Installation Instructions

98004C (REV. B - 6/08)
ENOB8C
8
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
Installation Package
The components for installation are packed in three
separate boxes, regardless of the type of unit being
installed. The boxes contain the following:
Box No. 1: Wall Frame(s)
Box No. 2: Remote Chiller, ECH8
Box No. 3: Fountain Arm and Panels
Additional materials, as noted in the Parts List, are also
shipped in these boxes.
PARTS LIST
ITEM NO.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
56073C
40322C
56011C
55997C
75580C
15027C
28454C
28455C
28474C
28473C
45767C
28343C
36207C
36193C
45813C
50986C
61314C
31376C
56163C
45769C
45768C
56092C
70683C
55996C
28382C
26833C
111008343890
70432C
38417001
75560C
40045C
70817C
70020C
28395C
50203C
56082C
56204C
70022C
70644C
31272C
70817C
75507C
Bubbler Assy
Assy -Orifice
Housing Assembly
Pedestal
Bubbler Locknut
Brkt - Swirlflow
Brkt - Solenoid/Reg/Wire
Assy - Brkt Solenoid/Reg/Wire
Basin - Swirlflow
Lower Shell
Fountain Body
Cover Plate
Wire - Extension
Assy - Sensor Eye
Sleeve - Swirlflow EE
Holder - Regulator
Regulator
Cord - Power 115V
Gasket - Drain
Assy - Drain/Tailpipe
Drain - Plug 1-1/2”
Poly Tubing (Cut To Length)
Fitting - Union 1/4 x 1/4
Strainer (Provided With Chiller)
Back Panel
Lower Panel
Screw - #10-24 x .62 HHMS
Screw - #8-32 x .38 THTC
Screw - #8-18 x .37 HHSM
Screw - 5/16-18 x 1.00 HHMS
Nut - Hex 1 5/16
Fttng - Elbow 1/4 x 1/4
Nut - Hex 5/16-18
Bracket - Support
Bushing - Strain Relief
Nut - Regulator
Lens - Swirlflow EE
Screw - #6-32 x .31 Set
Screw - #6-32 x .50 PHMS
Solenoid Valve
Fttng-Elbow 1/4 Stem x 1/4x90
Fttng-1/4 NPTF x 1/4OD
1. Orifice Assy: Minerals deposits on orifice can cause water flow to
spurt or not regulate. Mineral deposits may be removed
from the orifice with a small round file not over 1/8" diameter or a
small diameter wire. CAUTION: Do not file or cut orifice materials.
2. Stream Regulator: If orifice is free of material deposits regulate
water flow according to instructions on page 4.
3. Sensor Control: The sensor has a 2 second delay time. If sensor
fails to operate valve mechanism or operates erratically, check
the following:
a) Ensure there are no obstructions within a 40 inch radius from
the front of fountain.
b) Check wire connections at the solenoid valve and at the sensor.
CAUTION: Make sure unit is unplugged before checking any
wiring.
c) Ensure proper operation of solenoid valve. If there is an audible
clicking sound yet no water flows, look for an obstruction in the
valve itself or elsewhere in the water supply line.
WARNING: Do not expose sensor to direct sunlight.
4. Sensor Range Adjustment: The electronic sensor used in this
fountain is factory pre-set for a "visual" range of 36 inches. If
actual range varies greatly from this, or a different setting is desired,
follow the range adjustment procedure below:
a) Remove front lens.
b) Locate range adjustment screw between the lenses of the
sensor, then with a small tip screwdriver, rotate the range adjust-
ing screw clockwise to increase range or counter-clockwise to
decrease range. 1/4 turn of screw is equal to approximately
12 - 18 inches of range.
CAUTION: Complete range of sensor (24 - 46 inches) is only one
turn of the adjusting screw.
c) Replace Lens.
CARE AND CLEANING INSTRUCTIONS
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
TROUBLE SHOOTING AND MAINTENANCE
DO NOT use abrasive or chemical cleaners to clean the sensor lens.
They may dull the luster and attack the plastic cover and chrome
finish of the fountain. Use ONLY soap and water, then wipe with
clean cloth or towel. When cleaning adjacent surfaces, the fountain
and the sensor lens should be protected from any splattering of
cleaners. Acid and cleaning fluids can discolor and damage chrome
plating and plastic sensor lens.
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640