Installation Instructions

ManualsBrandsElkay ManualsDrinking FountainsElkay 7.5 GPH ADA Wall Mount Bi-Level Hands Free (No Suggestions) Cooler with Cane Apron

98005C (REV. C - 6/08)

PARTS LIST

ITEM NO.

PART NO.

DESCRIPTION

56073C

40322C

56011C

55997C

75580C

15027C

28455C

28474C

28473C

45767C

28343C

45781C

45847C

45848C

50986C

61314C

15005C

56163C

45769C

45768C

56092C

70682C

55996C

28383C

28384C

27026C

111008343890

70432C

38417001

75560C

75632C

70817C

70020C

28395C

36207C

36193C

45813C

31376C

40045C

50203C

56082C

56204C

70022C

70644C

31272C

70817C

75507C

28454C

75671C

Bubbler Assy

Orifice Assy

Housing Assembly

Pedestal

Bubbler Locknut

Brkt - Swirlflow

Assy - Brkt Solenoid/Reg/Wire

Basin - Swirlflow

Lower Shell

Fountain Body

Cover Plate

Sleeve

Pin - Push Button

Push Button

Holder - Regulator

Regulator

Retaining Nut

Gasket - Drain

Assy - Drain/Tailpipe

Drain - Ferrule

Poly Tubing (Cut To Length)

Tee - 1/4

Strainer (Provided with Chiller)

Back Panel RH ADA

Back Panel LH ADA

Lower Panel

Screw - #10-24 x .62 HHSM

Screw - #8-32 x .38 THSM

Screw - #8-18 x .37 HHSM

Screw - 5/16-18 x 1.00 HHMS

Setscrew - #10-32 x .31

Fttng - Elbow 1/4 x 1/4

Nut - Hex 5/16-18

Bracket - Support

Wire - Extension

Assy - Sensor Eye

Sleeve - Swirlflow EE

Cord - Power 115v

Nut - Hex 1 5/16

Bushing - Strain Relief

Nut - Regulator

Lens - Swirlflow EE

Screw - #6-32 x .31 Set

Screw - #6-32 x .50 PHMS

Solenoid Valve

Fttng-Elbow 1/4 Stem x 1/4x90

Fttng-1/4 NPTF x 1/4OD

Brkt -Solenoid/Reg Swirlflo

Spring - Push Button

ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484

FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620

Installation Package

The components for installation are packed in three

separate boxes, regardless of the type of unit being

installed. The boxes contain the following:

Box No. 1: Wall Frame(s)

Box No. 2: Remote Chiller, ECH8

Box No. 3: Fountain Arm and Panels

Additional materials, as noted in the Parts List, are also

shipped in these boxes.

1. Orifice Assy: Minerals deposits on orifice can cause water flow to

spurt or not regulate. Mineral deposits may be removed

from the orifice with a small round file not over 1/8" diameter or a

small diameter wire. CAUTION: Do not file or cut orifice materials.

2. Stream Regulator: If orifice is free of material deposits regulate

water flow according to instructions on page 4.

3. Sensor Control: The sensor has a 2 second delay time. If sensor

fails to operate valve mechanism or operates erratically, check

the following:

a) Ensure there are no obstructions within a 40 inch radius from

the front of fountain.

b) Check wire connections at the solenoid valve and at the sensor.

CAUTION: Make sure unit is unplugged before checking any

wiring.

c) Ensure proper operation of solenoid valve. If there is an audible

clicking sound yet no water flows, look for an obstruction in the

valve itself or elsewhere in the water supply line.

WARNING: Do not expose sensor to direct sunlight.

4. Sensor Range Adjustment: The electronic sensor used in this

fountain is factory pre-set for a "visual" range of 36 inches. If

actual range varies greatly from this, or a different setting is desired,

follow the range adjustment procedure below:

a) Remove front lens.

b) Locate range adjustment screw between the lenses of the

sensor, then with a small tip screwdriver, rotate the range adjust-

ing screw clockwise to increase range or counter-clockwise to

decrease range. 1/4 turn of screw is equal to approximately

12 - 18 inches of range.

CAUTION: Complete range of sensor (24 - 46 inches) is only one

turn of the adjusting screw.

c) Replace lens.

TROUBLE SHOOTING AND MAINTENANCE

CARE AND CLEANING INSTRUCTIONS

DO NOT use abrasive or chemical cleaners to clean the sensor lens.

They may dull the luster and attack the plastic cover and chrome

finish of the fountain. Use ONLY soap and water, then wipe with

clean cloth or towel. When cleaning adjacent surfaces, the fountain

and the sensor lens should be protected from any splattering of

cleaners. Acid and cleaning fluids can discolor and damage chrome

plating and plastic sensor lens.

REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640

ENOB2-8C, ENOB2-8RAC