ELLA ACRYLIC WALK IN BATHTUBS OWNERS MANUAL Ultimate Deluxe Royal Elite 93217 L / 93218 R 93057 L / 93058 R 93117 L / 93118 R 93107 L / 93108 R Petite 93167 L / 931688 R
Table of Contents IMPORTANT Warranty Activation Form MUST be completed for both the Owner and Installer to validate the warranty. Failure to complete both pages (p.18 and p.19) will void the warranty on this bathtub. Completed Ella Warranty Activation Forms can be emailed to warranty@ellasbubbles.com, faxed to 312.666.3551, OR mailed to 2101 S. Carpenter St., Chicago, IL 60608 www.ellasbubbles.
Unpacking and Inspecting Inspect the carton for damage: Take a picture if possible. CAREFULLY RECORD ALL PERCEIVED DAMAGE DO NOT LIFT THE TUB BY THE PLUMBING. Doing so can result in leaks, for which the installer is responsible. All Walk-In Tubs are water tested before they leave our factory and the bath tub you have purchased has passed inspection. Inspect the plumbing for any fittings that may have loosened in transit. You must follow all the instructions in this manual.
Warnings and Labels Your Ella's bathtub comes with several warning label stickers throughout and are as follows: Details on Page 12 Push Control Acrylic Shell Back nut Air hose Details on Page 3 www.ellasbubbles.
Warnings and Labels continued Backnut MUST be securely tightened. Failure to do so will cause loosening over time resulting in it coming apart and falling down the drain. Drain open all the way Drain closed completely Drain must open completely to drain properly and close completely to avoid unnecessary drainage. www.ellasbubbles.
WARNING! PLEASE READ BEFORE BEGINNING INSTALLATION WARNING: Do not attach the hand held shower to the wall unless you have an extension hose with a barrel protection. This may cause water to leak behind your walk in tub. TO INSTALL BARREL EXTENSION HOSE: Water from the hose can drip down into the hand shower base and get behind your tub without the barrel protection. 3)) Take your extension hose and screw t end to the opposite side of the barrel. www.ellasbubbles.
Please heed all warnings listed in the previous pages to avoid potential issues
Moving your Ella Walk in Bath •Remove all four (4) access panels before moving the tub •Take off the screw caps •Unscrew the screws with a Philips head screwdriver •Remove the end access panel Large Access Panel (1) Small Access Panel (2) End Access Panel (4) White Screw Caps Screw Toe Kick Access (3) Washer Cap - Access to parts - Option to lower the Threshold WARNING: Do not carry the walk in tub by the panels.
Important Safety Instructions WARNING: ***Read through the entire manual completely before beginning installation.*** Contract a licensed plumber and electrician for installation. Be sure you and your contractor are aware and follow all local plumbing and electrical codes. Your Ella Walk in Bath is not intended for outdoor use. Install the tub in accordance with the instructions in the manual. Use ONLY the parts and accessories provided or as recommended by the manufacturer.
Important Safety Instructions WARNING: ***USE TUB ONLY AS INTENDED! FAILURE TO DO SO CAN LEAD TO INJURY OR DEATH*** CORRECT WARNING BATHER SHOULD ONLY SIT AS SHOWN IN FIGURE TO THE LEFT. SIT FULLY IN SEAT WITH BACK ON THE BACKREST.
Required Steps Prior to Installation Protecting the Bath Cover and protect the bath shell and fixtures from scratches or other damages during the installation and tests. Remove the access panels when moving the Walk in Bath and always lift the bathtub from the frame. Electrical The unit MUST be connected to a circuit protected by a ground fault circuit interrupter (GFCI) provided and installed by a licensed electrician and tested periodically (refer to instructions provided by GFCI manufacturer).
Drain and Plumbing There are 2 types of drains used for Ella's Bubbles Walk-In Tubs. 2" Brass or PVC T-type. Please refer to the drain delivered with your Walk-In Tub. 2" Brass Drain System Brass Drain Setup: The 2" Brass Drain setup will have a 90o PVC elbow connected to each of the drains. If o you see the 90 PVC elbow, that is how you determine if it is a Brass Drain setup as shown in the diagram to the right.
Drain and Plumbing Positioning Options for 2" Brass Drain Systems Make sure that the drain rough in has been placed at the proper location. The specifications and drawings shown below and on page #7 are for the Ella Deluxe (each model comes with separate specifications, please refer each model's specification). The dual drain can be connected with a “T” or “Y” connection into existing house drain. Proper materials must be used based on local plumbing code requirements.
Drain and Plumbing Positioning Options for 2" T Type Dual Port Drain Systems www.ellasbubbles.
Drain and Plumbing Positioning Options for 2" T Type Dual Port Drain Systems www.ellasbubbles.
Drain and Plumbing Positioning Options for 2" T Type Dual Port Drain Systems www.ellasbubbles.
