Specification Sheet

ManualsBrandsElkay ManualsDrinking FountainsElkay SwirlFlo 19-3/4" Wall Mounted Single Drinking Station with Cooler - Vandal Resistant Bubbler

FLOORLINE

CHILLER SHELF

(476mm)

(130mm)

MIN.DEPTH

(203mm)

TOFLOOR LINE

LOCATION ON CHILLER

(29mm)

(NOTPROVIDED)

(959mm)

(114mm)

FRAME

(10 REQ’D)-(NOTPROVIDED)

(NOTPROVIDED)

HOOKRODS(2)

FLOOR LINE

CHILLER SHELF

(476mm)

(130mm)

MIN. DEPTH

(203mm)

TO FLOOR LINE

LOCATION ON CHILLER

(29mm)

(NOT PROVIDED)

(959mm)

(114mm)

FRAME

(10 REQ’D) - (NOT PROVIDED)

(NOT PROVIDED)

HOOK RODS (2)

(79mm)

(29mm)

(206mm)

(238mm)

MINIMUMDEPTH

(16mm)

(467mm)

(140mm)

(89mm)

BACK WALL LINE

FURNISHED

(41mm)

(730mm)

(203mm)

(114mm)

(29mm)

(279mm)

FINISHED FLOOR

ELECTRICAL INLET

REQUIREMENT

(863mm)

(519mm)

(517mm)

(73mm)

(356mm)

(502mm)

COLD WATER OUTLET

SHUTOFFVALVE BY OTHERS

(25mm)

(79mm)

(29mm)

(206mm)

(238mm)

MINIMUM DEPTH

(16mm)

(467mm)

(140mm)

(89mm)

BACK WALL LINE

FURNISHED

(41mm)

(730mm)

(203mm)

(114mm)

(29mm)

(279mm)

FINISHED FLOOR

REQUIREMENT

(863mm)

(519mm)

(517mm)

(73mm)

(356mm)

(502mm)

COLD WATER OUTLET

SHUT OFF VALVE BY OTHERS

(25mm)

FIG. 2

FIG. 1

OPERATION OF QUICK CONNECT FITTINGS

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

A B

OPERATION OF QUICK CONNECT FITTINGS

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

A B

NOTE:WATERFLOW

DIRECTION

SERVICE STOP

(NOTFURNISHED)

3/8"O.D.TUBECONNECT

COLD WATERSUPPLY

1/4"O.D.TUBE

WATERINLET

TOCOOLER

BUILDINGWATER

INLET

NOTE: WATERFLOW

DIRECTION

SERVICE STOP

(NOT FURNISHED)

3/8" O.D. TUBE CONNECT

COLD WATER SUPPLY

1/4" O.D. TUBE

WATER INLET

TO COOLER

BUILDING WATER

INLET

IMPORTANT!

INSTALLER PLEASE NOTE:

The grounding of electrical equipment such as tele-

phone, computers, etc., to water lines is a common

procedure. This grounding may be in the building or

may occur away from the building. This grounding

can cause electrical feedback into a water cooler,

creating an electrolysis which causes a metallic

taste or causes an incre

ase in the metal content of

the

water. This condition is avoidable by using the

proper materials as indicated below.

The drain fittings which are provided by the installer

should also be plastic to electrically isolate the cooler

from the building plumbing system.

LRPBM8K MOUNTING FRAME INSTRUCTIONS

1. Cut a square rectangular wall opening 18-3/4"

(476mm) W x 37-3/4" (959mm) H and 4-1/2"

(114mm) above the floor line. These dimensions

e required to obtain proper rim and bubbler

heights for compliance with ANSI standard

A117.1. (See Figure 2)

2. Reinforce the wall opening on all sides so that it

will adequately support the water fountain. This

reinforcement must support up to 150 lbs static

load and provide a means for securing the frame

assembly in place.

NOTE: Building construction must allow for ade-

quate

air flow on both sides and top of remote

chille

r unit. Minimum of 4" (102mm) is required.

(See Figures 1 & 2)

3. Install plumbing and electrical rough-ins.

See Figure 1 for location of the supply water inlet

to chiller and for the location of the waste water

outlet. A junction box for a (3) wire, 10 amp branch

circuit is provided on the inside of the chiller.

(Standard 120 Volts, 60 Hz and single phase) See

Figur

e 2 for the electrical inlet location.

4.Remove frame and related hardware from

packaging. Release the two shelf rods by cutting

cable ties. Install the frame squarely in wall

opening with frame upright edges flush with the

finished wall face. (See Figure 2) Place shelf

inside frame and line up the (2) holes on each.

Insert loose ends of rods into holes on sides of

shelf panel. Using appropriately sized wood

scr

ews (not provided), fasten the shelf and frame

to bottom of wall opening. (See Figure 2) Secure

the frame sides and top to the wall using (10)

5/16" x2" lag bolts or screws (not provided).

NOTE: Be sure that frame is squared in location.

Do not use less than the required screw quantity

and size.

2222 Camden Court

Oak Brook, IL 60523

elkay.com

Printed in U.S.A.

Elkay

12-45E

(Rev. 12/15)

No Lead SwirlFlo

with WaterSentry

VII Filter System

Barrier-Free Access

Model LRPB(M)8K

ROUGH-IN DIMENSIONS

WaterSentry

VIIFilterSystem

WaterSentry

VII Filter System

ELECTRIC INLET