Installation & Assembly

ManualsBrandsElkay ManualsBathLustertone Undermount Bar Sink in Satin

COUNTERTOP

MOUNTING

BRACKET

(OPTIONAL

ACCESSORY)

COUNTERTOP RECESSED

APPROX. 1/2"

SILICONE CAULK

(NOT FURNISHED)

SINK

1-1/8"

FASTENER

(NOT FURNISHED)

COUNTERTOP

OVERHANG

APPROX. 1/8"

SINK

SILICONE CAULK

(NOT FURNISHED)

FASTENER

(NOT FURNISHED)

MOUNTING

BRACKET

(OPTIONAL

ACCESSORY)

ATTENTION INSTALLER:

1) ELKAY RECOMMENDS THAT UNDERMOUNT SINKS SHOULD BE INSTALLED BY A PROFESSIONAL

EXPERIENCED INSTALLER.

2) WARNING: TEMPLATE IS NOT INCLUDED. PLEASE VISIT ELKAYUSA.COM FOR SINK TEMPLATE.

MAKE SURE THE TEMPLATE YOU CHOOSE WILL GIVE YOU THE DESIRED INSTALLATION LOOK.

ELKAY’S TEMPLATES PROVIDE EITHER A 1/2" REVEAL OF THE SINK FLANGE OR 1/8" OVERHANG

OF THE COUNTERTOP OVER THE SINK BOWL OPENING.

3) ELKAY UNDERMOUNT SINKS SHOULD ONLY BE FASTENED TO A SOLID SURFACE COUNTERTOP

(I.E. GRANITE/CORIAN

/SILESTONE

4) ELKAY IS NOT RESPONSIBLE FOR SINK OR COUNTERTOP IF DAMAGED DURING INSTALLATION.

5) METAL EDGES MAY BE SHARP – USE CAUTION WHEN HANDLING.

6) FOLLOW ALL LOCAL PLUMBING AND BUILDING CODES.

7) INSPECT SINK FOR DAMAGE PRIOR TO BEGINNING INSTALLATION.

INSTALLATION

1. Position template on countertop. Locate the

template front to rear, so that sink will not inter-

fere with the cabinet.

2. Trace a line around the template. Cut along the

inside of this line to provide opening.

3. Locate and drill the mounting holes (following

the countertop manufacturer’s instructions) as

shown below. Holes should allow even spacing

of mounting brackets around the sink. Type of

fasteners to be as recommended by countertop

supplier.

4. Fasten mounting brackets (optional accessory -

LKUCLIP8) to countertop loosely.

5. Using a good quality silicone caulk, apply a bead

evenly all around the top of the sink flanges.

6. Position and align sink over the countertop

opening. Press silicone onto countertop.

7. Tighten fasteners until mounting brackets are

snug against sink.

8. Check alignment of sink to countertop opening.

9. Tighten down fasteners evenly. Be careful not to

overtighten. Remove excess silicone.

Installation Instructions

1/2" SINK RIM REVEAL 1/8" COUNTERTOP OVERHANG

Summary of content (2 pages)

PAGE 1
Installation Instructions 1) 2) 3) 4) 5) 6) 7) ATTENTION INSTALLER: ELKAY RECOMMENDS THAT UNDERMOUNT SINKS SHOULD BE INSTALLED BY A PROFESSIONAL EXPERIENCED INSTALLER. WARNING: TEMPLATE IS NOT INCLUDED. PLEASE VISIT ELKAYUSA.COM FOR SINK TEMPLATE. MAKE SURE THE TEMPLATE YOU CHOOSE WILL GIVE YOU THE DESIRED INSTALLATION LOOK. ELKAY’S TEMPLATES PROVIDE EITHER A 1/2" REVEAL OF THE SINK FLANGE OR 1/8" OVERHANG OF THE COUNTERTOP OVER THE SINK BOWL OPENING.
PAGE 2
Installation Instructions Suggestions for the Care and Cleaning of your Elkay Stainless Steel Sink ELKAY SATIN FINISH Elkay's original highlighted satin finish is produced by an abrasive grinding operation which lends a uniform pattern of satin finish lines to the metal surface. All exposed areas then undergo a series of progressive machine and hand polishing operations. It is this careful polishing that makes an Elkay satin luster finish so beautiful…and so easy to clean and maintain.