Door and Frame Adjustments Prepare the sub-floor for the drain and ensure that the area is level. The supporting sub-floor must be able to support the total weight of the bathtub, bather and water and must meet local construction code requirements. Use a level and make sure that the sub-floor below the tub is leveled. If the floor is not perfectly level, adjust the appropriate leveling legs to re-align the tub to perfect level.
Door and Frame Adjustments Your walk in bathtub has been tested and leveled properly before leaving our facility. Our walk in bathtubs have been set on a perfectly level surface to ensure no leaks and proper door closing. It is up to your installer to test and make any adjustments necessary to ensure that all leveling legs support the tub frame and that the door is aligned correctly to prevent any leaks. The door must close smoothly to create a water tight seal.
Door and Frame Adjustments WARNING: Failure to level the tub correctly WILL RESULT IN MISALIGNMENT! The drawings below illustrate some examples of what types of frame warping will occur if the legs are not level with the floor. www.ellasbubbles.
Service Access and Ventilation It is the responsibility of the installer or owner to provide access for service required, per code. Ella is not responsible for any costs related to obtaining access for repair. The owner shall assume responsibility for such costs, and if appropriate, must seek recovery from the installer. Do not insulate around the tub equipment. The tub, frame and all parts have been engineered to provide the proper ventilation.
Installation of Deck Mount Grab Bar Parts List: Chrome grab bar x (1) Escutcheon x (2) Rubber washers x (4) Metal washers x (2) Bolts x (2) WARNING GRAB BAR WASHERS MUST BE INSTALLED TO PREVENT CRACKING OF THE ACRYLIC SHELL, FAILURE TO DO SO WILL VOID THE WARRANTY *THE LARGER METAL WASHER IS THE MOST IMPORTANT OF THE WASHERS, THIS ONE ABSOLUTELY MUST BE INSTALLED TO PREVENT ACRYLIC SHELL DAMAGE Grab Bar Escutcheon Rubber Washer Tub Shell Rubber Washer Metal Washer Bolt * To install the supplied grab
Installing Extension Kits Installing Extension Kits L" Stainless Steel Brackets ...........................Qty (3) L" Acrylic Bracket ........................................Qty (1) 1" x 1/8" Bolts ............................................... Qty (7) 1" x 1/4" Bolts ............................................... Qty (7) 1" Screw ....................................................... Qty (1) 1/2" Nuts ....................................................... Qty (9) 3/8" Nuts .............................
Finishing Installation After all of the water and electrical testing is completed and all fixtures are checked, the tub can be installed to the surrounding wall or walls. Ella Walk in Baths come with low rise tile flange which allows for two or one wall installations. The extension panel of the bathtub can be installed as needed for 60" openings.
Cleaning and Maintenance Recommended Acrylic Cleaners Use only cleaning products whose labels state that they are SAFE for ACRYLIC. Always test products on a small are of skirt before applying to complete bath area. DO NOT USE the following on your ACRYLIC Bath System. The use of the following chemicals will cause a dull surface or chemical cracks. The use of these products will VOID YOUR WARRANTY.
Cleaning and Maintenance Recommended Acrylic Cleaners Acrylic tubs provide customers with a better quality tub vs gel coat tubs. Unfortunately, these tubs can scratch if cleaned incorrectly. The way to proceed is gently, very gently. The good news: gentle cleaning does not translate into high maintenance. On the contrary, you'll probably save some cash by foregoing pricey chemical cleansers.
Cleaning and Maintenance Hospital and Nursing Home Approved Bathtub Disinfectant DISINFECTANT 100337 NUTRA-MAX ® Is a Proven One-Step Disinfectant, Cleaner, Fungicide and Virucide*. For Hospitals, Nursing Homes, Hotels & Motels, Institutional, Industrial Sites, Schools, Restaurants, Food Handling and Processing Areas, Bars and Institutional Kitchens. ACTIVE INGREDIENTS: Didecyl Dimethyl Ammonium Chloride ................... 1.27% Alkyl (50% C14, 40% C12, 10% C16) Dimethyl Benzyl Ammonium Chloride.........
4-Fold BathScreen Installation Instructions
●Please read these instructions in full before installing. IMPORTANT ●Check that the bath has been installed to the manufacturer’s instructions. ●Opening wall adjustments 4-Fold Bath Screen - adjustment =44"-42"(1108-1118mm) GENERAL SAFETY INSTRUCTIONS ●Do not fix the wall profile to newly plastered, painted or papered walls as chemical reaction may cause discolouration to the surface finish. ●lmportant: The wall plugs included in this pack are for solid walls only.
IDENTIFICATION OF PARTS N4FS08 N4FS07 N4FS06 N4FS05 N4FS10 N4FS04 N4FS09 N4FS01 N4FS02 N4FS03 Fixings & fittings supplied Quantity Item No.: N4FS01 x1 N4FS07 x1 N4FS02 x1 N4FS08 x9 N4FS03 x1 N4FS09 x4 x4 N4FS10 x4 x4 N4FS11 Item No.
LH RH Four fold bath screen is ok to be installed in left hand or right hand. Below steps are based on left hand. For right hand, please follow below steps in mirror direction. THE SCREEN MUST BE INSTALLED ON THE OPPOSITE SIDE OF THE EXTENSION PANEL. FAILURE TO DO SO WILL RESULT IN A GAP BETWEEN THE SCREEN AND TUB DECK 1. N4FS08 N4FS02 9X 1X - Put top cover(N4FS08) on the top of the pivot of the screen frame(N4FS02).
2. - Loosen the screw in the bottom of the vertical profile, remove the bottom bracket. - Cut the soft edge of the seal N4FS03 by 3"(75mm) on one end. - Insert the seal into the bottom aluminum frame. - Tie off the end of the seal keep it from moving. - Put the bottom cap on the vertical profile, fix it with screw. N4FS03 1X Note: Please observe cut required. 3 "( 7 5 m m ) N4FS02 3. - Put the wall profile(N4FS01) against the wall and ensure it is vertical using a spirit level.
- Drill the holes(Ø6mm) according to the marks and 4. N4FS06 insert the wall plugs(N4FS06) into the holes. 4X N4FS06 5. N4FS05 N4FS01 - Fasten wall profile(N4FS01) on the wall with screw (N4FS05).
6. - Insert screen panel into wall profile. - There is 0.39"(10mm )adjustment between panel and wall profile for any out of true walls. - Adjust the screen panel in correct position and make sure glass panel fits parallel to the bath edge, but does not sit down directly on bathtub edge. 0 .3 9 "( 1 0 7. mm) N4FS04 N4FS09 N4FS10 3.2 ST4X10 4X 4X 4X - From inside drill through the vertical profile and into wall profile where shown, using a 3.2 mm drill.
8. - Put top cap N4FS07 on the top of wall profile. N4FS07 1X N4FS07 9. SILICO NE - Apply silicone sealant to the outside of the enclosure. Please note: Do not apply silicone sealant to the inside of the enclosure. Sealant drying times may vary in cold damp conditions and will be extended where thicker beads of sealant are applied. Allow sealant to dry completely before exposing to water.
10. N4FS11 SILICONE GREASE - Before the first use, apply the silicone grease on each joint part as below drawing to make the opening and closing smoothly. 1X Cleaning and Maintenance: Please do not use abrasive or strong cleaning solutions on the shower enclosure, such as alcohol, petroleum liquids or any other chemical cleaner. Should there be any dirty stains on the shower enclosure, please clean it with a soft lint free cloth and warm soapy water. Please rinse it with clean water afterwards.
11. You may need to cut into the 4-Fold Screen if your walk-in bathtub has a tile edge or decorative deck lip. Please see below. If your walk-in bathtub has a tile edge or decorative deck lip, you will need to carefully cut out a small section so that your 4-fold screen will sit flush with the tub deck.
12. WARNING The 4-fold Screen MUST BE installed on the opposite side of the extension panel as shown below. Failure to do so WILL result in a gap between the screen and the tub. If your walk-in bathtub has a flange or tile edge, please refer to step 11. You will need to CAREFULLY cut out a notch as illustrated on step 11 in the aluminum frame of the screen for it to sit flush with the deck of your walk-in bathtub.
May not be applicable to your specific package Refer to your package diagrams for more information Additional Operating Instructions by the Original Part Manufacturer TOUCHSTONE Dual Load Controller CIMC-296-01-01-01 (15 Amp) CIMC-296-01-02-01 (20 Amp) Configuration #1 Single Speed Pump Variable Speed Blower Owner’s Manual 22 of 38
May not be applicable to your specific package Refer to your package diagrams for more information Important Safety Instructions PLEASE READ CAREFULLY PRIOR TO Troubleshooting and Servicing Electrical Equipment Definitions: WARNING (May cause serious injuries or death) CAUTION (May cause property damage) For information on NuWhirl Instructions, see: www.nuwhirl.com/docs/product-instructions.
May not be applicable to your specific package Refer to your package diagrams for more information TOUCHSTONE Dual Load Bath Control System Configuration #1 Owner’s Manual Your whirlpool bathtub has been equipped with TOUCHSTONE Electronic Controls to provide features that allow you to customize your bathing experience to your individual preference. Please familiarize yourself with the features and operating instructions below in order to maximize the enjoyment you receive from your bath.
May not be applicable to your specific package Refer to your package diagrams for more information Air Button Operating Instructions Single Speed Pump (Water): The Whirlpool Water System is activated by pressing the Water Button. Ensure first that there is sufficient water in the Tub to at Water least cover the Jets. (If not, the Water Detection Function will prevent the Pump from starting dry). This will turn on the Pump, and activate its 20-minute timer.
May not be applicable to your specific package Refer to your package diagrams for more information TOUCHSTONE Dual Load Bath Control System Configuration #1 Owner’s Manual Electronic Keypad Operating Instructions Keypad Backlighting: When in Standby, the keys are not lighted. When in use, Blue keys indicate "No Water Detected", and Green keys indicate "Water Is Detected". When a function is in use, its key will light Red. When a fuction is off, its key will light Blue or Green as noted above.
May not be applicable to your specific package Refer to your package diagrams for more information TOUCHSTONE Dual Load Control System Installation Instructions System Identification: CIMC-296-01-[01 or 02]-01 01 Configuration #1 System features: Air Buttons or Electronic Keypad, Independent Timers, Single-Speed Single Pump, Variable-Speed Blower, Multi-Color LED Tub Lights, Conductive Water Detect.
May not be applicable to your specific package Refer to your package diagrams for more information TOUCHSTONE Surface Heater Controller System For controller CIHC-300-01-01-01 Installation & Operating Instruction Manual NuWhirl Systems Corp • www.nuwhirl.
May not be applicable to your specific package Refer to your package diagrams for more information Important Safety Instructions PLEASE READ CAREFULLY PRIOR TO Troubleshooting and Servicing Electrical Equipment Definitions: WARNING (May cause serious injuries or death) CAUTION (May cause property damage) For information on NuWhirl Instructions, see: www.nuwhirl.com/docs/product-instructions.
May not be applicable to your specific package Refer to your package diagrams for more information TOUCHSTONE Surface Heater Control System Installation Instructions Your whirlpool bathtub has been equipped with TOUCHSTONE Electronic Controls to provide features that allow you to customize your bathing experience to your individual preference. Please familiarize yourself with the features and operating instructions below in order to maximize the enjoyment you receive from your bath.
May not be applicable to your specific package Refer to your package diagrams for more information Electronic Keypad Your Surface Heater System is controlled by a single electronic keypad power switch or combination heater and light keypad. . When LED is lit the Surface Heaters are running.
May not be applicable to your specific package Refer to your package diagrams for more information TOUCHSTONE Surface Heater Control System Installation Instructions Operating Instructions Surface Heaters It is recommended to turn the Surface Heater ON 5-10 minutes prior to entering the tub. Once the Heater Button is pressed the red LED indicator will illuminate and start a 30-minute timer. The Heater will begin to warm the surface of the seat and/or back wall.
May not be applicable to your specific package Refer to your package diagrams for more information System Identification: CIHC-300-01-01-01 System features: Electronic Keypad, Timer, Surface Heaters, Optional Multi-color LED Lights Controller Installation To Surface Heaters 24VDCPower Connectors Power In 120V 15A GFCI Surface Heater Male Cord Plug located on TOP Max 96 Watts Heater Blanket Load CCBL 382 CIHC-300-01-01-01 Surface Heater Controller CCBL-366 Keypad CIDU-252-03-01-01 or CIDU-252-03-0
May not be applicable to your specific package Refer to your package diagrams for more information TOUCHSTONE Surface Heater Control System Installation Instructions Connect cables to ports as shown. Installation may not require the use of all connection ports. CAUTION: Failure to connect cables to ports as shown, may damage the control box and its components and void any warranties.
May not be applicable to your specific package Refer to your package diagrams for more information TOUCHSTONE Air-Activated Controller TOUCHSTONE Air-Activated Controller Owners Manual Owners Manual Product Illustration: NEMA Plug WARNING: Keep dry. Replace control if subjected to contamination or flooding. Product Illustration: NEMA Socket Rear View Front View NEMA Socket NEMA Plug Air Tube Nipple WARNING: Keep dry. Replace control if subjected to contamination or flooding.
Ella Acrylic Walk In Bath Warranty Information This limited lifetime warranty is extended to the first purchaser to be free from defects in workmanship and material under normal use and conditions from the date of the original purchase. This warranty is nontransferable and applies only to the original owner and to the original installation place – address only and does not extend to products previously used as display models or products that have been modified or repaired by anyone else but Ella’s Bubbles.
Warranty Activation Form 1 of 2 INSTALLER'S INFORMATION ________________________________________________________________________________________ Page 1 Name ________________________________________________________________________________________ Address City State Zip __________________________________ Telephone __________________________________________________ Email __________________________________ Date __________________________________________________ Signature Upon completing the installation
Warranty Activation Form 2 of 2 OWNER'S INFORMATION ________________________________________________________________________________________ Name ________________________________________________________________________________________ Address City State Zip __________________________________ Telephone __________________________________________________ Email __________________________________ Date __________________________________________________ Signature Model: ____________________________________
