
FOR THE LINKING OF COMPATIBLE CAFÉ
LIGHT STRINGS. DO NOT USE CAFÉ
LIGHT RECEPTACLES FOR ANY OTHER
ELECTRICAL PURPOSE.
• DO NOT MOUNT CAFÉ LIGHTS IN ANY
POSITION WHERE THE BULB IS FACING
UP.
• DO NOT ALLOW THE LED LAMP
ASSEMBLIES TO BE IN CONTACT WITH
COMBUSTIBLE MATERIALS. LED LAMP
ASSEMBLIES SHOULD HANG FREELY AND
NOT BE SUSCEPTIBLE TO REPETITIVE
DAMAGE CAUSED BY ENVIRONMENTAL
CONDITIONS SUCH AS WIND, RAIN, AND
ICE.
• NOT INTENDED FOR INSTALLATION IN
CEILINGS, SOFFITS, CABINETS, ATTICS, OR
OTHER ENCLOSED SPACES.
• BATTERIES MAY LEAK HARMFUL LIQUIDS OR IGNITABLE MATERIALS
OR EXPLODE CAUSING INJURY AND PRODUCT DAMAGE.
• DO NOT MIX OLD AND NEW OR OTHER BATTERY TYPES.
• REPLACE ALL BATTERIES AT THE SAME TIME.
• REPLACE EXHAUSTED BATTERIES IMMEDIATELY.
• REMOVE BATTERIES IF PRODUCT IS TO BE UNUSED FOR EXTENDED
PERIODS OF TIME.
MADE IN CHINA
Distributed by Jasco Products Company LLC,
10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 3-year limited
warranty. Visit www.byjasco.com for warranty
details.
Questions? Contact our U.S.-based Consumer Care
at 1-800-654-8483 between 7AM – 8PM CST.
Patents pending | www.cafelights.com
Electrical Ratings
Input: 120V, 50/60 Hz
Important — please read:
WARNING
CAUTION
Version 6
12/19/18
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1 this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Requires 2AAA* batteries.
Observe polarity markings (+), (-).
Seasons