Instructions
ESD-9950-N
SET
°C
°F
P
O1
O2
+ -
S
3
2
1
4
5
ESD-9950-N
SET
°C
°F
P
O1
O2
+ -
S
+
°C
°F
P
O1
O2
++
S
+
°C
°F
P
O1
O2
++
S
+
°C
°F
P
O1
O2
++
S
+
°C
°F
P
O1
O2
++
S
+
°C
°F
P
O1
O2
++
S
+
°C
°F
P
O1
O2
++
S
+
°C
°F
P
O1
O2
++
S
+
°C
°F
P
O1
O2
++
S
+
°C
°F
P
O1
O2
++
S
+
°C
°F
P
O1
O2
++
S
+
°C
°F
P
O1
O2
++
S
+
°C
°F
P
O1
O2
++
S
Note1: PID control parameters ( , , , , ,
) are not seen when parameter �s set as .
Note2: On Off control parameters ( , ) are not seen
when output control type parameter ( ) �s set as .
Note3: Alarm parameters ( , , , , , )
are not seen when output type parameter ( ) �s set as .
Note4: Alarm parameters( , , , , ) are not
seen when alarm type parameter ( ) �s set as .
Note5: If �s d�fferent from and user enters on password
screen, parameter values are observed but can not be
changed.
Access, Change and Record the Parameter Values
Note : If no operat�on for 20 seconds on Parameters Screen, dev�ce automat�cally return Ma�n Screen .
Instruct�on Manual. ENG ESD-9950-N 01 V05 05/18
Front Panel Def�n�t�on
Temperature Un�t Ind�cator
Programm�ng Mode Ind�cator
Status of Control Output 1 (Relay)
Status of Control Output 2 (SSR)
Encoder Button
ESD-9950-N TEMPERATURE CONTROLLER
ESD-9950-N Temperature Controller
- 4 d�g�ts d�splay
- Temperature sensor �nput (TC / RTD)
- Adjustable Process Offset Value
- Programmable ON/OFF, P, PI, PD ve PID control types
- Adaptat�on of PID coeff�c�ents to the system by Auto Tune/Self Tune
- Programmable control and alarm funct�ons for control outputs
ESD-9950-N temperature controllers are des�gned for measur�ng and
controll�ng a temperature value �n �ndustry. They can be used �n many
appl�cat�ons w�th the�r TC and RTD temperature measurement �nput, mult�-
funct�on control outputs, programmable control and alarm funct�ons.
They are ma�nly used �n glass, plast�c, petro-chem�stry, text�le, automot�ve and
mach�ne product�on �ndustr�es. Accurate and advanced controll�ng �s
performed w�th selectable ON-OFF, P, PI, PD, PID, Self Tune PID, Auto Tune
PID funct�ons.
SPECIFICATIONS
INPUT
Process Input: TC/RTD
Thermocouple (TC): J, K, R, S, T and L (IEC584.1)(ITS90)
Thermores�stance (RTD): Cu-50 and Pt100 ( IEC 751) (ITS90)
Measurement Range: Please refer to parameter �n parameters sect�on.
Accuracy: ± 0.25% of scale for thermocouple and thermores�stance.
Cold Junct�on Compensat�on: Automat�cally ±0.1°C/1°C
L�ne Compensat�on: Max�mum 10 Ohm
Sensor Break Protect�on: Upscale
Sampl�ng Cycle: 0.1 second
CONTROL
Control Forms: ON/OFF, P, PI, PD veya PID (Control form can be
programmed by the user.)
OUTPUT
Process Output: Relay(7A@250VV at res�st�ve load) or SSR Dr�ver Output
(Max�mum 10mA, Max. 17VZ )
Alarm Output:Relay (7A@250VV at res�st�ve load)
DISPLAY
Temperature D�splay: 16 mm Red 4 d�g�ts LED D�splay
Led Ind�cators: O1 (Relay Process Output Status LED), O2 (SSR Process
Output Status LED), P(Programm�ng Mode LED),S(Set Value LED),ºC, ºF LEDs
ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS
Operat�ng Temperature: 0...50ºC
Hum�d�ty : 0-90%RH (none condens�ng)
Protect�on Class: IP65 at front , IP20 at rear
We�ght: 350 gr.
