Installation Guide

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC, ERPB2-8C*2C, ERPB2-8C*3C
ERPB2-8GRNC*A, ERPB2-8GRNRAC*A, LRPB2-8GRNC*A, LRPB2-8GRNRAC*A
97924C (Rev. K - 02/18)
Page 7
B CA
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
A B C
1
2
3
4
5
6
7
8
9
10A
10B
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
56073C
98501C
98871C
98530C
38417001
75632C
70817C
70020C
28395C
97446C
98481C
111008343890
70432C
28708C
28473C
45767C
28343C
45781C
1000002162
55996C
28383C
28384C
1000003513
1000003514
27026C
45768C
56092C
1000001994
56163C
0000000930
75560C
Bubbler Assy
Bubbler Assy (Stream Saver)
Kit - Push Button/Spring/Washer
Kit - Regulator/Holder/Nut
Screw - #8-18 x .37 HHSM
Setscrew - #10-32 x .38
Fttng - Elbow 1/4 x 1/4
Nut - Hex 5/16-18
Bracket - Support
Bubbler Assembly VR
Bubbler Assy. VR StreamSaver
Screw - #10-24 x .62 HHSM
Screw - #8-32 x .38 THSM
Basin - Swirlow
Lower Shell
Fountain Body
Cover Plate
Sleeve
Kit - Union 1/4” x 1/4” (3 Pack)
Strainer (Provided with Chiller)
Back Panel RH ADA
Back Panel LH ADA
Back Panel RH ADA (Green Spec)
Back Panel LH ADA (Green Spec)
Lower Panel
Drain - Plug 1-1/2”
Poly Tubing (Cut To Length)
Kit - Tee - 1/4” (3 Pack)
Gasket - Drain
Assy - Drain/Tailpipe
Screw - 5/16-18 x 1.00 HHMS
PARTS LIST
ITEM NO.
PART NO.
DESCRIPTION
Installation Package
The components for installation are packed in three
separate boxes, regardless of the type of unit being
installed. The boxes contain the following:
Box No. 1: Wall Frame(s)
Box No. 2: Remote Chiller, ECH8
Box No. 3: Fountain Arm and Panels
Additional materials, as noted in the Parts List, are also
shipped in these boxes.
TROUBLESHOOTING & MAINTENANCE
Orice Assembly: Mineral deposits on
orice can cause water ow to spurt or not
regulate. Mineral deposits may be removed
from the orice by poking with a small round
le not over 1/8” diameter, or using a small
diameter wire.
DO NOT le or cut orice
material.
Stream Regulator: If orice is clean,
regulate ow as in Step 11 of the installation
instructions. If replacement is necessary, see
parts list for correct regulator part number.
Actuation of Quick Connect Water Fittings:
Cooler is provided with lead-free connectors
which utilize an o-ring water seal. To remove
tubing from the tting, relieve water
pressure, push in on the gray collar while
pulling on the tubing. (See Figure 13) To
insert tubing, push tube straight into tting
until it reaches a positive stop approximately
3/4”).
Figure 13 – Quick Connect Fittings
Figure 12 – Water Supply Connections
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 • www.elkay.com
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640