Vaneau Hinged Shower Enclosure Installation Instructions Size:36"x36"x77"
●Please read these instructions in full before installation IMPORTANT ●Check that the shower base has been installed to the manufacturer’s instructions. Please note - All product is supplied without a tray. ●Opening wall adjustments Adjustment =(35.04"-35.43")x(35.04"-35.43")[(890-900)mm(890-900)mm] GENERAL SAFETY INSTRUCTIONS ● Do not fix the wall profile to newly plastered, painted or papered walls as chemical reaction may cause discolouration to the surface finish.
IDENTIFICATION OF PARTS 6FR02d 6FR02e 6FR02f 6FR02a 6FR02b 6FR07 6FR06 6FR10 6FR02c 6FR15 6FR16 6FR17 6FR01 6FR09 6FR03 6FR11 6FR24 6FR08 6FR04 6FR18 6FR12 6FR13 6FR14 6FR05 6FR19 6FR20 6FR21 6FR22 6FR23 2.5mm 3.
Fixings & fittings supplied Item No.: Part Quantity Part Item No.: Quantity 6FR01 X1 6FR14 6FR02a X1 6FR15 6FR02b X1 6FR16 X1 6FR02c X1 6FR17 X1 6FR02d X1 6FR18 X1 X2 6FR19 X1 6FR02f X1 6FR20 6FR03 X1 6FR21 X1 X8 6FR22 X1 6FR05 X10 6FR23 6FR06 X1 6FR24 X1 6FR25 6FR08 X1 6FR26 X1 6FR09 X1 6FR27 X1 6FR10 X1 6FR28 X1 6FR11 X1 6FR29 X1 6FR12 X4 6FR30 X1 6FR02e 6FR04 6FR07 6FR13 ST4.0x30 ST4.0x30 ST3.5x19 ST4.0x10 X4 X1 ST3.
LH RH This hinged corner entry can be installed in left and right hand. The steps below are based on left hand installation. For the right hand, please follow the steps below in the reverse direction. 35.04"-35.43" (890-900mm) Technical drawing 35.04"-35.
1. 6FR01 6FR09 X1 X1 6FR04 6FR05 ST4.0x30 X8 X8 6FR09 -Put the wall profile 6FR09 and small wall jamb 6FR01 against the wall and ensure they are vertical by spirit level. -Drill the holes(φ6mm)accordingly. -Insert wall plugs 6FR05(8x) into the holes. -Fasten the wall profile and wall jamb on the wall with screws 6FR04(4x). 6FR01 6FR05 6FR04 6FR04 2.
3. 6FR11 6FR16 6FR15 6FR27 ST3.5x35 X1 X1 X1 X1 -Put some lube 6FR27 into the bottom pivot bracket of the vertical profile 6FR11. -Insert the bottom pivot into the bottom pivot bracket. -Cover the top pivot bracket 6FR16 on the top pivot ,then fasten them with screw 6FR15(1X). 6FR15 6FR16 6FR11 4. 6FR24 6FR22 X1 X1 - Attach the vertical cushion sealer 6FR24 on the edge of front panel. - Measure the size of the bottom anti-water sealer 6FR22, cut off the extra part.
5. -Insert the front panel 6FR08 into the wall profile 6FR09 -Insert the side panel 6FR03 into the small wall jamb 8FR01. -There is a 10mm adjustment between the wall profile and glass panel. 6FR03 X1 6FR03 10m 6. 6FR12 10 m 6FR13 6FR14 6FR28 ST4.0x10 X4 X4 X4 X1 mm - Adjust the front panel and side panel to make them match each other's position. -From inside, drill through the vertical profile into wall profile where shown, using a φ2.8 drill bit 6FR28.
7. 6FR02a 6FR02b 6FR02c 6FR02d 6FR02e 6FR02f 6FR05 6FR25 6FR26 2.5mm 3.0mm ST4.0x30 X1 X1 X1 X1 X2 X1 X2 X1 X1 -Put the glass clip 6FR02c on the side panel, fasten the bottom of clipper with inner screws using hex hey 6FR26. -Insert one side of support bar 6FR02a into the the glass clipper. -Attach the wall bracket 6FR02d on the other side of support bar,ensure it is level by sprint level,and mark the position of wall bracket on the wall.
8. 6FR06 6FR07 6FR10 6FR18 -Put the top cover 6FR06 on the small wall jamb, and fasten it with screw 6FR07 using tool 6FR30. -Put the top cover 6FR10 on the wall profile. -Mount the handle 6FR18 on the front panel. 6FR30 ST3.5x19 X1 X1 X1 X1 X1 6FR30 6FR07 6FR06 10 6FR10 6FR18 9.
10. SILICO NE - Apply silicone sealant to the outside of the enclosure. Please note: Do not apply silicone sealant to the inside of the enclosure. - Do not take a shower within the 24 hours after applying the silicone sealant. Cleaning and Maintenance: Please do not use abrasive or strong cleaning solution on the shower enclosure, such as alcohol, petroleum liquids or any other chemical cleaner with acidic contents.