D�mens�on: 96 x 96 mm, Depth: 100 mm
Panel CutOut: 92 x 92 mm
SUPPLY VOLTAGE
230VV (±15%) 50/60Hz - 3VA
115VV (±15%) 50/60Hz - 3VA
24VV (±15%) 50/60Hz - 3VA
Must be determ�ned �n order.
Panel Mount�ng
Electr�cal W�r�ngs
To reduce the effect of electr�cal no�se on dev�ce, low voltage l�ne (espec�ally sensor
�nput cables) w�r�ng must be separately from h�gh current and voltage l�ne. If
poss�ble, use sh�elded cable abd sh�eld must be connected to ground only one s�de.
Panel Cut-out
92 mm / 3.62 �nch(m�n)
92 mm / 3.62 �nch(m�n)
129 mm / 5.08 �nch(m�n)
129 mm / 5.08 �nch(m�n)
Note : If no operat�on for 10 seconds, dev�ce automat�cally ex�ts from Set Value Screen w�thout sav�ng the value.
Access and Change Set Value
Press encoder button
to observe the set value.
Turn left encoder button
to decrease or turn r�ght
to �ncrease the set value.
Press encoder button
to save new set value
and return the ma�n screen
ESD-9950-N
ESD-9950-N
Ma�n Screen
ESD-9950-N
Ma�n Screen
ESD-9950-N
Set Value Screen Set Value Screen
Press encoder
button
dur�ng 5 seconds.
Approve password
w�th encoder button.
Enter the password
w�th encoder button.
Turn left encoder button
to decrease or turn r�ght
to �ncrease value.
If no pr�vacy lock �dent�f�cat�on
Parameters Screen w�ll be
observed. If pr�vacy lock �s
�dent�f�ed, w�ll be
observed. Press encoder button
to access Password Screen.
ESD-9950-N
SET
Ma�n Screen
SET
Password Screen
SET
Password Screen Parameters Screen
If Parameters Screen is
active, "P" led blinks. To
observe previous
parameter, turn encoder
button left. To observe
next parameter, turn
encoder button right.
Press encoder button to
observe parameter value.
Parameters Screen
ESD-9950-N
Parameters Screen
ESD-9950-N
Parameters Screen
ESD-9950-N
Parameters Screen
Turn encoder button
left to observe
previous parameter or
turn right to observe
next parameter.
Turn encoder button
left to observe
previous parameter or
turn right to observe
next parameter.
Turn encoder button
left to observe
previous parameter or
turn right to observe
next parameter.
Turn encoder button
left to observe
previous parameter or
turn right to observe
next parameter.
Press encoder button
to observe
the parameter value.
ESD-9950-N
Parameters Screen
To increase parameter
value, turn encoder
button right. Press
encoder button to save.
To decrease parameter
value, turn encoder
button left. Press encoder
button to save.
D�mens�ons
96 mm / 3.78 �nch
96 mm / 3.78 �nch
84 mm / 3.31 �nch
11.5 1mm / 0.45 �nch
Max�mum 15 mm / 0.59 �nch
1- Before mount�ng the dev�ce �n your panel,
make sure that the cutouts �s of the r�ght
s�ze.
2- Check front panel gasket pos�t�on.
3- Insert the dev�ce through the cutout. If the
mount�ng clamps are on the un�t, put out
them
before �nsert�ng the un�t to the panel.
4- Insert the mount�ng clamps to the two of
des�gnated holes that located on four s�des
of dev�ce.
5- Drag the mount�ng clamps �n d�rect�on 5
unt�l the dev�ce completely �mmob�le w�th�n
the panel.
6- In order to remove dev�ce push on the
mount�ng clamp as shown w�th arrow 6 and
pull back.
Parameter Values Screen Parameter Values Screen
Temperature Un�t Ind�cator
Set Value Ind�cator
SETSET
°C
°F
P
O1
O2
+
++
S
SET
°C
°F
P
O1
O2
+
++
S
SET
°C
°F
P
O1
O2
+
++
S
SET
SET
°C
°F
P
O1
O2
+
++
S
Relay Output
TC
PT-100
4
5
10
11 12
13
14
15
7A@250VV
6 7 8 9
NCCNO
-
+
10mA@17VZ
SSR Dr�ver
Output
ESD-9950-N
CAT II
O2
(Process
Output 2)
O1
(Process Output 1
or
Alarm Output)
Process Input
(Analog Input)
Supply
Voltage
Supply
Voltage
Sw�tch
N
L
1A T
Fuse
N
L