Installation Sheet

ManualsBrandsElkay ManualsPopular CollectionsElkay EZH20 17-7/8" Wall Mounted Bottle Filler

1000002042 (Rev.D-09/15)

EMASMB*A & LMASMB*A

Page 6

SETTING THE CONTROL BOARD

VERIFY CONTROL BOARD SOFTWARE

1) To verify the software program of the control board the

unit will need to be shut down and restarted. The chiller

(if present) does not need to be shut down and restarted.

2) Shut down the unit by removing a battery.

3) Restart the unit by installing the batteries

4) Upon start up the bottle count display will show the

software designation of 'ELKAY BC'.

ACCESSING THE PROGRAMING BUTTON

1) To access the program button, remove the two (2)

screws holding the Bottom Cover in place. Button is located

within nger reach from the underside of the unit on the back

right hand side of the battery/lter tray.

2) When nished setting control board, reinstall the Bottom Cover

and secure with the same two (2) screws.

RESET THE FILTER MONITOR

1) Instructions apply to ltered units only.

2) Depress the program button momentarily.

The display changes when released. The display will

change and scroll through four messages:

“RST FLTR” – Reset Filter Status LED

“NO FLTR” – EMASMB or non-ltered mode

"500G FLT" – LMASMB or Filtered mode

"RST BCNT“ - Reset bottle count

If the program button is not pushed again the display

will scroll through the four messages above for

and then default back to bottle count and be back in run

mode.

3) When the display changes to “RST FLTR”, depress

the button again. The display will change to show

“FC RESET”. Depress the button again and the display

will show “00000000”

4) There are three (3) LED's that indicate the following:

Green: LED (Good) indicates that the lter is operating

within 0% - 80% of its life.

Yellow: LED indicates that the lter is operating within

80% - 100% of its life.

Red: LED (Replace) indicates that the lter needs to be

replaced since it has reached end of lter life.

and ow restrictions.

RESETTING BOTTLE COUNT

1) Depress the program button momentarily.

The display will change and scroll through four messages:

“RST FLTR” – Reset Filter Status LED

“NO FLTR” – EMASMB or non-ltered mode

"500G FLT" – LMASMB or Filtered mode

“RST BCNT“ - Reset bottle count

If the program button is not pushed again the display

will scroll through the four messages above for

and then default back to bottle count and be back in run mode.

2) When the display changes to “RST BCNT”, push the button

again and the display will show “BC RESET” If the button is not

pushed again the display will return to run mode.

3) Push the program button once more to reset back to 0. The dis-

play will and then return to run mode showing 00000000 bottles.

NOTE: Once the bottle count is reset to zero there is no way

to return to the previous bottle count.

4) Testing the bottle counter:

EMASMB units: Push button for approximately 9 seconds to see

bottle counter count 00000001.

NOTE: Bottle count is approximate and is dependent on water

pressure and ow through the lter. LMASMB units: Push

button for approximately 19 seconds

to see bottle counter count 00000001. NOTE: Bottle count is

approximate and is dependent on water pressure and ow

restrictions.

DESCRIPTION

1000001673

98546C

56192C

KIT-1.0 GPM REGULATOR KIT

KIT-AERATOR

KIT-FILTER REPLACEMENT KIT

REPLACEMENT PARTS

PART NO.

REGULATOR

AERATOR

FILTER

ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484

FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816

REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640

FIGURE 3

B CA

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

OPERATION OF QUICK CONNECT FITTINGS

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE